Allen_&_Heath_ML3000_Service_Manual电路图.pdf

《Allen_&_Heath_ML3000_Service_Manual电路图.pdf》由会员分享，可在线阅读，更多相关《Allen_&_Heath_ML3000_Service_Manual电路图.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。

1、 SERVICE MANUAL SERVICE MANUAL Publication AP4511 Dual Function Live Sound Console RadioFans.CN 收音机爱 好者资料库 2 ML3000 Service Manual Introduction This service manual provides technical information on the Allen & Heath ML3000 audio console. Included is the technical specification, system block diagram,

2、 circuit schematics with board layouts, and a spare parts list. Information on the power supply is available in a separate publication. Only technically qualified service personnel should carry out service work on the console and its power supply. Whilst we believe the information in this manual to

3、be reliable we do not assume responsibility for inaccuracies. We also reserve the right to make changes in the interest of further product development. We are able to offer further product support through our world-wide network of approved dealers and service agents. You can also access our Web site

4、 on the Internet for information on our product range and further technical support. To help us provide the most efficient service please keep a record of the console serial number, and date and place of purchase to be quoted in any communication regarding this product. The serial number is located

5、on the rear panel. Check out our home site for information on the company and its pedigree, our full product range and our design philosophy. We also have a site dedicated to the ML Series consoles. www.allen- ML3000 Service Manual AP4511 Issue 1 Copyright 2002 Allen & Heath. All rights reserved Thi

6、s product complies with the European Electromagnetic Compatibility directives 89/336/EEC & 92/31/EEC and the European Low Voltage Directives 73/23/EEC & 93/68/EEC. This product has been tested to EN55103 Parts 1 & 2 1996 for use in Environments E1, E2, E3, and E4 to demonstrate compliance with the p

7、rotection requirements in the European EMC directive 89/336/EEC. During some tests the specified performance figures of the product were affected. This is considered permissible and the product has been passed as acceptable for its intended use. Allen & Heath has a strict policy of ensuring all prod

8、ucts are tested to the latest safety and EMC standards. Customers requiring more information about EMC and safety issues can contact Allen & Heath. NOTE: Any changes or modifications to the console not approved by Allen & Heath could void the compliance of the console and therefore the users authori

9、ty to operate it. Manufactured in the United Kingdom by Allen & Heath Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK http:/www.allen- RadioFans.CN 收音机爱 好者资料库 ML3000 Service Manual 3 Contents Important Safety Instructions .4 Mains Plug Wiring Instructions.5 General Precautions .5 ML3000 Ke

10、y Features.6 Front Panel Layout.7 Rear Panel Layouts.8 Technical Specifications.9 System Block Diagram. 10-11 Installation Details.12 Earthing.13 Audio Connector Types and Wiring.14 Gain Structure.15 MIDI. 16-18 Console Computer and Operating Software.19 Internal Option Links.20 Internal assembly as

11、signments.20 The Range .21 Ordering an Assembly. 22-23 Ordering a Spares Kit. 24-27 SYS-LINK fitting instructions.(1-4) TECHNICAL DRAWINGS. BLOCK DIAGRAM.M1 MONO INPUT. D1-D3 STEREO INPUT . D4-D7 MASTER CONNECTOR. D8-D10 GROUP / AUX . D11-D13 AUX MATRIX. D14-D16 MASTER DISTRIBUTION . D17-D18 SYSLINK

12、 INPUT. D19-D20 MIDI POWER. D21-D22 CPU . D23-D26 LCR SLAVE. D27-D29 MASTER FADER. D30-D33 MASTER. D34-D37 MONO FADER. D38-D40 MONO CONNECTOR. D41-D42 SYSLINK OUTPUT. D43-D44 METER MASTER . D45-D47 METER 1-8 & 9-16 V2. D48-D50 METER LEDBAR. D51 RadioFans.CN 收音机爱 好者资料库 4 ML3000 Service Manual Importa

13、nt Safety Instructions WARNINGS - Read the following before proceeding : ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Read instructions: Retain these safety and operating instructions for future reference. Adhere to all warnings printed here and on the console power unit. Follow the operating

14、instructions printed in this user guide and the power unit user guide. Do not remove covers: Operate the power unit with its covers correctly fitted. Refer any service work to competent technical personnel only. Power sources: Connect the power unit to a mains power only of the type described in thi

15、s User Guide and marked on the rear panel. Use the power cord with sealed mains plug appropriate for your local mains supply as provided with the console. If the provided plug does not fit into your outlet consult your service agent for assistance. Power cord routing: Route the power cord so that it

16、 is not likely to be walked on, stretched or pinched by items placed upon or against it. Grounding: Do not defeat the grounding and polarisation means of the power cord plug. Do not remove or tamper with the ground connection in the power cord. Water and moisture: To reduce the risk of fire or elect

