KEI 2010 User 电路图.pdf

《KEI 2010 User 电路图.pdf》由会员分享，可在线阅读，更多相关《KEI 2010 User 电路图.pdf（278页珍藏版）》请在收音机爱好者资料库上搜索。

1、Model 2010Multimeter Users Manual A G R E A T E RM E A S U R E O F C O N F I D E N C E RadioFans.CN 收音机爱 好者资料库 WARRANTY Keithley Instruments, Inc. warrants this product to be free from defects in material and workmanship for a period of 3 years from date of shipment. Keithley Instruments, Inc. warra

2、nts the following items for 90 days from the date of shipment: probes, cables, rechargeable batteries, diskettes, and documentation. During the warranty period, we will, at our option, either repair or replace any product that proves to be defective. To exercise this warranty, write or call your loc

3、al Keithley representative, or contact Keithley headquarters in Cleveland, Ohio. You will be given prompt assistance and return instructions. Send the product, transportation prepaid, to the indicated service facility. Repairs will be made and the product returned, transportation prepaid. Repaired o

4、r replaced products are warranted for the balance of the original warranty period, or at least 90 days. LIMITATION OF WARRANTY This warranty does not apply to defects resulting from product modifi cation without Keithleys express written consent, or misuse of any product or part. This warranty also

5、does not apply to fuses, software, non-rechargeable batteries, damage from battery leakage, or problems arising from normal wear or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR

6、 A PARTICULAR USE. THE REMEDIES PROVIDED HEREIN ARE BUYERS SOLE AND EXCLUSIVE REMEDIES. NEITHER KEITHLEY INSTRUMENTS, INC. NOR ANY OF ITS EMPLOYEES SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF ITS INSTRUMENTS AND SOFTWARE EVEN IF KE

7、ITHLEY INSTRUMENTS, INC., HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SUCH EXCLUDED DAMAGES SHALL INCLUDE, BUT ARE NOT LIMITED TO: COSTS OF REMOVAL AND INSTALLATION, LOSSES SUSTAINED AS THE RESULT OF INJURY TO ANY PERSON, OR DAMAGE TO PROPERTY. Keithley Instruments, Inc. 28775 Au

8、rora Road Cleveland, Ohio 44139 440-248-0400 Fax: 440-248-6168 1-888-KEITHLEY (534-8453) Sales Offi ces: BELGIUM: Bergensesteenweg 709 B-1600 Sint-Pieters-Leeuw 02-363 00 40 Fax: 02-363 00 64 CHINA: Yuan Chen Xin Building, Room 705 12 Yumin Road, Dewai, Madian Beijing 100029 8610-82251886 Fax: 8610-

9、82251892 FINLAND: Halsuantie 2 00420 Helsinki, Finland 09-53 06 65 60 Fax: 09-53 06 65 65 FRANCE: 3, alle des Garays 91127 Palaiseau Cdex 01-64 53 20 20 Fax: 01-60 11 77 26 GERMANY: Landsberger Strasse 65 82110 Germering 089-84 93 07-40 Fax: 089-84 93 07-34 GREAT BRITAIN: Unit 2 Commerce Park, Brune

10、l Road Theale, Berkshire RG7 4AB 0118 -929 75 00 Fax: 0118- 929 75 19 INDIA: 1/5, Eagles Street Langford Town Bangalore 560 025 080 212 80-27 Fax: 080 212 80 05 ITALY: Viale San Gimignano, 38 20146 Milano 02-48 39 16 01 Fax: 02-48 30 22 74 JAPAN: New Pier Takeshiba North Tower 13F 11-1, Kaigan 1-cho

11、me Minato-ku, Tokyo 105-0022 81-3-5733-7555 Fax: 81-3-5733-7556 KOREA: 2FL., URI Building 2-14 Yangjae-Dong Seocho-Gu, Seoul 137-888 82-2-574-7778 Fax: 82-2-574-7838 NETHERLANDS: Postbus 559 4200 AN Gorinchem 0183-63 53 33 Fax: 0183-63 08 21 SWEDEN: c/o Regus Business Centre Frosundaviks All 15, 4tr

