Sig-gen-workstation-069658 电路图.pdf

《Sig-gen-workstation-069658 电路图.pdf》由会员分享，可在线阅读，更多相关《Sig-gen-workstation-069658 电路图.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、TECHNICAL MANUALTM 9-6695-295-34P HEADQUARTERS TM 9-6695-295-34P DEPARTMENT OF THE ARMY WASHINGTON, DC, 27 March 1992 1992 DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST FOR SIGNAL GENERATOR WORKSTATION NSN 6695-01-257-2990 Current as of 6 January 1992 CONSISTING

2、OF: DOWN CONVERTER, COMSTRON, MODEL 9000S, RF POWER METER, BOONTON, MODEL 4220-S/10, AUDIO ANALYZER, BOONTON, MODEL 1120-S/10, AND MODULATION ANALYZER BOONTON, MODEL 8200-S/10 TABLE OF CONTENTS Page REPAIR PARTS AND SPECIAL TOOLS LIST SECTION I. INTRODUCTION SectionI.INTRODUCTION.1 SectionII.REPAIR

3、PARTS LIST Group0010Down converter mainframe,9000S.II-1 0020RF power meter mainframe,4220-S/10.II-1 0030Circuit card assembly,A2.II-1 0040Circuit card assembly,A6.II-1 0050Circuit card assembly,A10.II-2 0060Audio analyzer mainframe,1120-S/10.II-2 0070Circuit card assembly, AO.II-3 0080Circuit card a

4、ssembly, Al.II-3 0090Circuit card assembly,A2.II-4 0100Circuit card assembly,A3.II-4 0110Circuit card assembly,A4.II-5 0120Circuit card assembly,A5.II-5 0130Circuit card assembly,A6.II-6 0140Circuit card assembly,A7.II-7 0150Circuit card assembly,A10.II-7 i REPORTING ERRORS AND RECOMMENDING IMPROVEM

5、ENTS You can help improve this manual. If you find any mistakes or if you know of a way to Improve the procedures, please let us know. Mail your letter or DA Form 2028 (Recommended Changes to Publications and Blank Forms) to: Director, U.S. Army TMDE Activity, ATTN: AMXTM-LM-S, Redstone Arsenal, AL

6、35898-5400. A reply will be furnished directly to you. TM 9-6695-295-34P TABLE OF CONTENTS - Continued Page 0160Power supply subassembly, A11.II-8 0170Circuit card assembly, A12.II-8 0180Keyboard, data entry, A13.II-8 0190Circuit card assembly, A24.II-9 0200Modulation analyzer mainframe, 8200-S/10.I

7、I-9 0210Circuit card assembly, A1.II-9 0220Circuit card assembly, A4.II-10 0230Circuit card assembly, A5.II-10 0240Circuit card assembly, A6.II-11 0250Circuit card assembly, A8.II-12 0260Circuit card assembly, A9.II-13 0270Circuit card assembly,A10.II-13 0280Circuit card assembly, A11.II-14 0290Circ

8、uit card assembly, A12.II-14 0300Circuit card assembly, A13.II-14 SectionIII.SPECIAL TOOLS LIST (Not applicable) SectionIV.CROSS REFERENCE INDEXES.IV-1 ii TM 9-6695-295-34P DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE 1.Scope. This Repair Parts and Special Tools List (RPSTL) lists and authorizes s

9、pare and repair parts required for performance of direct and general support maintenance of the Signal Generator Workstation. It authorizes the requisitioning, issue, and disposition of spares and repair parts as indicated by the Source, Maintenance and Recoverability (SMR) codes. 2.General. In addi

10、tion to this Section I, Introduction, this RPSTL is divided Into the following sections: a.Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for use in the performance of maintenance. Parts lists are composed of functional groups in ascending numeric sequence.