17、ric shock do not expose the power unit or console to rain or moisture or use it in damp or wet conditions. Do not place containers of liquids on it which might spill into any openings. Ventilation: Do not obstruct the ventilation slots or position the console or power unit where the air flow require

18、d for ventilation is impeded. If the console is to be operated in a flightcase ensure that it is constructed to allow adequate ventilation. Heat and vibration: Do not locate the power unit in a place subject to excessive heat or direct sunlight as this could be a fire hazard. Locate the console and

19、its power unit away from any equipment which produces heat or causes excessive vibration. Servicing: Switch off the equipment and unplug the power cord immediately if it is exposed to moisture, spilled liquid, objects fallen into the openings, the power cord or plug become damaged, during lightening

20、 storms, or if smoke, odour or noise is noticed. Refer servicing to qualified technical personnel only. Installation: Install the console in accordance with the instructions printed in this User Guide. Do not connect the output of power amplifiers directly to the console. Use audio connectors and pl

21、ugs only for their intended purpose. CAUTION WARNING: This equipment must be earthed. ML3000 Service Manual 5 Important Mains Plug Wiring Instructions. The power unit is supplied with a moulded mains plug fitted to the AC mains power lead. Follow the instructions below if the mains plug has to be re

22、placed. The mains lead wires are coloured in accordance with the following code: WIRE COLOUR TERMINAL European USA/Canada L LIVE BROWN BLACK N NEUTRAL BLUE WHITE E EARTH GND GREEN & YELLOW GREEN The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked

23、 with the letter E or with the Earth symbol. This appliance must be earthed. The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N. The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter

24、 L. Ensure that these colour codes are followed carefully in the event of the plug being changed. General Precautions Damage : To prevent damage to the controls and cosmetics avoid placing heavy objects on the control surface, scratching the surface with sharp objects, or subjecting the console to r

25、ough handling and vibration. Environment : Protect from excessive dirt, dust, heat and vibration when operating and storing. Avoid tobacco ash, smoke, drinks spillage, and exposure to rain and moisture. If the console becomes wet, switch off and remove mains power immediately. Allow to dry out thoro

26、ughly before using again. Radiation : To avoid induced noise and interference pickup do not operate the console close to strong sources of electromagnetic radiation such as power supplies, video monitors, lighting cables and dimmers. Cleaning : Avoid the use of chemicals, abrasives or solvents. The

27、control panel is best cleaned with a soft brush and dry lint-free cloth. Stubborn marks can be removed using a cloth dampened with isopropyl alcohol. Do not leave marking tape stuck to the console for long periods of time as the adhesive can degrade and leave a sticky residue. The faders, switches a

28、nd potentiometers are lubricated for life. The use of electrical lubricants on these parts is not recommended. Refer to the power unit user guide for instructions on cleaning its ventilation filters. Transporting : The console should be transported in the original packing or purpose built foam lined

29、 flightcase. Protect the control surface from damage during transit. The console is a large and heavy item. To avoid injury ensure adequate man power and precaution when lifting or moving the console. 6 ML3000 Service Manual ML3000 Key Features The Allen & Heath ML3000 is a small footprint, affordab

30、le VCA equipped dual function live sound console providing many of the features of its larger brothers the ML4000 and ML5000. It can be quickly configured for front-of-house (FOH) or stage monitor mixing. As one console suitable for both applications it is equally well suited to installation, rental

31、 and touring. It offers an IO capability and feature set that satisfies the latest requirements of live sound engineering, in particular the growing number of inputs and outputs for multi-speaker house and monitor systems, demands of stereo in-ear monitoring, 3 speaker LCR imaging, advanced grouping

32、 and automation. The design ensures on-the-road durability, a clear layout for easy walk up and go operation, and no- compromise audio performance. Inputs and Outputs 3 Standard frame sizes: 24+2, 32+2, 40+2 (mono + dual stereo channels) 24, 32, 40 mono mic/line inputs with inserts and direct output

33、s 2 dual stereo line inputs Sys-Link option to link consoles for more channels Main Left, Right and Centre outputs with inserts, Centre configurable as the engineers monitor 4 Groups, 8 Auxes: Group/Aux 1-4 and Aux 5-8 with faders and inserts, Aux 1-4 with rotaries Aux 7/8 configurable as mono or st

34、ereo with level and pan controls 8x4 Matrix 2-Track monitor input and recording send Stereo headphones and local monitors Talkback mic input Talkback/Oscillator output Groups and Automation 8 VCA groups with mutes 4 audio groups with LCRplus sub grouping 8 mute groups MIDI accessible snapshot memori

35、es MIDI mute on/off, snapshot recall and dump in/out control Processing and Control 4-Band 2 sweep mono EQ, 4-band fixed frequency stereo EQ Sweepable high pass filter LCRplus 3 speaker imaging system Protected mode switching to configure the console for FOH or monitor application PFL override AFL o