12、 16970 Solna 08-50 90 46 00 Fax: 08-655 26 10 TAIWAN: 13F-3, NO. 6, Lane 99, Pu-Ding Road, Hsinchu, Taiwan, ROC. 886-3-572-9077 Fax: 886-3-572-9031 5/03 RadioFans.CN 收音机爱 好者资料库 Model 2010 Multimeter Users Manual 1996, Keithley Instruments, Inc. All rights reserved. Cleveland, Ohio, U.S.A. Fifth Prin

13、ting, August 2003 Document Number: 2010-900-01 Rev. E RadioFans.CN 收音机爱 好者资料库 Manual Print History The print history shown below lists the printing dates of all Revisions and Addenda created for this manual. The Revision Level letter increases alphabetically as the manual undergoes subsequent update

14、s. Addenda, which are released between Revisions, contain important change information that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new Revision is created, all Addenda associated with the previous Revision of the manual are incorporated int

15、o the new Revision of the manual. Each new Revision includes a revised copy of this print history page. Revision A (Document Number 2010-900-01).January 1996 Revision B (Document Number 2010-900-01).February 1996 Addendum B (Document Number 2010-900-02). September 1996 Revision C (Document Number 20

16、10-900-01).June 1998 Revision D (Document Number 2010-900-01).April 1999 Revision E (Document Number 2010-900-01) .August 2003 All Keithley product names are trademarks or registered trademarks of Keithley Instruments, Inc. Other brand names are trademarks or registered trademarks of their respectiv

17、e holders. The following safety precautions should be observed before using this product and any associated instrumentation. Although some instruments and accessories would normally be used with non-hazardous voltages, there are situations where hazardous conditions may be present. This product is i

18、ntended for use by qualifi ed personnel who recognize shock hazards and are familiar with the safety precautions required to avoid possible injury. Read and follow all installation, operation, and maintenance information carefully before using the product. Refer to the manual for complete product sp

19、ecifi cations. If the product is used in a manner not specifi ed, the protection provided by the product may be impaired. The types of product users are: Responsible body is the individual or group responsible for the use and maintenance of equipment, for ensuring that the equip- ment is operated wi

20、thin its specifi cations and operating limits, and for ensuring that operators are adequately trained. Operators use the product for its intended function. They must be trained in electrical safety procedures and proper use of the instrument. They must be protected from electric shock and contact wi

21、th hazardous live circuits. Maintenance personnel perform routine procedures on the product to keep it operating properly, for example, setting the line voltage or replacing consumable materials. Maintenance procedures are described in the manual. The procedures explicitly state if the operator may

22、perform them. Otherwise, they should be performed only by service personnel. Service personnel are trained to work on live circuits, and perform safe installations and repairs of products. Only properly trained service personnel may perform installation and service procedures. Keithley products are

23、designed for use with electrical signals that are rated Measurement Category I and Measurement Category II, as described in the International Electrotechnical Commission (IEC) Standard IEC 60664. Most measurement, control, and data I/O signals are Measurement Category I and must not be directly conn

24、ected to mains voltage or to voltage sources with high transient over-voltages. Measurement Category II connections require protection for high transient over-voltages often associated with local AC mains connections. Assume all measurement, control, and data I/O connections are for connection to Ca

25、tegory I sources unless otherwise marked or described in the Manual. Exercise extreme caution when a shock hazard is present. Lethal voltage may be present on cable connector jacks or test fi xtures. The American National Standards Institute (ANSI) states that a shock hazard exists when voltage leve

26、ls greater than 30V RMS, 42.4V peak, or 60VDC are present. A good safety practice is to expect that hazardous voltage is present in any unknown circuit before measuring. Operators of this product must be protected from electric shock at all times. The responsible body must ensure that operators are

27、prevented access and/or insulated from every connection point. In some cases, connections must be exposed to potential human contact. Product operators in these circumstances must be trained to protect themselves from the risk of electric shock. If the circuit is capable of operating at or above 100

