Allen ML5000+Service+Manual电路图.pdf

《Allen ML5000+Service+Manual电路图.pdf》由会员分享，可在线阅读，更多相关《Allen ML5000+Service+Manual电路图.pdf（135页珍藏版）》请在收音机爱好者资料库上搜索。

1、 ALLEN Mono Fader, Master Fader Centre, Master Fader L/R & Control Panel. 1) Cut the 2x Cable ties attaching the Stereo Slave PCB onto the Mono Fader & Control Panel PCBs. 2) Carefully remove the Stereo Slave PCB by pulling it upwards. 3) Once removed, turn the Stereo Slave PCB over. 4) To remove a

2、PCB, use a 5.5mm spanner to remove the relevant M3x4 Taptite Hex Headed Screws that attach the PCBs to the Master Fader bracket. 5) To remove a fader, remove the two relevant M3x5 Countersunk Pozi Screws with underhead pips (H) as shown in fig.4. Then unplug the fader wireform from the Stereo Slave

3、PCB, the fader can now be removed. De-solder the three fader wireform wires from the fader, taking note of the wire positions for refitting. 6) Removal of the H shaped Control Panel PCB can only be achieved once the vertical section of PCB has been removed. Once the vertical section has been removed

4、, remove the 2x M3x6mm Pan Pozi Black screws attaching the H shaped Control Panel PCB to the fader bracket. The H shaped Control Panel PCB can then be removed. 10) To remove the Mute Group PCB, use a 5.5mm spanner to remove the two screws attaching the PCB to the fader bracket. The VCA Master Slave

5、PCB must be removed before the Master Fader PCBs can be removed. 11) Cut the 2x Cable ties attaching the VCA Master Slave PCB onto the Master Fader PCBs. 12) Remove the 15way Flexi cable running between the VCA Master Slave PCB and the Mute Group PCB. 13) Carefully remove the VCA Master Slave PCB by

6、 pulling it upwards. 14) Once removed, turn the VCA Master Slave PCB over. 15) To remove a PCB, use a 5.5mm spanner to remove the relevant M3x4 Taptite Hex Headed Screws that attach the PCBs to the Master Fader Bracket. 16) To remove a fader, remove the two relevant M3x5 Countersunk Pozi Screws (H)

7、from the Master Fader front panel (see fig.4). Unplug the fader wireform from the Stereo Slave PCB, the fader can now be removed. De-solder the three Fader wireform wires from the fader, taking note of the wire positions for refitting. Note: A fader can be removed without removing the IDC wireforms

8、and Slave PCB. 17) To refit any of the PCB assemblies, follow the above procedure in reverse order. Make sure all harnesses are aligned and plugged on. Test for correct operation. ML5000 Service Manual 29 Base removal and Internal PCB assemblies Before beginning any service work, remove all power to

9、 the unit and disconnect any signal cables where necessary. Ensure adequate lighting and use the correct tools. Before you can access the internal PCB assemblies, invert the console and remove the screws securing the base in place. Carefully lift the base off. Note that the Earth Strip has been remo

10、ved for clarity. MONO INPUT CONNECTOR PCBs MONO INPUT PCBs AUX, GROUP & LRC PCBs MASTER DISTRIBUTION PCB STEREO PCBs MIDI POWER PCB SYS-LINK II OUT PCB MONO INPUT PCBS EARTH BUSS PCBS EARTH BUSS PCBS 30 ML5000 Service Manual Removing a Mono Input PCB assembly Before beginning any service work, remov

11、e all power to the unit and disconnect any signal cables where necessary. Ensure adequate lighting and use the correct tools. 1) Remove the screws attaching the relevant Earth Strip running the length of the Mono section (see fig.6, right hand section only shown) then lift away the Earth Strip. 2) C

12、arefully detach the 50way IDC wireform from the Mono Input PCBs and the SYS-LINK II Input PCB as far as the relevant Mono Input PCB. Note: There are two different 50way IDC wireforms on either side of the Master section. Remove the relevant IDC wireform according to the side on which the particular

13、Mono Input PCB lies. 3) Remove all the knob and switch caps from the required Mono Input PCB, then remove the pot nuts underneath using an 11mm nutdriver. 4) The required Mono Input PCB can now be removed from the console. 5) To refit a Mono Input PCB assembly, follow the above procedure in reverse

