Ampeg_SVT-2_PRO,_CL_Output_Tube_Life_Tech_Information电路图.pdf

《Ampeg_SVT-2_PRO,_CL_Output_Tube_Life_Tech_Information电路图.pdf》由会员分享，可在线阅读，更多相关《Ampeg_SVT-2_PRO,_CL_Output_Tube_Life_Tech_Information电路图.pdf（5页珍藏版）》请在收音机爱好者资料库上搜索。

1、Technical Information Bulletin SLM Electronics, Inc. Saint Louis, Missouri, USA TIB0003SVT2PRO/SVTCL/SVTAV Power Tube Board Modificationpage 1 of 5 June 4, 2001#TIB0003 Units Affected: ModelSerial NumbersModelSerial Numbers SVT-2PROT2PDxxxxxxxxxSVTAVAXVDxxxxxxxxx ATLDxxxxxxxxx BJIDMAxxxxxxx SVT-2PRO

2、JT2PJxxxxxxxxxSVTAVJBAHJxxxxxxxxx ATLJxxxxxxxxx BJJJMAxxxxxxx SVT-2PROUATLUxxxxxxxxxSVTAVUBAIUxxxxxxxxx BJKUMAxxxxxxx SVT-2PROWT2PWxxxxxxxxxSVTAVWAXVWxxxxxxxxx ATLWxxxxxxxxx BJMWMAxxxxxxx SVT-CLTCLDxxxxxxxxxSVT-CLJTCLJxxxxxxxxx BCYDxxxxxxxxxBCYJxxxxxxxxx BJNDMAxxxxxxxBJOJMAxxxxxxx SVT-CLWTCLWxxxxxxx

3、xx BCZWxxxxxxxxx Purpose: (1) To extend the life of the amplifiers power tubes. Recommended Actions: (1) Remove six 1N4007 diodes from power amp tube circuit. (2) Replace six 22 ohm resistors in power amp tube circuit with 220 ohm, 1/2W 5% flame-proof resistors (SLME p/n 77-221-03). Tools Needed: #2

4、 phillips screwdriver 5/64” allen wrench wire cutters soldering iron solder CAUTION! DISCONNECT THE AMPLIFIER FROM ANY SOURCE OF AC POWER BEFORE PROCEEDING! RadioFans.CN 收音机爱 好者资料库 Technical Information Bulletin SLM Electronics, Inc. Saint Louis, Missouri, USA Corrective Action: SVT-2PRO: (1) Place

5、the amplifier on the work surface, right side up, front panel facing you. (2) Remove the 12 screws from the top cover. Remove the top cover and set it aside. Proceed to step 7. SVT-CL/SVT-AV: (1) Place the amplifier on the work surface, on one end, cabinet bottom facing you. (2) Remove four of the f

6、ive large bolts from the bottom of the cabinet, leaving the upper bolt in place. (Refer to the adjacent picture.) (3) Lower the amplifier onto its feet on the work sur- face. Position the amplifier so the end with the remaining bolt hangs over the edge of the work sur- face. (Refer to the adjacent p

7、icture.) Remove the remaining bolt from the bottom of the cabinet. (4) Reposition amp on work surface, right side up, front panel facing away from you. (5) Remove the seven screws from the rear grille screen. Remove the screen and set it aside. (6) Slowly and carefully work the amplifier assembly ab

8、out 2/3 of the way out of the cabinet far enough to allow access to the tubes and the tube board. Avoid putting excessive strain on the con- necting cables! (7) Grasp one of the power tube retainers by its top ring. Lift the retainer up and away from the power tube, then slowly lower it to the plate

9、 at the base of the tubes as shown in the adjacent pictures. Repeat for the remaining tube retainers. TIB0003SVT2PRO/SVTCL/SVTAV Power Tube Board Modificationpage 2 of 5 RadioFans.CN 收音机爱 好者资料库 Technical Information Bulletin SLM Electronics, Inc. Saint Louis, Missouri, USA CAUTION: The tension on th

10、e retainerssprings may cause them to snap back towards the base of the tubes, possibly cracking their glass casings - slowly lower each retainer down to the base of the tubes to avoid such damage. (8) Carefully remove each of the power tubes by gently rocking it side to side while lifting it straigh

