KEI 7001 Quick Reference Guide 电路图.pdf

《KEI 7001 Quick Reference Guide 电路图.pdf》由会员分享，可在线阅读，更多相关《KEI 7001 Quick Reference Guide 电路图.pdf（42页珍藏版）》请在收音机爱好者资料库上搜索。

1、Model 7001Switch System Quick Reference Guide A G R E A T E RM E A S U R E O F C O N F I D E N C E RadioFans.CN 收音机爱 好者资料库 Model 7001 Switch System Quick Reference Guide 1992, Keithley Instruments, Inc. All rights reserved. Cleveland, Ohio, U.S.A. Document Number: 7001-903-01 Rev. A RadioFans.CN 收音机

2、爱 好者资料库 Table of Contents Safety Precautions. 1 Introduction . 5 Operation Summary. 6 Menu Structures.11 Default Conditions. 16 Error and Status Messages . 19 IEEE-488.2 Common Commands and Queries. 25 SCPI Command Subsystems . 27 RadioFans.CN 收音机爱 好者资料库 1 Safety Precautions The following safety pre

3、cautions should be observed before using this product and any associated instrumentation. Al- though some instruments and accessories would normally be used with non-hazardous voltages, there are situations where hazardous conditions may be present. This product is intended for use by qualifi ed per

4、sonnel who recognize shock hazards and are familiar with the safety pre- cautions required to avoid possible injury. Read the operat- ing information carefully before using the product. The types of product users are: Responsible body is the individual or group responsible for the use and maintenanc

5、e of equipment, for ensuring that the equipment is operated within its specifi cations and operating limits, and for ensuring that operators are adequately trained. Operators use the product for its intended function. They must be trained in electrical safety procedures and proper use of the instrum

6、ent. They must be protected from electric shock and contact with hazardous live circuits. Maintenance personnel perform routine procedures on the product to keep it operating, for example, setting the line voltage or replacing consumable materials. Maintenance procedures are described in the manual.

7、 The procedures ex- plicitly state if the operator may perform them. Otherwise, they should be performed only by service personnel. Service personnel are trained to work on live circuits, and perform safe installations and repairs of products. Only properly trained service personnel may perform inst

8、allation and service procedures. Keithley products are designed for use with electrical signals that are rated Installation Category I and Installation Catego- ry II, as described in the International Electrotechnical Com- mission (IEC) Standard IEC 60664. Most measurement, control, and data I/O sig

9、nals are Installation Category I and must not be directly connected to mains voltage or to voltage sources with high transient over-voltages. Installation Cate- gory II connections require protection for high transient 2 over-voltages often associated with local AC mains connec- tions. The user shou

10、ld assume all measurement, control, and data I/O connections are for connection to Category I sources unless otherwise marked or described in the Manual. Exercise extreme caution when a shock hazard is present. Lethal voltage may be present on cable connector jacks or test fi xtures. The American Na

11、tional Standards Institute (ANSI) states that a shock hazard exists when voltage levels greater than 30V RMS, 42.4V peak, or 60VDC are present. A good safety practice is to expect that hazardous voltage is present in any unknown circuit before measuring. Users of this product must be protected from

12、electric shock at all times. The responsible body must ensure that users are prevented access and/or insulated from every connection point. In some cases, connections must be exposed to poten- tial human contact. Product users in these circumstances must be trained to protect themselves from the ris

13、k of electric shock. If the circuit is capable of operating at or above 1000 volts, no conductive part of the circuit may be exposed. Do not connect switching cards directly to unlimited power circuits. They are intended to be used with impedance limit- ed sources. NEVER connect switching cards dire

14、ctly to AC mains. When connecting sources to switching cards, install protective devices to limit fault current and voltage to the card. Before operating an instrument, make sure the line cord is connected to a properly grounded power receptacle. Inspect the connecting cables, test leads, and jumper

15、s for possible wear, cracks, or breaks before each use. When installing equipment where access to the main power cord is restricted, such as rack mounting, a separate main in- put power disconnect device must be provided, in close prox- imity to the equipment and within easy reach of the operator. F

16、or maximum safety, do not touch the product, test cables, or any other instruments while power is applied to the circuit under test. ALWAYS remove power from the entire test sys- tem and discharge any capacitors before: connecting or dis- connecting cables or jumpers, installing or removing 3 switch

