fluke BC7217__iseng0100 电路图.pdf

《fluke BC7217__iseng0100 电路图.pdf》由会员分享，可在线阅读，更多相关《fluke BC7217__iseng0100 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、 PN 691862 September 1998 Rev.1, 3/09 1998-2009 Fluke Corporation. All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies. In Case of Difficulty For service help or to contact Fluke for any reason, call one of the following telephone numbers: USA and Ca

2、nada: 1-888-99-FLUKE (1-888-993-5853) Europe: +31 402-678-200 Japan: +81-3-3434-0181 Singapore: +65-*-276-6196 Anywhere in the world: +1-425-356-5500 Or, visit Flukes Web site at . LIMITED WARRANTY & LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for

3、 one year from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Flukes behalf. To obtain service during the warranty pe

4、riod, send your defective tester to the nearest Fluke Authorized Service Center with a description of the problem. THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

5、CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you. Fluke Corporation P.O. Box 9090 Everett WA 9

6、8206-9090 Fluke Europe B.V. P.O. Box 1186 5602 B.D. Eindhoven The Netherlands BC7217-120 BC7217-INTL Battery Chargers Instruction Sheet Introduction The Fluke BC7217 Battery Charger charges Fluke BP72XX series Nickel-Cadmium and Nickel-Metal-Hydride battery packs for handheld test tools. The BC7217

7、consists of a charger base and a power supply. Connecting the Charger to Line Power Model BC7217-120, Model BC7217-INTL Connect the wall adapter to line power within the following range: 90 to 264V ac, 47 to 63 Hz. Plug the barrel connector into the charger dc input jack as shown in Figure 1. zq1f.e

8、ps Figure 1. Connecting the Charger to Line Power RadioFans.CN 收音机爱 好者资料库 Charging the Battery Note Sometimes a new battery needs several charge/discharge cycles before it performs to full capacity. Before you use a new battery for the first time, charge it fully. Connect the charger to line power a

9、nd place the battery in the charger as shown in Figure 2. You can leave the battery pack on trickle-charge indefinitely without damage. The charger will not overcharge a battery, even if you reinsert a charged battery. Nickel-Cadmium Battery To obtain a full charge, charge the battery until the indi

10、cator blinks (approximately 1-1/2 hours). Nickel-Metal Hydride Battery To obtain a full charge, charge the battery until the indicator blinks (approximately 2-1/2 hours), then leave it in the charger 3 more hours for a full charge. Note When you remove a charged battery from the charger, wait for th

11、e blinking indicator to go off before you insert a discharged battery. It takes about 2 seconds for the battery charger to reset. zq2f.eps Figure 2. Inserting the Battery When to Charge Wait until the battery is fully discharged before you charge the battery. The battery will retain its charge longe

12、r. Charge Mode Indicator The red indicator light on the side of the charger shows the status of the battery charge cycle as follows: Off The battery is not inserted, or it is inserted incorrectly, power is disconnected or not available, or the internal fuse is blown. Steady on High-current fast char

13、ge mode. Blinking (50% duty cycle) Nickel-Cadmium battery: trickle-charge mode. Nickel-Metal Hydride battery: pulsed charge for the first 3 hours after blinking starts, then trickle-charge mode. Blinking (less than 50% duty cycle) Pre-charge delay for proper battery temperature or voltage conditions

14、. Internal Fuse An internal fuse is soldered in place. If the charger indicator does not go on when a battery is installed, this fuse may be blown. The fuse cannot be replaced by the user. Specifications BC7217-120, BC-7217-INTL: Wall Adapter: Input Voltage: 90 to 264 V ac Input Voltage Frequency: 4

15、7 to 63 Hz Output Voltage: 15 V dc, 2 A Line power adapters: North America/Japan, Europe, UK, Australia Safety Approvals: UL, CSA and TUV Both Models: Charger Input Voltage: 14 to 20 V dc DC Power Plug Polarity: Ring Negative + Center Positive Temperature: Operating: 0 to 40 C Storage: -20 to 70 C Humidity (noncondensing): Operating: 0 to 90% R.H. Storage: 5 to 95% R.H. RadioFans.CN 收音机爱 好者资料库