digitech_S200_manual电路图.pdf

《digitech_S200_manual电路图.pdf》由会员分享，可在线阅读，更多相关《digitech_S200_manual电路图.pdf（23页珍藏版）》请在收音机爱好者资料库上搜索。

1、Dual-Engine Multi-Effects Processor Please visit Digitech Studio on the World Wide Web at Users Guide RadioFans.CN 收音机爱 好者资料库 WARNING FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING: WATER AND MOISTURE: Appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub,

2、 in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. POWER SOURCES:The appliance should be connected to a power supply only of the type described in the operating instructions or as marked

3、 on the appliance. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against the

4、m, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. SERVICING:To reduce the risk of fire or electric shock, the user should not attempt to service the appliance beyond that described in the operating instructions. All other ser

5、vicing should be referred to qualified service personnel. FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE:Replace fuse with same type and rating only. SAFETY INSTRUCTIONS NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD. WARNING: THIS APPLIANCE MUST BE EARTHED. The cores

6、 in the mains lead are coloured in accordance with the following code: GREEN and YELLOW - Earth BLUE - Neutral BROWN - Live As colours of the cores in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The core w

7、hich is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow. The core which is coloured blue must be connected to the terminal marked N or coloured black. The core which is coloured brown m

8、ust be connected to the terminal marked L or coloured red. This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. If the attachment plug needs to be changed, refer servicing to qualified service personnel who sh

9、ould refer to the table below. The green/yellow wire shall be connected directly to the units chassis. WARNING: If the ground is defeated, certain fault conditions in the unit or in the system to which it is connected can result in full line voltage between chassis and earth ground. Severe injury or

10、 death can then result if the chassis and earth ground are touched simultaneously. Line Neutral Earth Grnd. CONDUCTOR L N Brown Blue Green/Yel. Black WIRE COLOR White Green U.K. MAINS PLUG WARNING A moulded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitabl

11、e disposal facility. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and MUST be ASTA app

12、roved to BS1362. The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products.The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit.The exclamation point in an equilateral

13、 triangle indicates that it is necessary for the user to refer to the owners manual. These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any

14、 reason will void the manufacturers warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage. CAUTION ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR WARNING: TO REDUCE T

15、HE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE RISK OF ELECTRIC SHOCK DO NOT OPEN ELECTROMAGNETIC COMPATIBILITY This unit conforms to the Product Specifications noted on the Declaration of Conformity. Operation is subject to the following two conditions: this devi

16、ce may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Operation of this unit within significant elec- tromagnetic fields should be avoided. use only shielded interconnecting cables. RadioFans.CN 收音机爱 好

17、者资料库 DECLARATION OF CONFORMITY Manufacturers Name:Digitech Studio Manufacturers Address:8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product Name:S-200 Product Options:All conforms to the following Product Specifications: Safety:EN 60065 (1993) IEC 65 (1985) with Amendment

18、s 1, 2 & 3 EMC:EN 55013 (1990) EN55020 (1991) Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. Digitech Studio President of Digitech Studio 8760 S. Sandy Parkway Sandy

19、, Utah 84070, USA Tel: 801.566.8800 Fax: 801.566.7005 Effective May 1, 1998 European Contact: Your Local Digitech Studio Sales and Service Office or International Sales Office 3 Overlook Drive #4 Amherst, New Hampshire 03031, USA Tel: 603.672.4244 Fax: 603.672.4246 S-200 User Guide I RadioFans.CN 收音

20、机爱 好者资料库 Table of Contents Safety Information Declaration of Conformity.I Table of Contents .II Section 1 - Introduction Congratulations.1 Included Items .1 S-200 Features.1 Warranty .2 A Quick Tour of the S-200.3 The Front Panel.3 The Rear Panel.4 Section 2 - Operation and Editing Program Mode .5 N

21、aming Program Storing Changes .5 Selecting Effect Configurations .6 Editing Engine A and B Engines.6 Selecting and Editing Effects .6 EQ and Noise Gate Adjustments.7 Adjusting the Dry Path Defeat .8 Adjusting the Display Contrast .9 MIDI Functions .9 MIDI Channel Selection .9 MIDI CC Command Informa

22、tion .10 Section 3 - Effects and Parameters Modulation Effects .11 Pitch Shifters .12 Delay .12 Reverb .13 Other Effects (Vocoder, Ring Modulator, Compressor and De-Esser) .14 Section 4 - Appendix Resetting the S-200 .15 Footswitch Set-Up .16 Specifications.17 Program List .18 S-200 User Guide II Se

