Hameg hm303-6 电路图.pdf

《Hameg hm303-6 电路图.pdf》由会员分享，可在线阅读，更多相关《Hameg hm303-6 电路图.pdf（24页珍藏版）》请在收音机爱好者资料库上搜索。

1、O s c i l l o s c o p e H M 3 0 3 - 6 Manual English RadioFans.CN 收音机爱 好者资料库 Subject to change without notice 2 Contents General information regarding the CE marking . 4 General Information . 6 Symbols. 6 General Information . 6 Use of tilt handle . 6 Safety . 6 Intended purpose and operating condit

2、ions . 6 Warranty . 7 Maintenance. 7 Protective Switch-Off. 7 Power supply. 7 Type of signal voltage. 8 Amplitude Measurements . 8 Voltage values of a sine curve . 8 Total value of input voltage . 9 Time Measurements . 9 Connection of Test Signal . 10 First Time Operation . 11 Trace Rotation TR. 11

3、Probe compensation and use . 11 Adjustment at 1kHz. 11 Adjustment at 1MHz . 12 Operating modes of the vertical amplifiers . 12 X-Y Operation . 13 Phase comparison with Lissajous figures . 13 Phase difference measurement. 13 in DUAL mode . 13 Phase difference measurement in DUAL mode. 14 Measurement

4、of an amplitude modulation . 14 Triggering and time base . 14 Automatic Peak (value) - Triggering . 15 Normal Triggering. 15 Slope. 15 Trigger coupling. 15 Line triggering () . 16 Alternate triggering . 16 External triggering . 16 Trigger indicator . 16 Holdoff-time adjustment . 16 Component Tester.

5、 17 General . 17 Using the Component Tester. 17 Test Procedure . 17 Test Pattern Displays . 17 Testing Resistors . 17 Testing Capacitors and Inductors . 17 Testing Semiconductors . 18 Testing Diodes . 18 Testing Transistors . 18 In-Circuit Tests . 18 Front Panel Elements HM 303-6 (Brief Description

6、- Front View). 20 Short Instruction for HM303-6 . 22 Oscilloscope HM 303-6 3 RadioFans.CN 收音机爱 好者资料库 3 Subject to change without notice General information regarding the CE marking HAMEG instruments fulfi ll the regulations of the EMC directive. The conformity test made by HAMEG is based on the actu

7、al generic- and product stan- dards. In cases where different limit values are applicable, HAMEG applies the severer standard. For emission the limits for residential, commercial and light industry are applied. Regarding the immunity (susceptibility) the limits for industrial environment have been u

8、sed. The measuring- and data lines of the instrument have much infl uence on emmission and immunity and therefore on meeting the acceptance limits. For different applications the lines and/or cables used may be different. For measurement operation the following hints and conditions regarding emissio

9、n and immunity should be observed: 1. Data cables For the connection between instruments resp. their interfaces and external devices, (computer, printer etc.) suffi ciently screened cables must be used. Without a special instruction in the manual for a reduced cable length, the maximum cable length

10、of a dataline must be less than 3 meters and not be used outside buildings. If an interface has several connectors only one connector must have a connection to a cable. Basically interconnections must have a double screening. For IEEE-bus purposes the double screened cables HZ72S and HZ72L from HAME

11、G are suitable. 2. Signal cables Basically test leads for signal interconnection between test point and instrument should be as short as possible. Without instruction in the manual for a shorter length, signal lines must be less than 3 meters and not be used outside buildings. Signal lines must scre

12、ened (coaxial cable - RG58/U). A proper ground connection is required. In combination with signal generators double screened cables (RG223/U, RG214/U) must be used. 3. Infl uence on measuring instruments. Under the presence of strong high frequency electric or magnetic fi elds, even with careful set

13、up of the measuring equipment an infl uence of such signals is unavoidable. This will not cause damage or put the instrument out of operation. Small deviations of the measuring value (reading) exceeding the instruments spe- cifi cations may result from such conditions in individual cases. 4. RF immu

14、nity of oscilloscopes. 4.1 Electromagnetic RF fi eld The infl uence of electric and magnetic RF fi elds may become visible (e.g. RF superimposed), if the fi eld intensity is high. In most cases the coupling into the oscilloscope takes place via the device under test, mains/line supply, test leads, c

15、ontrol cables and/or radiation. The device under test as well as the oscilloscope may be effected by such fi elds. Although the interior of the oscilloscope is screened by the cabinet, direct radiation can occur via the CRT gap. As the bandwidth of each amplifi er stage is higher than the total 3dB