17、ing cards, or making internal changes, such as install- ing or removing jumpers. Do not touch any object that could provide a current path to the common side of the circuit under test or power line (earth) ground. Always make measurements with dry hands while standing on a dry, insulated surface cap

18、able of with- standing the voltage being measured. The instrument and accessories must be used in accordance with its specifi cations and operating instructions or the safety of the equipment may be impaired. Do not exceed the maximum signal levels of the instruments and accessories, as defi ned in

19、the specifi cations and operat- ing information, and as shown on the instrument or test fi x- ture panels, or switching card. When fuses are used in a product, replace with same type and rating for continued protection against fi re hazard. Chassis connections must only be used as shield connections

20、 for measuring circuits, NOT as safety earth ground connec- tions. If you are using a test fi xture, keep the lid closed while power is applied to the device under test. Safe operation requires the use of a lid interlock. If a screw is present, connect it to safety earth ground using the wire recomm

21、ended in the user documentation. The symbol on an instrument indicates that the user should refer to the operating instructions located in the man- ual. The symbol on an instrument shows that it can source or measure 1000 volts or more, including the combined ef- fect of normal and common mode volta

22、ges. Use standard safety precautions to avoid personal contact with these volt- ages. The WARNING heading in a manual explains dangers that might result in personal injury or death. Always read the as- ! 4 sociated information very carefully before performing the indicated procedure. The CAUTION hea

23、ding in a manual explains hazards that could damage the instrument. Such damage may invalidate the warranty. Instrumentation and accessories shall not be connected to humans. Before performing any maintenance, disconnect the line cord and all test cables. To maintain protection from electric shock a

24、nd fi re, replace- ment components in mains circuits, including the power transformer, test leads, and input jacks, must be purchased from Keithley Instruments. Standard fuses, with applicable national safety approvals, may be used if the rating and type are the same. Other components that are not s

25、afety related may be purchased from other suppliers as long as they are equivalent to the original component. (Note that selected parts should be purchased only through Keithley Instruments to maintain accuracy and functionality of the product.) If you are unsure about the applicability of a replace

26、ment compo- nent, call a Keithley Instruments offi ce for information. To clean an instrument, use a damp cloth or mild, water based cleaner. Clean the exterior of the instrument only. Do not ap- ply cleaner directly to the instrument or allow liquids to enter or spill on the instrument. Products th

27、at consist of a circuit board with no case or chassis (e.g., data acquisition board for installation into a computer) should never require cleaning if handled according to instructions. If the board becomes con- taminated and operation is affected, the board should be re- turned to the factory for p

28、roper cleaning/servicing. All Keithley product names are trademarks or registered trade- marks of Keithley Instruments, Inc. Other brand and product names are trademarks or registered trademarks of their respective holders. 5 Introduction This quick reference guide includes summary informa- tion on

29、front panel and IEEE-488 operation for the Model 7001 Switch System. For detailed information, consult the Model 7001 Instruction Manual. 6 Operation Summary Channel List and Scan List A Channel List specifi es the channels to be closed or opened, and a Scan List specifi es the channels to be scanne

30、d. Each channel in the list is made up of either a two integer CHANNEL number (for non-matrix type cards) or a three integer CHANNEL number (for matrix type cards). Examples: 1!2=Slot 1, Channel 2 2!4=Slot 2, Channel 4 1!2!3=Slot 1, Row 2, Column 3 2!3!6=Slot 2, Row 3, Column 6 Front panel operation

31、 A Channel List is created with the SELECT CHANNELS prompt displayed, and a Scan List is created with the SCAN CHANNELS prompt displayed. The SCAN LIST key toggles the display between the Channel List and the Scan List. Channels are entered into a Channel List and Scan List using the keypad. The fol

32、lowing examples demonstrate proper format. SELECT CHANNELS 1!1, 1!5-1!10, 2!1!1, M1, SCAN CHANNELS 1!10-1!1, 2!1!3, M1, Each entry is separated by a comma (,) which is inserted by pressing the right cursor key () or the ENTER key. Notice that a comma is also used to terminate the list. A channel ran

33、ge is specifi ed by separating the range limits 7 with a hyphen (-). The M1 entry represents a channel pattern that is stored in memory (see STORE and RECALL). Edit keys A list can also be modifi ed by using the edit keys; DELETE and INSERT. A channel entry can be deleted by placing the cursor on th

34、e desired entry and pressing DELETE. To insert an entry, press INSERT (INSERTING ENTRY displayed), place the cursor at the appropriate location, and key in the new entry. Make sure to insert a comma after keying in the channel entry. When fi nished, press INSERT again to cancel the insert function.

