Alto_AMX-140FX-USB_Mixer_Service_Manual电路图.pdf
《Alto_AMX-140FX-USB_Mixer_Service_Manual电路图.pdf》由会员分享,可在线阅读,更多相关《Alto_AMX-140FX-USB_Mixer_Service_Manual电路图.pdf(35页珍藏版)》请在收音机爱好者资料库上搜索。
1、RadioFans.CN 收音机爱 好者资料库 MODEL: AMX 140FX-USB CONTENT 1. INTRODUCTION.1 2. TECHNICAL SPECIFICATION.2 3. BLOCK DIAGRAM.45 4. SCHEMATIC DIAGRAM.57 5. WIRING DIAGRAM.131 1 6. PCB LAYOUT.141 3 7. TEST PROCEDURE.181 9 8. EXPLODED VIEW and be sure the potentiometer knob has no frication. 4. Functional Test
2、: 1). After the surface testing is OK, input proper AC power voltage, open the main power switch, POWER led will light up (green). Then open the PHANTOM switch, the PHANTOM led will light up (red), it has 46V (2V) PHANTOM voltage of the second and third pin on each MIC MIC1, MIC2, MIC3, MIC4, MIC (M
3、ONO) which had been tested by voltmeter. At last, close the switch (Note: we should close this switch, or the instruments will be damaged). 2). Adjust all the TRIM knob to min, the LEVEL, EQ, AUX knob to 0, and the PAN to mid, turn all the keys to OFF. 3). Connect the balanced input to MIC MIC1, MIC
4、2, MIC3, MIC4, MIC (MONO), connect - 18 - the unbalanced input to LINE IN 5/6, rotate the PAN knob of the corresponding channel on LINE IN 7/8 to LEFT or RIGHT, a. The unbalanced output of AUX1, AUX2 which has tested is +2dBu (2dB) THD+N=0.005%; b. Adjust the AUX1, AUX2 knob to min, the unbalanced o
5、utput (LEFT 5). Connect the unbalanced input to AUX RETURN1, the balanced output (LEFT 6). Connect the RCA terminal to L the LED LEVEL indicator will light up in return. The MAIN MIX OUTPUT (LEFT the PEAK led will light up (red). Use the same way to test and see if the corresponding PEAK led of CHAN
6、NEL2CHANNEL4 in normal. 5. Frequency Response Test: Input signal from LINE1, LINE2, LINE3, LINE4, LINE5, LINE6, the output frequency curve on MAIN MIX OUTPUT (LEFT rotate the corresponding channel of EQ LOW to min (-15) in counterclockwise, and the output is -15dBu (2dB); 2). Change the input freque
7、ncy to 2.5KHz, rotate the corresponding channel of EQ MID knob to max (+12) in clockwise, and the output is +12dBu (2dB); rotate the corresponding channel of EQ MID to min, and the output is -12dBu (2dB); 3). Change the input frequency to 12KHz, rotate the corresponding channel of EQ HIGH to max (+1
8、5) in clockwise, and the output is +15dBu (3dB). 6. The effect of DSP: 1). Input signal from MIC1 to MIC4, output signal from MAIN MIX OUTPUT, rotate the AUX RTN2 (DFX) to max in clockwise, rotate the PRESETS and ARATION knob, it will appear the signal which has been processed by DSP, if the INPUT s
9、ignal is larger, the PEAK will light up (red), press the DFX MUTE key, it will appear the BYPASS signal. 2). Input signal from MIC1 to MIC4, output signal from AUX SENDS1, rotate the AUX2 to min, rotate the AUX1, AUX RTN2 (DFX), AUX2/DFX TO AUX1 to max in clockwise, rotate the PRESETS and ARATION kn
10、ob, it will appear the signal which has been processed by DSP, if the INPUT signal is larger, the PEAK led will light up (red), press the DFX MUTE key, it will appear the BYPASS signal. 7. USB Test: 1). Set the MAIN MIX LEVEL, PHONES/CONTROL ROOM, EQ, PAN, BAL knob to 0, the TRIM, AUX1, AUX RTN1, AU
11、X RTN2 (DFX), AUX2/DFX TO AUX1, 2TK IN to min, rotate the PAN on CH1 to LEFT, the PAN knob on CH2 to RIGHT, and turn the entire -21 - keys to OFF. 2). Input 0dBu to AP, connect the balanced input to MIC1, MIC2, rotate the LEVEL on CH1 CH2 to max, and connect the unbalanced output to MAIN MIX OUTPUT,
12、 the output is +10dBu (2dB) THD+N0.005%. 3). Switch the USB RECORD to CH1/2, the USB PLAYBACK to MAIN MIX, and connect the USB line to PC. Open the recorder to tape for 60 seconds: 4). Take off the input signal, and press the playing key, the output is +10dBu (2dB) THD+N0.1%. 5). Input 0dBu to AP, c