16、bandwidth of the oscilloscope, the infl uence RF fi elds of even higher frequencies may be noticeable. 4.2 Electrical fast transients / electrostatic discharge Electrical fast transient signals (burst) may be coupled into the oscilloscope directly via the mains/line supply, or indirectly via test le

17、ads and/or control cables. Due to the high trigger and input sensitivity of the oscilloscopes, such normally high signals may effect the trigger unit and/or may become visible on the CRT, which is unavoidable. These effects can also be caused by direct or indirect electrostatic discharge. KONFORMITT

18、SERKLRUNG DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE Hersteller HAMEG Instruments GmbH Manufacturer Industriestrae 6 Fabricant D-63533 Mainhausen Die HAMEG GmbH bescheinigt die Konformitt fr das Produkt The HAMEG GmbH herewith declares conformity of the product HAMEG GmbH dclare la conformi

19、te du produit Bezeichnung / Product name / Designation: Oszilloskop/Oscilloscope/Oscilloscope Typ / Type / Type: HM303-6 mit / with / avec: Optionen / Options / Options: mit den folgenden Bestimmungen / with applicable regulations / avec les directives suivantes EMV Richtlinie 89/336/EWG ergnzt durc

20、h 91/263/EWG, 92/31/EWG EMC Directive 89/336/EEC amended by 91/263/EWG, 92/31/EEC Directive EMC 89/336/CEE amende par 91/263/EWG, 92/31/CEE Niederspannungsrichtlinie 73/23/EWG ergnzt durch 93/68/EWG Low-Voltage Equipment Directive 73/23/EEC amended by 93/68/EEC Directive des equipements basse tensio

21、n 73/23/CEE amende par 93/68/CEE 15.01.2001 Angewendete harmonisierte Normen / Harmonized standards applied / Normes harmonises utilises Sicherheit / Safety / Scurit EN 61010-1: 1993 / IEC (CEI) 1010-1: 1990 A 1: 1992 / VDE 0411: 1994 EN 61010-1/A2: 1995 / IEC 1010-1/A2: 1995 / VDE 0411 Teil 1/A1: 1

22、996-05 berspannungskategorie / Overvoltage category / Catgorie de surtension: II Verschmutzungsgrad / Degree of pollution / Degr de pollution: 2 Elektromagnetische Vertrglichkeit / Electromagnetic compatibility / Compatibilit lectromagntique EN 61326-1/A1 Straussendung / Radiation / Emission: Tabell

23、e / table / tableau 4; Klasse / Class / Classe B. Strfestigkeit / Immunity / Imunitee: Tabelle / table / tableau A1. EN 61000-3-2/A14 Oberschwingungsstrme / Harmonic current emissions / missions de courant harmoni- que: Klasse / Class / Classe D. EN 61000-3-3 Spannungsschwankungen u. Flicker / Volta

24、ge fl uctuations and fl icker / Fluctuations de tension et du fl icker. Datum /Date /Date Unterschrift / Signature /Signatur E. Baumgartner Technical Manager /Directeur Technique HAMEG Instruments GmbH General information regarding the CE marking RadioFans.CN 收音机爱 好者资料库 Subject to change without not

25、ice 4 HM303-6 3 5 M H z A n a l o g O s c i l l o s c o p e H M 3 0 3 - 6 Maximum signal fidelity with minimum overshoot 2 Channels with deflection coefficients of 1mV 20V/cm, Low Noise Amplifiers Time Base 0.2s 100ns/cm, with X Magnification to 10ns/cm Triggering from 0 to 50MHz from 5mm signal lev

26、el (100MHz 8mm) Analog mode provides unexcelled signal presentation at high resolution and up to 500,000 signal displays/sec. Yt, XY and component-test modes Line triggered composite video signal No signal distortion resulting from overshoot Full screen display of 35MHz sine wave signal 5 Subject to

27、 change without notice 35 MHz Analog Oscilloscope HM303-6 Valid at 23 C after a 30 minute warm-up period Vertical Deflection Operating Modes:Channel I or II only Channels I and II (alternate or chopped) Sum or Difference of CH I and CH II Invert:CH II XY Mode:via CH I (X) and CH II (Y) Bandwidth:2 x

28、 0 to 35MHz (-3dB) Rise Time:10ns Overshoot:max. 1% Deflection Coefficients: 1-2-5 Sequence 1mV/div. 2mV/div.: 5% (Bandwidth 0 10MHz (-3dB) 5mV/div. 20V/div.: 3% (Bandwidth 0 35MHz (-3dB) Variable (uncalibrated): 2.5 : 1 to 50V/div. Input Impedance:1M II 20pF Input Coupling:DC, AC, GND (ground) Max.