23、ction-1 Introduction Congratulations. . you are now the owner of a Digitech Studio S-200 multi-effects processor. The S-200 offers you Dual-Engine processing with Stereo input and output routings. The S-200 offers a full palette of Studio digital effects that can accommodate any studio or live situa

24、tion, making the S-200 a true power plant effects processor. This Users Guide is your key to understanding the powerful world of the S-200. Read it carefully. After youve had time to familiarize yourself with the unit, feel free to utilize the S-200 to its full processing potential. Good luck, and t

25、hank you for choosing Digitech Studio. Your S-200 was carefully assembled and packaged at the factory. Before you proceed any further, make sure the following items are included: (1) S-200 Users Guide (1) Digitech Studio S-200 Dual Engine Multi-Effects processor (1)Power Cord (1)Digitech Studio warr

26、anty card Please save all packing materials. They were designed to protect the unit from damage during shipping. In the unlikely event that the unit requires service, use only the factory supplied carton to return the unit. S-200 User Guide Section -1 Introduction 1 S-200 Features: Stereo Inputs and

27、 Outputs Dual-Engine Processing Large Custom Display 24-bit signal path, 48-bit internal data path 96 dB signal to noise ratio Vocoder Effect Module 5 Effect Routing Configurations Studio Reverbs and Modulation Effects 20 bit A/D and D/A Converters MIDI Program Change and CC Commands Footswitch Cont

28、rol Compressor and De-Esser Effects Warranty We at Digitech Studioare very proud of our products and back-up each one we sell with the following warranty: 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. Digitech Studio warrants this

29、product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3. Digitech Studio liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to Di

30、gitech Studio WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. A Return Authorization number may be obtained from Digitech Studio by telephone. The company shall not be liable for any consequential damage as a result of the products use in any circuit

31、or assembly. 4. Proof-of-purchase is considered to be the burden of the consumer. 5. Digitech Studio reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6. The

32、consumer forfeits the benefits of this warranty if the products main assembly is opened and tampered with by anyone other than a certified Digitech Studio technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. 7. The foregoing is in lieu of all oth

33、er warranties, expressed or implied, and Digitech Studio neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall Digitech Studio or its dealers be liable for special or consequential damages or from any delay in t

34、he performance of this warranty due to causes beyond their control. DigiTech Studio and S-200 are registered trademarks of the Harman Music Group Incorporated. NOTE: The information contained in this manual is subject to change at any time without notification. Some information contained in this man

35、ual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The information contained in this version of the owners manual supersedes all previous versions. Section -1 Introduction S-200 User Guide 2 A Quick Tour of the S-

36、200 The Front Panel 1) Display - This large custom display is where you receive information for programming and operation of the S-200. This information includes: effect types and parameters and all Utility mode functions including Contrast, Dry level, MIDI program information, Factory Reset and Foo

37、tswitch set-up. 2) Program Descriptions - This list tells you the factory program list of all Factory 99 programs in the S-200. 3) Program/Data Wheel - In Program mode, this wheel is used to change programs and when the unit is in Edit mode it is used to select effects and change parameters. 4) Prog

38、ram Button -This button returns the S-200 to program mode when pressed. 5) Configuration Button - This button is used to select Configuration mode. Once pressed, use the wheel to select a different effect configuration for the selected program. 6 a-d) Effect Parameter Editing Buttons - These four bu

39、ttons allow you to do all parameter editing of effects in Edit and Utility modes in conjunction with the wheel. 7) Engine A/B Select - This button selects the Engine A and B effect engine modules. Successive presses of this button will toggle between Engines A/B in effect configurations 2-5. Once th

40、is button is pressed and the Engine effect module has been selected, use the wheel to select the effect to be used in this effect engine module. 8) EQ/Gate - This button (in conjunction with the four parameter buttons) are used to adjust the three band EQ and Noise gate threshold and release. Press

41、once to select the EQ and press twice to select the Noise Gate. 9) Utility - This button is used to access all Utility mode functions including: Dry signal path On and Off, selecting the MIDI channel, adjusting the display contrast and footswitch set-up. 10) Preview - This button produces a brief re

42、ference tone to audition effect sounds without the use of an input signal. 11) Store Button - This button is used to store program modifications in the S-200. 12) Bypass - This button is used to Bypass all of the digital effects in the S-200 and allow the original dry signal to pass through the S-20

43、0. 123 456 a-d78910 11 12 FACT USER UTIL EDIT CHNG LINK MIDI Stereo Large Hall Hall L R L R ngeq S-200 User Guide Section -1 Introduction 3 The Rear Panel 1) Input Level- This knob controls the level of signal entering the S-200. For optimal performance, set this level so the Input level indicators (located on the front panel) occasionally peak the bargraph. 2) Left/Mono Input - Thi