28、0 volts, no conductive part of the circuit may be exposed. Do not connect switching cards directly to unlimited power circuits. They are intended to be used with impedance limited sources. NEVER connect switching cards directly to AC mains. When connecting sources to switching cards, install protect

29、ive devices to limit fault current and voltage to the card. Before operating an instrument, make sure the line cord is connected to a properly grounded power receptacle. Inspect the connecting cables, test leads, and jumpers for possible wear, cracks, or breaks before each use. When installing equip

30、ment where access to the main power cord is restricted, such as rack mounting, a separate main input power disconnect device must be provided, in close proximity to the equipment and within easy reach of the operator. S afety Precautions 5/03 For maximum safety, do not touch the product, test cables

31、, or any other instruments while power is applied to the circuit under test. ALWAYS remove power from the entire test system and discharge any capacitors before: connecting or disconnecting cables or jumpers, installing or removing switching cards, or making internal changes, such as installing or r

32、emoving jumpers. Do not touch any object that could provide a current path to the common side of the circuit under test or power line (earth) ground. Always make measurements with dry hands while standing on a dry, insulated surface capable of withstanding the voltage being measured. The instrument

33、and accessories must be used in accordance with its specifi cations and operating instructions or the safety of the equipment may be impaired. Do not exceed the maximum signal levels of the instruments and accessories, as defi ned in the specifi cations and operating information, and as shown on the

34、 instrument or test fi xture panels, or switching card. When fuses are used in a product, replace with same type and rating for continued protection against fi re hazard. Chassis connections must only be used as shield connections for measuring circuits, NOT as safety earth ground connections. If yo

35、u are using a test fi xture, keep the lid closed while power is applied to the device under test. Safe operation requires the use of a lid interlock. If a screw is present, connect it to safety earth ground using the wire recommended in the user documentation. The symbol on an instrument indicates t

36、hat the user should refer to the operating instructions located in the manual. The symbol on an instrument shows that it can source or measure 1000 volts or more, including the combined effect of normal and common mode voltages. Use standard safety precautions to avoid personal contact with these vo

37、ltages. The symbol indicates a connection terminal to the equipment frame. The WARNING heading in a manual explains dangers that might result in personal injury or death. Always read the associated information very carefully before performing the indicated procedure. The CAUTION heading in a manual

38、explains hazards that could damage the instrument. Such damage may invalidate the warranty. Instrumentation and accessories shall not be connected to humans. Before performing any maintenance, disconnect the line cord and all test cables. To maintain protection from electric shock and fi re, replace

39、ment components in mains circuits, including the power transformer, test leads, and input jacks, must be purchased from Keithley Instruments. Standard fuses, with applicable national safety approvals, may be used if the rating and type are the same. Other components that are not safety related may b

40、e purchased from other suppliers as long as they are equivalent to the original component. (Note that selected parts should be purchased only through Keithley Instruments to maintain accuracy and functionality of the product.) If you are unsure about the applicability of a replacement component, cal

41、l a Keithley Instruments offi ce for information. To clean an instrument, use a damp cloth or mild, water based cleaner. Clean the exterior of the instrument only. Do not apply cleaner directly to the instrument or allow liquids to enter or spill on the instrument. Products that consist of a circuit

42、 board with no case or chassis (e.g., data acquisition board for installation into a computer) should never require cleaning if handled accord- ing to instructions. If the board becomes contaminated and operation is affected, the board should be returned to the factory for proper cleaning/servicing.

43、 ! Table of Contents 1General Information Introduction . 1-2 Feature overview . 1-2 Warranty information . 1-3 Manual addenda . 1-3 Safety symbols and terms . 1-3 Specifications . 1-3 Inspection . 1-4 Options and accessories . 1-4 Scanner cards . 1-4 General purpose probes . 1-4 Low thermal probes . 1-5 Cables and adapters . 1-5 Rack mount kits . 1-6 Carrying case . 1-6 2Basic Measurements Introduction . 2-2 Front panel summary . 2-3 Rear panel summary . 2-6 Power-up . 2-8 Line power connection . 2-8 Setting line voltage and replacing fuse . 2