14、order. Make sure all harnesses are correctly aligned and plugged on. Test for correct operation. fig.6 SYS-LINK II PCB Earth Strip 50 way IDC wireform ML5000 Service Manual 31 Removing the Master Distribution PCB assembly To access the Group and Auxiliary PCB assemblies it may be necessary to remove

15、 the Master Distribution PCB. Before beginning any service work, remove all power to the unit and disconnect any signal cables where necessary. Ensure adequate lighting and use the correct tools. 1) Before removing the Master Distribution PCB assembly, the console base must first be removed. 2) Loca

16、te the Master Distribution PCB assembly positioned near the centre of the console (see fig.7). 3) Unplug all attaching IDC wireforms from the Master Distribution PCB assembly. 4) Desolder the Earth wire from the PCB then carefully remove the Master Distribution PCB by pulling it away from the consol

17、e. 5) To refit the Master Distribution PCB assembly, follow the above procedure in reverse order. Use an inspection mirror to check that each connector and IDC harness is correctly aligned and plugged on. Note: If a switch is fitted to the rear of the Master Distribution PCB rather than solder links

18、 then make sure that it is set correctly. Test for correct operation. fig.7 Master Distribution PCB Earth wire LCR Option links or switch 32 ML5000 Service Manual Servicing the Meterbridge Assembly Before beginning any service work, remove all power to the unit. Ensure adequate lighting and use the

19、correct tools. 1) Remove all the plastic snap-in rivets along the face of the meter panel with your fingernails or other non-abrasive tool. 2) With a person standing at either end of the console, each using a small, thin screwdriver, place the screwdriver through each of the endmost bottom rivet hol

20、es (see fig 8). Raise the meter panel up with the screwdrivers so that the bottom becomes free of the extrusion. 3) The complete meter panel assembly can now be removed from the meter pod extrusion by pulling it away from the extrusion, bottom first (see fig.9), allowing access to the Meter PCB asse

21、mblies. Remove the two attaching IDC harnesses. fig.8 fig.9 ML5000 Service Manual 33 Servicing the MPS14 Power Supply Cleaning and Replacing the fan filters. At regular intervals, it is recommended that the foam fan filters are cleaned or replaced to ensure efficient operation of the power unit. Fai

22、lure to do so may reduce the efficiency or even damage the power unit. To remove the fan filters, switch off and disconnect all power to the MPS14. Remove the rack ears and place to one side. Remove the cover fixing screws and cover and place to one side. The foam fan filters can now be removed by s

23、imply sliding out of the slots. Either clean or fit new filters depending on their condition. Replace the filters and reassemble the power unit. Check the fans are running unobstructed before completely re-installing. Replacing the mains fuse The AC mains fuse is located on the rear of the MPS14 uni

24、t next to the AC mains connector. In the event of a mains surge or under-rated fuse value, the mains input fuse will rupture. Switch off the power supply and remove the mains lead plug from the “MAINS INPUT” socket on the rear of the unit. Check the fuse and replace if necessary. TO AVOID THE RISK O

25、F FIRE REPLACE FUSE WITH THE CORRECT TYPE ONLY, AS INDICATED ON THE UNIT AC mains input voltage Fuse type 100V 230V 10% T 5A 250V 20mm In the event of repeated failure of the mains fuse, consult the local dealer from where the unit was purchased. 34 ML5000 Service Manual ORDERING A CONSOLE To order

26、a new console please specify the model number and AC mains voltage for the Power Supply. MODEL DESCRIPTION ORDER CODE ML5000-32 32 Mono + 4 Stereo Input Channels ML5000-32 ML5000-40 40 Mono + 4 Stereo Input Channels ML5000-40 ML5000-48 48 Mono + 4 Stereo Input Channels ML5000-48 MPS14 Power Supply f

27、or ML5000 MPS14/* * - Specify the voltage and mains plug requirement for your area. ORDERING AN ACCESSORY To order an option please specify the model number required. MODEL DESCRIPTION ORDER CODE SIDECAR EXPANDER OPTIONAL 24 MONO INPUT SIDECAR ML5000-24SC DC POWER LEAD 2.9 METRE DC POWER LEAD 002-58

28、3 DC COMBINER LEAD 0.75 METRE DC COMBINER LEAD 002-584 SYS-LINK CABLE 2.8 METRE 37 WAY AUDIO CABLE 002-617 LOGIC CABLE 2.9 METRE 9 WAY LOGIC CABLE AL4155 GOOSENECK LAMP 18” GOOSENECK LAMP AL4061 32 CHANNEL DUSTCOVER 32 CHANNEL VINYL DUSTCOVER AP4121 40 CHANNEL DUSTCOVER 40 CHANNEL VINYL DUSTCOVER AP