11、 Parts are listed in alphabetical sequence within each group and figure number. b.Section III. Special Tools List. Not applicable. c.Section IV. Cross Reference indexes. A list, in National Item Identification Number (NIIN) sequence, of all National Stock Numbered (NSN) items appearing in the listin

12、g, followed by a list in alphanumeric sequence of all part numbers appearing in the listing. NSNs and part numbers are cross-referenced to each illustration figure and item number appearance. The figure and item number index lists figure and item numbers in alphanumeric sequence and cross- reference

13、 NSN, Commercial and Government Entity Code (CAGEC), and part numbers. 3.Explanation of Columns (Section II) a.Figure Number (Column (la). This column lists the number of the figure where the item is located in Section II. b.Item Number (Column (1b). The item number is that number assigned to the it

14、em as it appears in the figure referenced in the adjacent figure number column. c.SMR Code (Column (2). The SMR code is a 5 position code containing supply/requisition information, maintenance category authorization criteria, and disposition instructions as shown in the following breakout. Source Co

15、deMaintenance CodeRecoverability Code _ XX 1st two positionsXX X 5th position How you get an item3d position4th positionWho determines disposition action on an unserviceable item Who can install,Who can do complete replace, or use item repair on the item *Complete repair: Maintenance capacity, capab

16、ility, and authority to perform all the corrective maintenance tasks of the Repair function in a use/user environment in order to restore serviceability to a failed item. 1 TM 9-6695-295-34P (1) Source Code. The source code tells you how you get an item needed for maintenance, repair, or overhaul of

17、 an end item/equipment. Source codes are always the first two positions of the SMR code. Explanation of source codes follows: CodeExplanation PA-Stocked items; use the applicable NSN to request/requisition items with this code. These items are authorized to the category indicated by the code entered

18、 in the third position of the SMR code. (2) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR code as follows: (a) The maintenance code entered in the thi

19、rd position tells you the maintenance level authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to the following level of maintenance. CodeApplication/Explanation F -Direct support level can remove, replace, and use the item.

20、 (b) The maintenance code entered in the fourth position tells you whether or not the item is to be repaired and identifies the lowest maintenance level with the capability to do complete repair (i.e., perform all authorized repair functions). This position will contain one of the following codes: C

21、odeApplication/Explanation H -General support is the lowest level that can do complete repair of the item. Z -Nonreparable. No repair is authorized. (3) Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action on unserviceable items. The recoverability code

22、is entered in the fifth position of the SMR code as follows: RecoverabilityDefinition Codes A-Item requires special handling or condemnation procedures because of specific reasons (i.e., precious metal content, high dollar value, critical material, or hazardous material). These items should be turne

23、d in to your Maintenance Supply Activity (MSA) for forwarding to the Defense Reutilization and Marketing Office (DRMO). H -Reparable item. When uneconomically reparable, condemn and dispose of the item at the general support level. Z -Nonreparable item. When unserviceable, condemn and dispose of the

24、 item at the level of maintenance shown in the third position of the SMR code. d. National Stock Number (Column (3). This column lists the NSN for the associated part number and manufacturer identified in the CAGEC and part number columns to the right. 2 TM 9-6695-295-34P e. CAGEC (Column (4). The C

25、AGEC is a 5-digit numerical code which is used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. f. Part Number (Column (5). Indicates the primary number used by the manufacturer (individual, company, firm, corporation, or Government activity), which cont

26、rols the design and characteristics of the item by means of its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of items. NOTE: When you use an NSN to requisition an item, the item you receive may have a different part number from the part or

27、dered, but go ahead and use or furnish it as the replacement part. g. Description and Usable on Code (UOC) (Column (6). This column includes the following information: (1) The federal item name and, when required, a minimum description to identify the item. (2) The UOC, when applicable (see paragrap

28、h 5, Special Information). h. Quantity (Column (7). The quantity (quantity per figure column) indicates the quantity of the item used in the parts list which is prepared for a functional group, subfunctional group, or an assembly. 4. Explanation of Columns (Section IV) a. NSN Index (1) Stock Number

