Allen SR+Plus+owner+manual+AP0076+part+2电路图.pdf

《Allen SR+Plus+owner+manual+AP0076+part+2电路图.pdf》由会员分享，可在线阅读，更多相关《Allen SR+Plus+owner+manual+AP0076+part+2电路图.pdf（9页珍藏版）》请在收音机爱好者资料库上搜索。

1、S R S E R I E S OW.:NER H A N D B O O K 2 Effective,from serial number 501001 onwards. This manual includes operating and service information for all models of the SR Series currently in production. Where differences between models exist, such as four bus and two bus models, this is indicated in the

2、 text. CONTENTS PAGE INTRODUCTION . Specification Service screen to case. Connect unbalanced signals to the tip and link ring and case to the screen of the cable. RadioFans.CN 收音机爱 好者资料库 S R S E R I E S O W N E R H A N D B O O K 2 3 Connexion - of Stereo Recorder Mixer main outputs LEFT and RIGHT ar

3、e the stereo output for the mastering recorder. The output level is adjustable for any tape machine input level and balanced output available. Refer to OPTIONS section of this handbook for more information. The outputs are supplied unbalanced. Connect signal to pin 3 on the XLR type connectors and s

4、creen to pin 1. Stereo machine outputs should be connected to any adjacent pair of available line inputs. Generally, these are the last two on the mixer (channels 15, 16 - 23, 24). See CONNEXION DETAILS. Connexion - of Monitor Output The operators monitor output is available o n a 1/4 jack socket an

5、d is labelled MON OUT. This is an unbalanced stereo circuit designed for use with stereo power ampl if iers with an input sensitivity rating of lOOmV to 1V (approximately) for full rated output. Connect the TIP of the monitor output jack to the LEFT amplifier channel, and the RING to the RIGHT chann

6、el, SCREEN to case. Mixer outputs generate turn-on thumps, which can strain loudspeakers if the mixer is turned on while the power amp is on. To avoid this, it is good practice to always have ALL other equipment in your system turned on BEFORE turning on any power amps. Connexion - of Fx Devices As

7、supplied, AUX A and AUX B would generally be used as FX sends as they are factory wired to take their signal AFTER the channel fader. Wired like this, if a channel which is being sent to the FX device is turned down in the mix, the level of signal send from that channel is also turned down proportio

8、nally. This prevents that channel from leaking into the mix via the FX device when it is not wanted there. As with other mono unbalanced outputs, connect TIP tokthe device input, SCREEN to earth. Use of Aux C as Additional Fx Send - - As mentioned above, it is generally undesirable to take FX sends

9、from any but post fader sources for the reasons described. Provision has been made within the mixer to allow the user to select the source from which an aux send control derives its source. As supplied, AUX C is a PRE-EQ send from the input channels, but no send from the tape return section is provi

10、ded. It is therefore suggested that the POST FADER source option be selected for AUX C, making it an additional FX send which can be returned to any available INPUT channel. Connexion - of Cue (Foldback) Amp1 if iers In recording applications, AUX D is intended for use as the CUE, or foldback mix. P

11、rovision has been made within the GROUP section which allows tape tracks to be mixed to this bus for the purpose of monitoring them during overdubs. This is a MONO, UNBALANCED output, and can be fed to a mono amplifier, stereo ampl if ier, (using a suitable adaptor cable) or a stereo amp strapped fo

12、r mono operation as shown in CONNEXION DIAGRAM. See amp manufacturers instructions for mono operation. For distribution of CUE program to several pairs of headphones, the power amplifier output should be divided by a suitable resistor. RadioFans.CN 收音机爱 好者资料库 S R S E R I E S O W N E R H A N D B O O

13、K Connexion of Mono Output - The mono out is an XLR connector with signal to pin 3 and screen to pin 1. Balanced output is an option, refer to options section. If desired, the mono output can be used to drive a power amplifier connected to a loudspeaker in the studio for the purpose of track playbac

14、k. While not practical for the purpose of overdubbing, it can be quite handy if you have a large number of people in the studio as it can keep them from running in after a track is completed and crowding the control room where you are trying so hard to keep a semblance of order. S R S E R I E S O W

15、N E R H A N D B O O K SR RANGE: CONNEXION DETAIL MULTITRACK RECORDIN0 connexion viewed from rear of mixer PHONES n MONITOR OUT 4 a 0 b v w A U X W T MONO OUT R OUT FX UNIT 1 IN OVI A 1 A 0 INOCRT 1 r FX FILTl 416.424 ONLY r INEERT a AT ANY INBERT lQROUP OUT a LINE IN LINE IN DRUM MONITOR oa SlOE FIL

16、L SR RANGE: CONNEXION DETAIL l29 MONOITOR 0 OUT , AUX A OUT hA 0 LOUO=PIAK. SOUND REINFORCEMENT APPLICATIONS FX UNIT P FX UNT i (cLOOI MONITORS . a POWRR AMP CCRODDOVER IN II- AMPtO M I E M . 3 VIEW F R O M REAR O F MIXER I % - = I OROUP OUT I LINE IN C - - - - - - , , - I ALL HlQW LEVEL 0DUC)CEB I

17、ittitittit OOm - LIMITER OIAPWIC S R S E R I E S O W N E R H A N D B O O K 28 IMPORTANT - PLEASE READ AND UNDERSTAND! EARTH I NG Mains electricity is dangerous and can kill. Most pieces of mains powered equipment have an earth wire running from the case to the mains plug. (Some are double insulated

18、and do not need this.) This earth wire is there for safety. Unfortunately with many earthed items wired together sound quality can suffer. It is common practice in studios to disconnect some of these earth wires for sound quality reasons. This can be dangerous. Equipment will still work even if it i

19、s not earthed. This does not mean it is safe! Government and insurance underwriters electrical codes must be observed. These codes take precedence over any suggestions contained in this manual. The sound quality problems mentioned are hum and interference, caused because there are several paths to e

20、arth (along the audio screens and down a1 1 the mains earths). The problem can be overcome by having just one piece of equipment connected to mains earth (usually the power amp). Do not leave the earth wire loose in a mains plug as it may touch the live termina 1. Having only one item connected to m

21、ains earth means that all the others rely on the audio screen or ground for safety. It is important to remember this. Test regularly that all exposed metal gear including microphones, guitar strings and D I boxes have a low resistance to mains earth. This A1 len & Heath mixer case is not connected t

22、o mains earth, for the audio reasons mentioned. The mixer power supply is however, and this earth must not be removed. It is best to plan ahead and have your installation checked by a competent engineer before you commence. Do not trust equipment and installations modified . by others before you. S

23、R S E R I E S O W N E R H A N D B O O K 2 9 SUPPLY VOLTAGES Supply type MPS8P, MPS9 or RPSl provides the DC supply for all mixer .functions. It is factory set for operation on the required AC supply as follows: Europe 220/240v AC 50Hz North America 110/120v AC 60Hz Japan 1 OOv 50/60Hz. The supply vo

24、ltage setting may be altered to suit local requirements if required. HEALTH AND SAFETY NOTICE - The DC power unit is intended for connection with high voltage supply as stated above. Interference with the internal assembly while connected to the supply presents a risk of lethal electric shock. When

25、service work is called for first, DISCONNECT THE EQUIPMENT FROM THE AC SUPPLY. DO NOT RECONNECT UNTIL THE WORK I S COHPLETE AND COVER I N PLACE. Refer to the circuit diagram MPS8P, MPS9 or RPSl for reconnection details. This work should be carried out by qualified service personnel to avoid risk of damage to the equipment and operators.