29、4122 48 CHANNEL DUSTCOVER 48 CHANNEL VINYL DUSTCOVER AP4123 SIDE-CAR DUSTCOVER SIDECAR VINYL DUSTCOVER AP4234 MANUALS AND SUPPORT DOCUMENTATION MODEL DESCRIPTION ORDER CODE ML5000 User Guide AP3736 ML5000 SIDECAR User Guide AP4124 MPS14 POWER SUPPLY User Guide AP3898 SERVICE TOOLS The tools required

30、 to service the ML5000 are standard to an electronics service workshop and are easily obtainable. The following items are necessary for disassembly and service access: TOOL USE ORDER CODE 4mm Hexagon (Allen) key M6 side trim AT0033 1-point Crosshead screwdriver M3, 4AB AT0004 2-point Crosshead screw

31、driver M4, 6AB, 8B AT0002 11mm AF Nutdriver Potentiometer and headphone nuts 12mm Nutdriver Jack nuts 1.27mm Hexagon (Allen) key PSU DC Leads AT4142 2.5MM hexagon (Allen) key M4 Sidetrim 5.5mm AF Spanner Fader PCB M3 Hex 5mm Nutspinner D-Type Screws ML5000 Service Manual 35 ORDERING AN ASSEMBLY The

32、following assemblies for the ML5000 are supplied fully tested. Please quote the description and order code for the part required. Printed circuit board (PCB) assemblies: DESCRIPTION ORDER CODE Mono Input PCB assembly 002-529 Stereo Input PCB assembly 002-564 Group 1, 3, 5, 7 PCB assembly 002-552 Gro

33、up PCB assembly 002-553 Group 2, 4, 6, 8 PCB assembly 002-554 Aux 10 PCB assembly 002-545 Aux 12 PCB assembly 002-546 Aux 14 PCB assembly 002-547 Aux 16 PCB assembly 002-548 Master Distribution PCB assembly 002-556 LCR Mix PCB assembly 002-544 Mono Fader PCB assembly 002-530 Master Fader Centre PCB

34、assembly 002-589 Master Fader L/R PCB assembly 002-588 Master Fader VCA PCB assembly 002-557 Mute Group PCB assembly 002-563 Control Panel PCB assembly 002-549 Fader Slave PCB assembly 002-551 Stereo Slave PCB assembly 002-566 VCA Master Slave PCB assembly 002-567 Aux Master Slave PCB assembly 002-5

35、43 CPU PCB assembly 002-550 Mono Connector PCB assembly 002-560 Stereo LRC Connector PCB assembly 002-565 Master Connector PCB assembly 002-555 MIDI Power PCB assembly 002-575 Sidecar MIDI Power PCB assembly 002-598 SYS-LINK 2 In PCB assembly 002-587 SYS-LINK 2 Out PCB assembly 002-596 Meter 1-8 PCB

36、 assembly 002-558 Meter 9-16 PCB assembly 002-591 Meter Master PCB assembly 002-559 Meter Ledbar PCB assembly 002-590 36 ML5000 Service Manual IDC connector harnesses: DESCRIPTION ORDER CODE 10 way GRAUX harness AL4029 10 way Input harness AL4028 10 way LRC to Fader harness AL4077 10 way MIDI harnes

37、s AL4032 16 way GRAUX harness AL4030 20 way Master Connector harness AL4027 20 way Meter harness AL4021 26 way CPU Power harness AL4033 26 way LRC Connector harness AL4031 26 way Distribution harness AL4020 26 way Slave A harness AL4022 26 way Slave B harness AL4023 26 way Slave C harness AL4024 26

38、way Slave D harness AL4025 34 way Master harness AL4026 Sidecar harness AL4067 ML5-32 Left harness AL3964 ML5-32/40 Right harness AL3967 ML5-40/48 Left harness AL3834 ML5-48 Right harness AL3835 THE CHASSIS TRIM DESCRIPTION ORDER CODE ML5000 (all formats) Left & Right Chassis side trims AA3773-L/R L

39、eft & Right Moulded side trims AA3781-L/R Write-on strip 10 AK0327 Ident strip Master Rear AK3788 Ident strip Master AK3833 Ident strip 1-24 AK3789 Ident strip 1-24 Rear AK3790 Ident strip 25-48 AK3795 Ident strip 25-48 Rear AK3796 ML5000 Service Manual 37 ORDERING AN ML5000 SPARES KIT It is recomme