29、Column. This column lists the NSN by NIIN sequence. The NIIN consists of the last nine digits of the NSN. NSN (i.e., 5305-01-674-1467). When using this column to locate an item, ignore the first 4 digits of NIIN the NSN. However, the complete NSN should be used when ordering items by stock number. (

30、2) Figure Column. Indicates the figure number used to identify each item appearing in the listing. The figures are in numerical order in Section II. (3) Item Column. The item number identifies the item associated with the figure listed in the adjacent figure column. This item is also identified by t

31、he NSN listed on the same line. b. Part Number Index. Part numbers in this index are listed by part number in ascending alphanumeric sequences (i.e., vertical arrangement of letter and number combination which places the first letter or digit of each group in order A through Z, followed by the numbe

32、r 0 through 9 and each following letter or digit in like order). (1) Part Number Column. Indicates the primary number used by the manufacturer (indi- vidual, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, sp

33、ecifications, standards, and inspection require- ments to identify an item or range of items. (2) Figure Column. This column lists the number of the figure where the item is located in Section II. 3 TM 9-6695-295-34P (3) Item Column. The item number is that number assigned to the item as it appears

34、in the figure referenced in the adjacent figure number column. c. Figure and Item Number Index (1) Figure Column. This column lists the number of the figure where the item is identi- fied/located in Section II. (2) Item Column. The item number is that number assigned to the item as it appears In the

35、 figure referenced in the adjacent figure number column. (3) Stock Number Column. This column lists the NSN for the item. (4) CAGEC Column. The CAGEC is a 5-digit numeric code used to identify the manu- facturer, distributor, or Government agency, etc., that supplies the item. (5) Part Number Column

36、. Indicates the primary number used by the manufacturer (individual, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of item

37、s. 5. Special Information a. Repair parts for components of standards sets which can be identified as existing in the supply system will be requisitioned through normal supply channels from the appropriate supply commodity manager. b. Repair parts for components of standards sets which cannot be ide

38、ntified as to proper supply source will be requisitioned from USAMICOM, using routing identifier B64 and furnishing, as a minimum, the following as exception data: (1) Component stock number of the individual end item to be repaired. (2) Component manufacturers equipment model number and serial numb

39、er. (3) The equipment manufacturers reference number as listed in the appropriate manual for the desired repair part. (4) The repair part reference designation, circuit reference, circuit symbol schematic des- ignation, or reference number as listed in the manufacturers manual. (5) The technical spe

40、cification of the repair part as contained in the appropriate manufac- turers manual. (6) The title and date of the manufacturers manual from which the information in a and b(3), (4), and (5) above was taken. c. For requisitioning miscellaneous consumable maintenance supplies or expendable supplies,

41、 use CTA 50-970. 4 TM 9-6695-295-34P d. The usable on code appears in the lower left corner of the Description column heading. Usable on codes are shown as UOC in the Description column (justified left) on the first line applicable item description/nomenclature. Uncoded items are applicable to all m

42、odels. e. This RPSTL does not contain illustrations for items listed in Section II, since the manufacturers manual contains exploded view illustrations which are adequate for repair parts location. Copies of the manufacturers manual for the Signal Generator Workstation are furnished with the equipme

43、nt for which this RPSTL is prepared. The figure and item numbers in the listing are for locating the item within this RPSTL. 6. How to Locate Repair Parts a. When National Stock Number or Part Number Is Not Known. (1) First. Refer to the parts list to locate the item by description. This list is in

44、alphabetical sequence within each group and figure number. Identification of group and figure numbers and the manufacturers manual locational figure numbers are listed below: Manufacturers Manual GroupFigureLocational FigureNomenclaturePart Number 00101- - -Down converter mainframe- - - 00202- - -RF power meter mainframe- - - 00303Page 7-10Circuit card assembly04311001A 00404Page 7-4Circuit card assembly04