13、onnect the balanced input to MIC1, MIC2, rotate the LEVEL on CH1, CH2 to max, the balanced output to MAIN MIX OUTPUT, and the output is +10dBu (2dB) THD+N0.005%. 6). Switch the USB RECORD to MAIN MIX, the USB PLAYBACK ot CH7/8, and connect the USB line to PC. Open the recorder to tape for 60 seconds
14、: 7). Take off the input signal, press the LINE/USB on CH11/12, rotate the CH LEVEL to 0, press the playing key, and the output is +4dBu (2dB) THD+N5%. - 22 - 8). Open the C:ApwinS2A-A FFT. At2 and set as following picture: 9). Do not input signal, connect the unbalanced output to MAIN MIX OUTPUT, s
15、witch the USB RECORD to MAIN MIX, the USB PLAYBACK to MAIN MIX, connect the USB line to PC. Open the recorder to tape for 60 seconds: 10). After recording, press the playing key, the AP will start to scan, the waveform of the picture has not changed much, and connect the high quality amplifier and s
16、peaker to see if it will appear high frequency sounding. - 23 - 8. Selecting Check: connect the AMX-140FX USB to high quality amplifier and speaker, to see if it will appear abnormal noise. 9. Factory Presets: rotate the entire volume control knob to min, the other control knob to mid, and turn the
17、entire switch OFF. - 24 - 8. EXPLODED VIEW 140FX-V1.01 2 MG00061 screw-RSM3*1018 3 MA05704 ZC-panelAMX-140FX USB ALTO-V1.41 4 HK06378 K-PC boardP-AMX140FX-USB-DIP1 5 HK06381 K-PC boardAMX-USB-DIP1 6 HK06352 K-PC boardP-DSP-PRE-DIP1 7 HK01409 K-PC boardP-313123-DIP(AMX-140FX)1 8 MG00243 copper pillar
18、-RSM3*5*0.5PH3 9 MG00326 screw-RSM3*45 10 NI02620ZD-insulator board-L8-041*86.5*53 L-81 11 MI01953 ZD-heat sink-AMX100FX-02AMX-100FX 1.5t*24*21*20.5mm1 12 MG00162 nickel screw-RSM3*84 13 MF00037 spring washer3.2*5.5*1t7 14 NI02249insulator-RSTW-1 (TO-220)4 15 NC00005 sheet mica-RSSB-9500DSP 18*13*0.
19、1t-V1.04 16 ME00015 color nut-RS3mm4 17 MG00041 screw-RSM3*628 18 MI03094ZD-heat sink-AMX100FX USB-02AMX-140FX USB 1t*87.5*123-V1.11 19 NI00826plastic knob-RS-C12*18mm dual 6 20 NI02082plastic knob-RS-C10.5*18mm dual6 21 NI02081plastic knob-RS-C10.5*18mm dual7 22 NI02083plastic knob-RS-C10.5*18mm du
20、al18 23 NI02714plastic knob-RS-C10.5*13.5mm dual5 24 MF00061 washer9.6*13*0.5t24 25 MF00060 MIC jack nut-HC00125JY-6351G-02-25024 26 NI02836Lens-RS-C10*7*3mm AMX-1401 27 NI02386plastic knob-RS-C14*13mm dual2 28 NI01863key-RS5.5*W10*7.5 black8 29 NI02817plastic knob-RS-C10.5*18mm dual2 30 NI02633plas
21、tic knob-RS-C10.5*18mm dual8 31 HI00026power switch-RSRA12KKATOF 2P1 32 HI00171power switch-RSR612KKATOF 11 33 HC00601 DC socket-RSSCD554CCS0030001 34 NI00378plastic washer-RS-C9*13 used to PU socket1 35 NC00037 ZD-washer-XM1602-071t*8*12.5mm XM1602-V1.01 36 ME00143 nickel screw-HC0060110 5/6 *32W1
22、37 MJ01317 ZC-fixed boardAMX-140FX USB-V1.21 38 MB04519 ZCC-chassisAMX-140FX USB-V1.11 39 NI00498self-adhere foot cushion-RS12.7*7*6mm (SF-005)4 40 NI01862key-RS-C5.5*5.5*14.5-V1.15 41 NI02837plastic knob-RS-C-ABS35*11mm 534C1 PARTS LIST - 26 - No. Part No.DescriptionSpecificationRemark 1TG00203tran
23、sformer-RS-T230V/50Hz-AC18V/1200mA-EI48 2NE15392lableAMX-140FX USB_V1.0 3NI00014membrane0.035*1M 4NH00012bond paper0.04*1M 5NF02624user manual-RSAMX-140FX USB ALTO_V1.0 6NI00826knob12*18mm double color 7NI00252sleeve4*20mm 8NI00248sleeve4*1000mm 9NI00498self-adhere foot cushion12.7*7*6mm(SF-005) 10
24、NI00378plastic washer9*13 used to PU socket 11 NI03064handleAMX-140;140FX_V1.0 12 NI02835handle269*33*26mm AMX-140 black 13 NI02837knob35*11mm 534C 14 NI02836acrylic panel10*7*3mm AMX-140 15 NI02714knob10*13.5mm 16 NI02633knob10.5*18 17 NI02386konb14*13mm 18 NI01863key-RS5.5*W10*7.5 19 NI01862key5.5
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Alto_AMX-140FX-USB_Mixer_Service_Manual 电路图 Alto_AMX 140 FX USB_Mixer_Service_Manual
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