36、verride selected monitor source Assignable talkback 1kHz tone and pink noise generator for system line-up and testing Full console monitoring and extensive metering with LED bars and illuminated VU ML3000 Service Manual 7 Front Panel Layout PK SIG +6 0 ASSIGNED GROUP O O 30 5 0 10 5 40 10 20 O O 30

37、5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 30 5 0 10 5 40 10 20 O O 5 0 10 5 O O 30 5 0 10 5 40 10 20 30 40 10 20 O O 5 0 10 5 30 40 10 20 PK SIG +6 0 ASSIGNED GROUP O O 3

38、0 5 0 10 5 40 10 20 PK SIG +6 0 ASSIGNED GROUP LR = BAL + BLEND LCR= CLR MIX MAIN 3 O O+6 AUX 4 O O+6 AUX 5 O O+6 AUX 6 O O+6 AUX AUX +6OO 2 AUX +6OO 1 EQ IN PRE 1-2 3-4 +6OO +6OO PRE PRE STEREO LR = BAL + BLEND LCR= CLR MIX MAIN 3 O O+6 AUX 4 O O+6 AUX 5 O O+6 AUX 6 O O+6 AUX AUX +6OO 2 AUX +6OO 1

39、EQ IN PRE 1-2 3-4 +6OO +6OO PRE PRE STEREO 3 10 18 -3 GAIN -6 3 10 18 -3 GAIN -6 3 10 18 -3 GAIN -6 3 ON ST1 10 18 -3 GAIN -6 ON ST2 ON ST3 ON ST4 AUX LEV PAN 7 AUX 8 7-8 AUX LEV PAN 7 AUX 8 7-8 PFL MUTE GROUP ASSIGN PFL MUTE GROUP ASSIGN O O+6 AFLAFL O O+6 GRP/AUX LR = PAN LRC = LCR BLEND + MAIN MI

40、XMIX MAIN + BLEND LCR= CLR PAN = RL AFL reversereverse MONITOR FOH mode AFL O O+6 AFLAFL O O+6 LR = PAN LRC = LCR BLEND + MAIN MIXMIX MAIN + BLEND LCR= CLR PAN = RL AFL reversereverse AFL MUTEMUTEMUTEMUTE AFLAFLAFLAFL MUTEMUTEMUTE TBTBTBTBTBTBTBTB MUTE GRP/AUXGRP/AUXGRP/AUX O O+6 +6OO AFL O O+6 O O+

41、6 O O+6 O O+6 O O+6 O O+6 C 4 R L 3 2 1 O O+6 LEV +6OO AFL O O+6 O O+6 O O+6 O O+6 O O+6 O O+6 C 4 R L 3 2 1 O O+6 LEV +6OO AFL O O+6 O O+6 O O+6 O O+6 O O+6 O O+6 C 4 R L 3 2 1 O O+6 LEV +6OO AFL O O+6 O O+6 O O+6 O O+6 O O+6 O O+6 C 4 R L 3 2 1 ONONONON PHONES 100 TALK TO TB TB TO LR TB TO C maxmi

42、n +48V TRIM TALKBACK MIC IN maxmin TRIM PINK NOISE 1kHz OSC OSC/NOISE TO TB Disable OSC/NOISE MTX 1-4 AUX 5-8 METERS POWER MONO LR 2TRK C LCR LOCAL MONITOR 100 SLAVE mode RS232 MIDI Press and Hold with GRP MUTE View on channels MIDI LISTEN WEDGE C MAIN MIX DUMP WEDGE mode CH1-16 LEV 0 OO 30 10 20 5

43、5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 0 OO 30 10 20 5 5 10 LEVLEVLEVLEV SOURCE Assign MUTE and VCA groups: Select using GRP MUTE Assign using CH MUTES M U T E ASSIGN VIEW M A S T E R M A S T E R M U T E M A

44、S T E R M U T E M A S T E R M U T E M A S T E R M U T E M A S T E R M U T E M A S T E R M U T E M A S T E R M U T E PFL 3-4 GROUP ASSIGN L MUTE R PAN LR = LCR BLEND =+ O O 1-2 C MAIN MIX +6 EQ IN +6 LEV AUX PAN 8 O O AUX 7-8 7 OO STEREO +6 PRE +6 AUX 6 OO AUX 5 OO +6 PRE AUX 4 OO AUX 3 O O +6 +6 AUX 2 O O AUX 1 +6 PRE 500Hz15k LM -15 -15 +15 +15 LF 180 -15 35Hz 45 80 +15 400 1k 250 HM 400HzOFF 2.5k 1k 700 -15+15 4k 6k HF 50 10- 10 20 GAIN 020 O 60 40 HPF 200 100 20dB PAD 40 +48V 8 ML