Floyd_Rose_Locking_Tremelo_Instructions 电路图.pdf

《Floyd_Rose_Locking_Tremelo_Instructions 电路图.pdf》由会员分享，可在线阅读，更多相关《Floyd_Rose_Locking_Tremelo_Instructions 电路图.pdf（1页珍藏版）》请在收音机爱好者资料库上搜索。

1、Changing Strings Loosen strings completely by turning machine heads. Loosen the string lock thumb screws counter clockwise on the back of the Sperzel gears. You only need to turn these screws about 2 or 3 turns. Loosen saddle lock screws with 3mm allen wrench. Remove strings. Remove broken string bi

2、ts from lock box with small magnetic screwdriver or long nose tweezers. Normalize the tremolo fine tuners to the mid point of their travel. Cut ball ends and extra wraps off of the new strings. Insert new strings into lock box, sandwiched between lock box wall and lock block. Tighten saddle lock scr

3、ews real snug, but do not over tighten them. Slide string through the small hole in the string post. Take up all the slack then tighten the thumb screw on the back. Cut off the excess string and then tune your guitar. Tune up from low E (6th) string to high E (1st) string, 6 or 7 times in order to s

4、tretch the tremolo springs. Stretch your strings using the tremolo arm. When strings hold their pitch relative to each other, then tuning is complete. Fine tune using the fine tuners. Lock Block Arm Cap Nut Attaching Arm: Slide tremolo arm into socket. Turn the arm cap nut clockwise about 4 turns un

5、til it stops. If you want your arm to stay up then tighten the cap nut fairly tight. If you want your arm to swing freely then back off slightly on the cap nut. Remove arm when transporting or storing guitar in its case. Oil socket with a drop of 3 in 1 oil twice a year or more. Overall String Heigh

6、t Adjustment: Turn string height studs C.W. to lower action. Turn string height studs C.C.W. to raise action. Spring Tension Adjustment: Your Carvin guitar comes set up with a set of high quality 942 strings. If you continue to use the same brand and gage of strings, spring tension adjustment is nor

7、mally not necessary. However, if you switch brands or gages you may need to re- adjust spring tension. Follow the steps below. 1. Tune up guitar to pitch. 2. Remove rear cover plate. 3.If tremolo rear end is to high in the air follow steps #4,5,6 & 11. 4. Tighten the two screws on the rear of the gu

8、itar that hold the spring claw, 1/2turn each with a phillips #2 driver. 5. Re-tune guitar and see if tremolo is parallel with guitar body. 6. If its just right, go to step #11. If its still to high repeat steps #4 & 5. 7. If tremolo rear end is setting to low in the tremolo cavity follow steps #8, 9

9、, & 10. 8. Loosen the two screws that hold the spring claw, 1/2turn each with a phillips #2 driver. 9. Re-tune and see if tremolo is parallel with guitar body. 10. If it is just right, go to step #11. If its still to low repeat steps #8 & 9. 11. Put rear cover plate back on. Tips: When turning the t

10、wo claw screws, have your guitar face down on a padded table. Hold screw driver firmly when turning, so as not to slip off screw head and scratch the back of your guitar. Instructions for “Original” Floyd Rose Locking Tremolo 800-854-2235 or Saddle Lock Screws (3mm wrench) Intonation Screws (2.5mm w

11、rench) Tips: Dont rest palm on tremolo while tuning up or fine tuning. Over tightening of saddle lock screws can cause: Lock box walls to crack, distortion of shape of the lock block, rounding of allen sockets, and, or cause rapid string breakage. When stringing up the Sperzel tuners do not wrap mul

12、tiple string wraps around the post. Eliminate as many wraps as possible to keep your guitar in better tune. 1/2 of a turn around the string post should be considered maximum. Saddle Lock Box Fine Tuners String height Studs (3mm wrench) The Original Floyd Rose is the most rugged and dependable lockin

13、g tremolo made today. With replacement parts available at most guitar repair shops, the serviceability and playability cant be beat, and will stay that way for years to come. Rear Tremolo Cavity Adjustment Screws (use #2 phillips screwdriver) Spring ClawSpringsTremolo Sustain Block If the arm socket becomes loose, tighten with a 3mm allen wrench. RadioFans.CN 收音机爱 好者资料库