Philips LCD backlight 电路图.pdf

《Philips LCD backlight 电路图.pdf》由会员分享，可在线阅读，更多相关《Philips LCD backlight 电路图.pdf（5页珍藏版）》请在收音机爱好者资料库上搜索。

1、Philips LCD backlight Home Replacing the LCD backlight in Philips PM 3055, PM3365 and similar oscilloscopes Please Note : This procedure requires some skill at soldering and at least a minimum amount of electronics knowledge. !Safety Concerns! Make sure the Oscilloscope is OFF and DISCONNECTED from

2、the mains! Use antistatic techniques, the circuits inside can be damaged by STATIC. There are potentially dangerous voltages inside this instrument, however in the area concerned there is only low voltage, but once again.POWER OFF and DISCONNECT FROM THE MAINS and remove any inputs to the oscillosco

3、pe! NO LIABILITY ACCEPTED FOR ANY DAMAGE TO YOU OR YOUR OSCILLOSCOPE FROM FOLLOWING THIS PROCEDURE. Your calibration warranty will probably be void after opening the case. The photos are from a digital PM3365, if you are doing this on the analog versions eg PM3055, it is much simpler in that you do

4、not need to remove the digital unit, access to the LCD panel screws is directly after removing the top cover. When following this procedure DO NOT FORCE ANYTHING! If it wontcome apart or fit back together easily find out why! The LCD is easily damaged both by force or static, be gentle! Dress the ca

5、bles properly and dont forget to put the earth tags back! If you leave them loose they will short something ! Use a small fine tip iron, preferably low voltage eg Weller or if you must use Radioshack get the small earthed type of soldering iron. Mains irons with no earth lead will possibly damage th

6、e circuitry. (1 of 5)3/6/2006 9:38:57 AM RadioFans.CN 收音机爱 好者资料库 Philips LCD backlight After removing the top cover (one screw at rear of case), remove this screw, usually the only one holding the board down Remove 2 Earth tags (remember to replace them!) Lift the shielded board assy up and clip it

7、to the side, the cables are tight but it will go. Lift the digital unit straight up & remove 2 cables Now you can move the digital unit aside just enough to see the 2 screws holding the front panel Remove the 2 long mounting screws (2 of 5)3/6/2006 9:38:57 AM RadioFans.CN 收音机爱 好者资料库 Philips LCD back

8、light The display panel is now loose, ease it out gently Remove the 2 cables Pull all the knobs off The circuit board is held in place by a number of clips. Ease them aside to pop the board out. Be very pleased with yourself if you do this without breaking the clips! (3 of 5)3/6/2006 9:38:57 AM Radi

9、oFans.CN 收音机爱 好者资料库 Philips LCD backlight Now you can see the LCD board Again , ease the clips aside to pop the board out. They almost always break . Dont lose the reflector Now you need to unsolder the 2 lamp wires Insert the new lamp through the holes and push it A bit of tape holds it flush for s

10、oldering, cut the (4 of 5)3/6/2006 9:38:57 AM Philips LCD backlight into the slot wires to length. Solder the wires in place, watch out for solder splashes! Clean and inspect after soldering Remove the tape, the lamp should be flush with the surface, put the reflector in place. The LCD board has to

11、connect to the 2 multi pin connectors Go backwards through this procedure to reassemble the scope and you should have a nice backlit display again! Dont worry if you broke all or most of the board clips, the assembly holds together ok when its screwed back in place Top Home (5 of 5)3/6/2006 9:38:57 AM