11、t up. Set the tubes aside. (9) Each tube retainer is secured to the tube socket with two 5/64” allen head screws. Remove the screws, then remove the tube retainers and set them aside. (10) Remove the eight screws from the tube plate. Remove the tube plate and set it aside. (11) Lift the power tube c

12、ircuit board assembly up slightly and disconnect the white two-wire connector from the two-pin header on the edge of the board as shown in the adjacent picture. (12) Lift the tube board assembly further up until the ribbon connector beneath it is accessi- ble. Disconnect the ribbon connector from th

13、e multi-pin header on the circuit board beneath as shown in the adjacent picture. (13) Disconnect the remaining five wires from the underside of the tube board assembly. Place the tube board assembly on the work surface so the printing reads right side up. (14) Locate, cut and remove the six 1N4007

14、diodes (D1, D2, D3, D7, D8, D9) from the tube board. (These are located in the high- lighted areas of the adjacent picture.) (15) Locate, desolder and remove the six 22 ohm resistors (R2, R4, R6, R7, R9, R11) from the tube board. (These are also located in the highlighted areas of the adjacent pictu

15、re.) TIB0003SVT2PRO/SVTCL/SVTAV Power Tube Board Modificationpage 3 of 5 RadioFans.CN 收音机爱 好者资料库 Technical Information Bulletin SLM Electronics, Inc. Saint Louis, Missouri, USA TIB0003SVT2PRO/SVTCL/SVTAV Power Tube Board Modificationpage 4 of 5 (16) Install a 220 ohm 1/2 watt 5% flame proof resistor

16、 (SLME p/n 77-221-03) in place of each resis- tor removed in step 15. (17) Return the tube board assembly to its place in the amplifier. Connect the five wires to the tabs on the underside of the circuit board as shown in the adjacent picture. (18) Carefully reconnect the ribbon cable to the multi-p

17、in header on the circuit board beneath the tube amp board. Make certain that the connector is properly aligned and oriented with the header as shown in the adjacent picture so that all of the pins mate into the connector. (19) Reconnect the white two-wire connector to the two-pin header on the edge

18、of the tube board. (20) Rest the tube board assembly in place and set the tube plate over the board assembly so the tube sockets line up with the large holes in the plate. (21) Install each of the tube retainers. Orient the tabs of the retainers so their elevated tabs (where the springs are attached

19、) are furthest from the socket as shown in the adjacent picture. (22) Install the eight screws which secure the tube plate and tighten them firmly. (23) Replace each of the power tubes into the tube sockets and secure each one with its tube retainer. SVT-2PRO: (24) Replace the top cover and install

20、the 12 screws which secure it to the amplifier chassis. Tighten the screws firmly. Proceed to step 28. SVT-CL/SVT-AV: (24) Carefully return the amp assembly into its original position within the cabinet. Push the chassis all the way into the cabinet. Technical Information Bulletin SLM Electronics, I

21、nc. Saint Louis, Missouri, USA A Division of St. Louis Music, Inc. 11880 Borman Drive St. Louis, MO 63146 Phone (314) 569-0141 Fax (314) 567-7278 Service Department (800) 738-7563 TIB0003SVT2PRO/SVTCL/SVTAV Power Tube Board Modificationpage 5 of 5 (25) Turn the cabinet so one end hangs over the edge

22、 of the work surface. (Refer to the adjacent picture.) Insert one of the large bolts into the mounting hole in the cabinet. Work the bolt and the amplifier around as needed until the bolt threads into the amp chassis. Avoid cross-threading the bolt! Tighten the bolt securely into the amplifier. (26)

23、 Stand the amplifier on one end, with the bolt installed in step 25 towards the top. Insert the remaining four bolts into their mounting holes and thread them into the chassis. Avoid cross-thread- ing the bolts! Tighten each bolt securely. (27) Replace the rear grille screen and install the seven sc

24、rews which secure it to the cabinet. Tighten each screw firmly. (28) Connect the AC line cord and turn the amplifier on. Verify illumination of the front panel LED. Look through the rear grille and verify each power tube glows slightly near its top. (If the LED does not illuminate, or if the power tubes do not have a slight glow, disconnect the AC line cord, open the unit up and double check all wiring. If the problem persists contact your Ampeg Service Center.) (29) Repack the amplifier into its original shipping carton.