EMG_Humbucker_Wiring_Diagrams 电路图.pdf

《EMG_Humbucker_Wiring_Diagrams 电路图.pdf》由会员分享，可在线阅读，更多相关《EMG_Humbucker_Wiring_Diagrams 电路图.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTALLATION INFORMATION All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If upon examination the pickup is determined to be defective, a replacement will be made at no charge. Warranty replac

2、ement products are covered by this same warranty. This warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable. Warranty: Copyright EMG Inc. 2007 EMG Models: EMG-H, HA, 58, 60, 60A, 81, 85 SPECIFICATIONS: MODEL: Logo Color White Gold Gold

3、Grey Gold Silver Gold Resonant Frequency (KHz) 4.95 4.45 1.90 2.90 2.20 2. 2.00 2.45 Output Voltage (String) 1.01.0 2.8 1.25 1. 1.25 2.0 2.1 Output Voltage (Strum) 1.50 1.50 4.0 3.53.75 4.5 4.5 Output Noise 60Hz -90 -91 -91 - 8 9 - 91 - 91 -89 Output Impedance (Kohm) 10 10 Current 9V (Microamps) 80

4、80 Battery Life (Hours) 3000 3000 3000 3000 3000 3000 3000 Maximum Supply (Volts DC) 27 27 H HA 60 60A 81 85 58 IMPORTANT INSTALLATION NOTES: 1) Only one battery is required for the pickups, and any active accessories such as the SPC, RPC, EXG, AB, PA-2, and Pi-2. 2) Use an Alkaline or Lithium batte

5、ry for longest life. 3) The controls included with EMG Systems are 25K Ohm, Audio Taper. This value of control is required for the system to work correctly. 4) When installing EMG Active Pickups, DO NOT connect the bridge ground wire. This wire is usually soldered to a volume or tone control casing

6、and goes to the bridge. This wire grounds the strings and uses them and your body as a shield against hum and buzz. It also creates a shock hazard. EMG Pickups are shielded internally and DO NOT require string grounding. This greatly reduces the possibility of reverse polarity shock from microphones

7、 and other equipment 5) EMG Active Pickups have very little magnetism compared to passive pickups. We recommend you adjust the pickups as close to the strings as possible. Sustain and string movement will not be inhibited by close adjustment. 6) If your installation is different from the diagrams in

8、 these instructions or you need additional diagrams visit our website: for a complete listing of available diagrams. 10 10 10 10 10 80 80 80 80 80 27 27 27 27 27 Magnet Type C A A/S C A C/S A Notes: Magnet Type: A (Alnico) A/S (Alnico/Steel) C (Ceramic) C/S (Ceramic/Steel) Updated 1/10/07 RadioFans.

9、CN 收音机爱 好者资料库 Be sure to unplug your guitar when not in use to avoid current drain on the battery! The diagrams shown are for EMG Active Pickups only. All diagrams show the Red Wire coming from the pickups connected to the battery. If you are installing EMG-HZ Passive Pickups refer to those diagrams

10、. The Red Wire of the HZ Pickup is NOT for battery power, it is a coil wire. Gibson Les Paul Guitars manufactured after April of 1975 have a shield can installed in the control compartment and use long shaft pots. Long shaft 25K pots are available from your dealer or EMG. Refer to diagram 7 for this

11、 wiring. Refer to the following diagrams for the volume, tone configuration foryour guitar and follow that diagram. Its recommended that if you plan to install EMG Products that you do the installation per the diagrams included here and get your guitar working before adding accessories. We recommend

12、 you make a simple diagram of your current wiring scheme and follow it when rewiring with the EMG 25K Controls. Installation Procedures for Models: EMG Models: EMG-H, HA, 58, 60, 60A, 81, 85 1) Disconnect the existing pickup from its volume and tone control. 2) Disconnect any existing selection swit

13、ch wire(s) from its volume and tone control. 3) Remove the pickup and the volume and tone control. Place the EMG volume and tone control in the instrument. Mount the pickup in the mounting ring and install the quick connect cable as shown in the diagram and route the cable to the control cavity. 4)

14、Solder the braid of the pickup cable to the case of the volume control as shown in the diagram and connect the switch wires as shown. 5) For two-pickup guitars, follow steps 1-4 before continuing. 6) Remove the existing output jack and replace it with the EMG output jack. Solder the output wire to t

15、he jack as shown in the diagram. 7) Solder the RED wire(s) of the pickup(s) to the RED wire of the battery clip and cover the connection with the heat shrink tubing provided. 8) Use some of the packaging foam that comes with the pickup and surround the battery to insulate it. Place the battery on th

16、e clip and place it securely in the control cavity. 9) We suggest you test the guitar before closing up the control cavity to make sure everything is working. SPECIAL NOTE: RadioFans.CN 收音机爱 好者资料库 Bottom View Red Black White Black Solder Pickup Braids to pot casings 2 Volume (Independent) 2 Tone w/

17、Gibson Style Toggle Switch Red wires from Pickups Volume Pickup Output Cable Solder Fingerboard Pickup Hot lead to this lug .1uf 104 Tone Volume Pickup Output Cable Solder Bridge Pickup Hot lead to this lug .1uf 104 Tone RadioFans.CN 收音机爱 好者资料库 Bottom View Red Black White Black Solder Pickup Braids

18、to pot casings 2 Volume (Either volume will act as master) w/ selection switch in middle position) 2 Tone w/ Gibson Style Toggle Switch Red wires from Pickups Volume Pickup Output Cable Solder Fingerboard Pickup Hot lead to this lug .1uf 104 Tone Volume Pickup Output Cable Solder Bridge Pickup Hot lead to this lug .1uf 104 Tone Tone Tone Volume Volume .1 .1 RED Bottom View Bridge pickup cable (Gibson Les Paul April 1975 and later) Cable from 3 way switch Finger Board pickup cable RED FROM PICKUPS BLACK BLACK Black wire/ Green wire shrink tubing. GREEN WHITE BLACK RED