29、 Input Voltage: 400V (DC + peak AC) Triggering Automatic (Peak to Peak): 20Hz 50MHz (5mm) 50MHz - 100MHz (8mm) Normal with Level Control:0 - 50MHz(5mm) 50MHz 100MHz ( 8mm) Trigger Indicator: LED Slope:positive or negative Sources:Channel I or II, CH I / CH II alternate ( 8mm), Line and External Coup

30、ling:AC: 10Hz 100MHz DC: 0 100MHz LF: 0 1.5kHz Trigger Indicator:LED External Trigger Signal:0.3Vpp(30Hz 50MHz) Active TV sync. separator:pos. and neg. Horizontal Deflection Time Base:0.2s/div. 0.1s/div. (1-2-5 Sequence) Accuracy:3% Variabel (uncalibrated): 2.5:1 to 0.5s/div. X Magnification x 10:up

31、 to 10ns/div. Accuracy: 5% Hold-Off Time:variable to approx. 10 : 1 XY Bandwidth X Amplifier: 0 2.5MHz (-3 dB) XY Phase shift 3:120kHz Component Tester Test Voltage:approx. 7Vrms(open circuit) Test Current:max. 7mArms(short-circuit) Test Frequency:approx. 50Hz Test Connection:2 banana jacks 4mm One

32、test circuit lead is grounded via protective earth (PE) Miscellaneous CRT:D14-363GY, 8 x 10cm with internal graticule Acceleration Voltage:approx. 2kV Trace Rotation: adjustable on front panel Calibrator Signal (Square Wave): 0.2V 1%, 1kHz/1MHz (tr 4ns) Power Supply (Mains):105 253V, 50/60Hz 10%, CA

33、T II Power Consumption:approx. 36 Watt at 230V/50Hz Ambient temperature: 0C.+40C Safety class:Safety class I (EN61010-1) Weight:approx. 5.4kg Dimensions (W x H x D):285 x 125 x 380mm Accessories supplied: Line Cord, operators manual, 2 Probes 1:1 / 10:1 (HZ154) HM303-6E/260107/ce Subject to alterati

34、ons HAMEG Instruments GmbH Registered Trademark DQS-certified in accordance with DIN EN ISO 9001:2000, Reg.-No.: DE-071040 QM HAMEG Instruments GmbH Industriestr. 6 D-63533 Mainhausen Tel +49(0)6182 8000 Fax +49(0)6182 800100 w w w. h a m e g . co m Specifi cations Subject to change without notice 6

35、 Safe operation may be endangered if any of the following was noticed: in case of visible damage. in case loose parts were noticed if it does not function any more. after prolonged storage under unfavourable conditions (e.g. like in the open or in moist atmosphere). after any improper transport (e.g

36、. insuffi cient packing not conforming to the minimum standards of post, rail or transport company) Proper operation Please note: This instrument is only destined for use by personnel well instructed and familiar with the dangers of electrical mea- surements. For safety reasons the oscilloscope may

37、only be operated from mains outlets with safety ground connector. It is prohibited to separate the safety ground connection. The plug must be inserted prior to connecting any signals. General information Please check the instrument for mechanical damage or loose parts immediately after unpacking. In

38、 case of damage we advise to contact the sender. Do not operate. List of symbols used Consult the manual High voltage Important note Ground Positioning the instrument As can be seen from the fi gures, the handle can be set into diffe- rent positions: A = carrying B = handle removal and horizontal ca

39、rrying C = horizontal operating D and E = operating at different angles F = handle removal T = shipping (handle unlocked) Attention! When changing the handle position, the instru- ment must be placed so that it can not fall (e.g. placed on a table). Then the handle locking knobs must be simultaneous

40、ly pulled outwards and rotated to the required position. Without pulling the locking knobs they will latch in into the next locking position. Handle mounting/dismounting The handle can be removed by pulling it out further, depending on the instrument model in position B or F. Safety The instrument fulfi ls the VDE 0411 part 1 regulations for electrical measuring, control and laboratory instruments and was manufactured and tested accordingly. It left the factory in perfect safe condition. Hence it also corresponds to