40、nded that the spares kit order code 002-533 is held and maintained by the service agent to enable in-field service repairs to the ML5000 independent of the ALLEN & HEATH factory. Commonly available items such as resistors, capacitors, tools and soldering equipment are not included. The contents of t

41、he kit are listed below and are supplied in a cabinet of drawers. Individual spare parts may be ordered. Please quote the description and order code for the part required. Fixings: DESCRIPTION ORDER CODE QTY Screw 4AB x 5/16” CSK Pozi Black AB0059 20 Screw M3 x 8 CSK Pozi Black AB0074 10 Nylock Nut

42、M3 AB0102 10 Nylock Nut M4 AB0105 10 Screw 4AB x 1/2 Pan Pozi Black AB0250 10 Screw M6 x 20 CSK Allen Black AB0310 5 Screw 6B x 3/8 CSK Pozi Zinc AB2082 20 Screw 8B x 3/8 CSK Pozi Black AB2085 5 Screw 6B x 5/16 Pan Pozi Black AB2809 20 Screw 4 x 5/16 Poly Pan Pozi Black AB2810 20 Screw M3 x 5 CSK Po

43、zi Black AB2811 20 Screw M3 x 4 TT Hex Head Black AB3837 20 Screw M6 x 10 CSK Pozi Zinc AB4036 5 Screw 6B x 3/8 Flange Headed Pozi Black AB4037 10 Rivet Plastic Snap SR3535B AB4092 5 Pot Nut 9mm AB8050 50 Knobs and caps: DESCRIPTION ORDER CODE QTY Knob Red & Grey 11mm D AJ2074 10 Knob Blue & Grey 11

44、mm D AJ2075 40 Knob Light Blue & Grey 11mm D AJ2076 40 Knob Green & Grey 11mm D AJ2077 15 Knob Dark Grey & Grey 11mm D AJ2078 15 Knob Yellow & Grey 11mm D AJ2079 10 Knob Brown & Grey 11mm D AJ2080 10 Button 10 x5mm Rectangular Grey AJ2865 2 Button 10 x5mm Rectangular Black AJ3228 1 Fader Knob 11mm B

45、lack + White Line AJ3503 15 Switch Cap Grey 6x6mm Offset AJ3863 20 Button Illuminated Red AJ3949 2 Switch Cap White Offset AJ3950 20 38 ML5000 Service Manual Button 6x6mm Square White AJ3951 10 Button 6x6mm Square Light Grey AJ3952 5 Button 6x6mm Square Red AJ3953 10 Button 6x6mm Square Black AJ3954

46、 5 Button 8mm Round Light Grey AJ3955 10 Fader Knob 11mm White+Black Line AJ8078 10 Fader Knob 11mm Red+Black Line AJ8079 10 Fader Knob 11mm Yellow+Black Line AJ8080 5 Fader Knob 11mm Blue+Black Line AJ8081 10 Button Illuminated White AJ8107 10 Faders, Potentiometers, Switches and connectors: Pot 10

47、KC x 2 (103C 14mm wide) AI0150 3 Pot 20KK (203K 11mm wide) AI8003 5 Pot 20KB C/D (203B 11mm wide) AI8004 5 Pot 200KC x 2 (204C 11mm wide) AI8005 5 Pot 20KB x 2 centre click (14mm wide) AI8006 5 Pot 20KK x 2 (203K 14mm wide) AI8007 10 Pot 10KAC x2 (103AC 14mm wide) AI8008 10 Pot 200KC x 2 (204C 14mm

48、wide) AI8009 5 Fader 10KSPE 100mm AI8109 3 Pot 5K (502RD 11mm wide) AI8111 5 Fader 10KB 100mm AI8175 10 Fader 10KA 60mm AI8176 5 Switch 2PCO Latching 90 Deg AL0162 10 Jack Socket Headphone AL0328 1 Switch 4PCO Latching AL0333 15 Switch 2PCO Momentary AL0374 10 XLR 3 Pin Female Vertical PCB Mount AL2410 5 XLR 3 Pin Male Vertical PCB Mount AL2411 5 Switch Slide MINI SPDT PCB AL3081 1 Jack Socket ” Stereo Unswitched AL3407 20 Jack Socket ” Stereo Switched AL3410 20 LEDs and Semiconductors: Transistor BC549 NPN