Audix_D4_Specifications电路图.pdf
《Audix_D4_Specifications电路图.pdf》由会员分享,可在线阅读,更多相关《Audix_D4_Specifications电路图.pdf(2页珍藏版)》请在收音机爱好者资料库上搜索。
1、D4 OVERVIEW: Designed, machined, assembled and tested by Audix in the USA, the D4 is a dynamic instrument microphone used for stage, studio and broadcast applications. The D4, which is characterized with a hypercardioid pickup pattern for isolation and feedback control, is equipped with a VLM (Very
2、Low Mass) diaphragm for natural, accurate sound reproduction. The D4 is lightweight, compact and easy to position. With a wide frequency response of 40 Hz - 18 kHz and the ability to handle sound pressure levels in excess of 144 dB, the D4 is an excellent choice for miking instruments requiring prec
3、ise low frequency reproduction such as large rack toms, floor toms, cajon, djembe, tympani, leslie bottom, bass flute, sax and baritone sax, trombone, acoustic bass, bass cabs and small kick drums. Roadworthy construction includes a precision machined aluminum body, black anodized finish, laser etch
4、ed model and serial number, steel mesh grill, Switchcraft XLR connector and includes a tension-fit heavy duty nylon mic clip. Transformerless design, low impedance, and balanced output allow for interference-free performance even with long cable runs. APPLICATIONS: Floor toms Kick Drum Bass Cabinets
5、, Leslie Bottom Djembe, Cajon, Digeridoo Piano Sax, Trombonem Clarinet Studio - Any instrument requiring precise low frequency reproduction DYNAMIC INSTRUMENT MICROPHONE D4 SUPPLIED ACCESSORIES: Tension-fit heavy duty nylon mic clip (DCLIP) Carrying pouch (P1) OPTIONAL ACCESSORIES: TRIPOD - Tripod m
6、ic stand DFLEX - All purpose percussion clamp DVICE - Spring loaded rim mount clamp DCLAMP - Tension rod mic clamp CBL-20 - 20 XLR-XLR mic cable CBL-DR25 - 25 right angle XLR-XLR mic cable STAND-KD - Adjustable kick drum mic stand CAB GRABBER - Tension held mic holder, clamps to guitar cabinets DCLA
7、MP DFLEX DCLIP CAB GRABBER STAND-KD FEATURES: Compact, lightweight Machined aluminum body VLM (very low mass) diaphragm Studio quality sound Excellent mid-bass transient response Handles extremely high SPL without distortion Roadworthy construction 5 year warranty Dynamic Instrument RadioFans.CN 收音机
8、爱 好者资料库 SPECIFICATIONS: ARCHITECTS AND ENGINEERS SPECIFICATIONS: The microphone shall be of the dynamic type operating on the moving coil principle and the capsule shall be VLM Type D. The polar pattern of the microphone shall be hypercardioid. The nominal output impedance shall be 200 ohms at 1 kHz
9、.The microphone shall have a sensitivity of 1.4 mV / Pa at 1 kHz and will handle a sound pressure level of 144 dB. The microphone body shall be machined of aluminum and the grill cap shall be steel wire mesh. The overall dimensions shall be 21.5 mm in diameter at the base, 39 mm in diameter at the w
10、idest point on the grill and 100 mm in length. The microphone shall be the Audix D4. Call: 503-682-6933 Fax: 503-682-7114 Audix Corporation 9400 SW Barber Street, Wilsonville, OR 97070 Transducer Type Dynamic Frequency Response 40 Hz - 18 kHz Polar Pattern Hypercardioid Output Impedance 200 ohms Sen
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Audix_D4_Specifications 电路图
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