35、IEEE-488 bus operation Over the bus, the Channel List is included with the commands that are used to close or open channels. See Closing and Opening Channels. The Scan List is created using the :SCAN command. The following example demonstrates proper format: :SCAN ( 1!10:1!1, 2!1!3, M1) Note that ra

36、nge limits are separated by a colon (:), and the last channel entry in the list is not terminated with a comma. Closing and Opening Channels Front panel operation Channels specifi ed in the Channel List are closed by pressing the CLOSE key. Channels specifi ed in the Channel List are opened by press

37、ing the OPEN key. 8 Note that the OPEN ALL key will open all channels, including those not specifi ed in the Channel List. IEEE-488 bus operation Over the bus, the :CLOSe and :OPEN commands are used to control channels. Note that the Channel List is included with the following examples: :CLOSe ( 1!1

38、, 1!5:1!10, 2!1!1, M1) :OPEN ( 1!1, 1!5:1!10, 2!1!1, M1) Note that a colon (:) is used to separate range limits, and a comma is not used to terminate the list. The following command is analogous to the front panel OPEN ALL key and will simply open all channels: :OPEN ALL Scanning Channels Channels a

39、re scanned in the order that they are pre- sented in the Scan List. Front panel operation To perform a scan, fi rst program the controlling aspects of the scan (see Table 2), and then press STEP to take the Model 7001 out of the idle state (ARM indicator on). Regardless of how the scan is confi gure

40、d, the STEP key is always active allowing you to manually step through the scan. 9 The scan can be terminated at any time by pressing the OPEN ALL key. All closed channels will open and the Model 7001 will return to the idle state (ARM indicator off). IEEE-488 operation Over the bus, a scan is confi

41、 gured using the :TRIGger subsystem commands. Send the following command to take the Model 7001 out of the idle state and begin a scan: :INITiate The scan can be terminated by sending the following command: :ABORt All closed channels will open and the Model 7001 will return to the idle state. Store

42、and Recall Up to 100 channel patterns can be stored in memory. A channel pattern is simply a displayed pattern of open and closed channels. Front panel operation 1. Close the desired channels. 2. Press STORE and enter the desired memory loca- tion (1 to 100). 3. Press ENTER. 10 To recall a channel p

43、attern from memory: 1. Press RECALL and enter the memory location of the stored channel pattern. 2. Press ENTER. The channel status display will imme- diately update to refl ect the recalled channel pat- tern. Another way to recall a channel pattern is to include a memory location (e.g. M36) in a Ch

44、annel List and/or Scan List. In a Channel List, when CLOSE is pressed, the closed channels in the specifi ed channel pattern will close, and when OPEN is pressed, the channels will open. In a Scan List, when the memory location is scanned, the channel status display will update to refl ect the speci

45、fi ed channel pattern. The closed chan- nels in the channel pattern will remain closed unless a different channel pattern is scanned. IEEE-488 bus operation Over the IEEE-488 bus, the :SAVe and :RECall com- mands are used to save (store) and recall channel pat- terns. The following examples demonstr

46、ate proper format: :MEMory:SAVe M36 :MEMory:RECall M36 As in front panel operation, a memory location can be included in the Channel List and/or Scan List. 11 Menu Structures The desired menu is displayed by pressing the appropri- ate key; MENU, SCAN CONFIGURATION or CARD CONFIGURATION. Once in a me

47、nu structure, place the cursor ( and keys) on the desired selection and press ENTER. Use the keypad to enter parameters. Use the EXIT key to back out of the menu structure and dis- able the menu. Table 1: MAIN MENU structure Menu itemDescription SAVESETUP SAVE RESTORE PWRON FACTORY DEFAULT USER SETU

48、P RESET Setup Menu: Save setup at a memory location (up to 10). Return 7001 to setup stored at a memory location. Power-on Menu: Power-on to factory default setup conditions. Power-on to setup stored at a memory location. Return 7001 to original power on setup. GPIB ADDRESS STATUS GPIB Setup Menu: Check/change IEEE-488 address. Display IEEE-488 status byte. DIGITAL-I/O OUTPUT-STAT