Audix_D2_Specifications电路图.pdf

《Audix_D2_Specifications电路图.pdf》由会员分享，可在线阅读，更多相关《Audix_D2_Specifications电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、D2 OVERVIEW: Designed, machined, assembled and tested by Audix in the USA, the D2 is a dynamic instrument microphone used for stage, studio and broadcast applications. The D2 is characterized with a hypercardioid pickup pattern for isolation and feedback control and is equipped with a VLM (Very Low

2、Mass) diaphragm for natural, accurate sound reproduction. The D2 is lightweight, compact and easy to position. With a wide frequency response of 80 Hz - 18 kHz and the ability to handle sound pressure levels in excess of 144 dB, the D2 is an excellent choice for miking instruments with a percussive

3、nature such as rack toms, congas, saxophone, guitar cabinets and brass. Roadworthy construction includes a precision machined aluminum body, black anodized finish, laser etched model and serial number, steel mesh grill, Switchcraft XLR connector and includes a tension-fit heavy duty nylon mic clip.

4、Transformerless design, low impedance, and balanced output allow for interference-free performance even with long cable runs. APPLICATIONS: Rack toms, congas, floor tom Guitar and bass cabinets Saxophone, brass SUPPLIED ACCESSORIES: Tension-fit heavy duty mic clip (DCLIP) Carrying pouch (P1) OPTIONA

5、L ACCESSORIES: TRIPOD - Mic stand DFLEX - All purpose percussion clamp DVICE - Spring loaded rim mount clamp DCLAMP - Tension rod mic clamp CBL-DR25 - 25 right angle XLR cable STAND-KD - Adjustable short boom mic stand CAB GRABBER - Tension held mic holder, clamps to guitar cabinets DYNAMIC INSTRUME

6、NT MICROPHONE D2 Dynamic Instrument DCLAMP DFLEX DVICE & CBL-DR25 w/ D2 CAB GRABBER STAND-KD FEATURES: Compact, lightweight Machined aluminum body VLM (very low mass) diaphragm Studio quality sound Excellent mid-bass transient response Handles extremely high SPL without distortion Roadworthy constru

7、ction 5 year warranty RadioFans.CN 收音机爱 好者资料库 Transducer Type Dynamic Frequency Response 80 Hz - 18 kHz Polar Pattern Hypercardioid Output Impedance 250 ohms Sensitivity at 1k 1.2 mV / Pa Capsule Technology VLM Type B Off Axis Rejection 30 dB Maximum SPL 144 dB Power Requirements None Connector Swit

8、chcraft male XLR connector Polarity Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector Housing / Finish Machined Aluminum / Black Hard Coat Weight 128 g / 4.5 ounces Length 100 mm / 3.9 inches SPECIFICATIONS: ARCHITECTS AND ENGINEERS SPECIFICA

9、TIONS: The microphone shall be of the dynamic type operating on the moving coil principle and the capsule shall be VLM Type B. The polar pattern of the microphone shall be hypercardioid. The nominal output impedance shall be 250 ohms at 1 kHz.The microphone shall have a sensitivity of 1.2 mV / Pa at

10、 1 kHz and will handle a sound pressure level of 144 dB. The microphone body shall be machined of aluminum and the grill cap shall be steel wire mesh. The overall dimensions shall be 21.5 mm in diameter at the base, 39 mm in diameter at the widest point and 100 mm in length. The microphone shall be

11、the Audix D2. Call: 503-682-6933 Fax: 503-682-7114 Audix Corporation 9400 SW Barber Street, Wilsonville, OR 97070 SERVICE AND WARRANTY: This microphone is under warranty for a period of 5 years from any and all manufacturing defects. Should your microphone fail in any way, please contact the Audix S

12、ervice department at 503-682-6933. A Return Authorization number is required before returning any products. CARE AND MAINTENANCE: The D2 is manufactured to exacting specs with roadworthy construction. However, the capsule is highly sensitive and should be handled with care. Avoid extreme temperature

13、s and be sure to store your microphone in the pouch provided when not in use. Moisture of any kind can adversely affect the sound and performance of your microphone. OPERATION: The D2 is a low impedance microphone and should be plugged into a “mic level” of your console, mixer, or recording device.

14、Please note that your microphone does not require phantom power and will not be effected in any way by phantom power should it be running simultaneously while the microphone is in operation. Avoid plugging or unplugging the microphone from the PA system unless the channel is muted or the volume of t

15、he system turned down. Failure to do so may result in a loud “popping” noise which could seriously damage the speakers in the PA system. USER TIPS: The D2 has an extremely tight (hypercardioid) pick-up pattern in order to help eliminate sound from other instruments on stage from “bleeding” into the

16、microphone. For this reason, it the D2 is exceptionally effective in capturing the sound of each component of a drum or percussion kit. Drums, hand percussion: As a general rule, the bottom of the D2 grill should be 1-2 inches above the head of the drum and pointed towards the center. For more “ring

17、” pull the mic back towards the rim. For less ring and more overtones, position the mic 1-2 inches inside the ring. For more attack, place the mic very close to the head and for more overtones and decay move the mic further away from the head. Guitar cabinets: The D2 can be placed within 1-2 inches

18、of the grill cover at a 90 degree angle pointing directly into the speaker. If the mic is placed closer to the edge of the speaker, you will minimize the higher frequencies and get a warmer, fatter tone. To capture more highs, move the mic closer towards the center of the speaker, but avoid the midd

19、le of the speaker. Horns: Place the mic within 1-2 inches of the bell, especially when on a stage with drums, bass, guitar, etc. For jazz, classical, and music where the stage volume is lower, the mic can be placed further away for a richer, fuller sound. *Further miking techniques may be found on our website at FREQUENCY / POLARS: *All specifications subject to change without notice. To register your microphone, please visit DIMENSIONS (mm): D2 RadioFans.CN 收音机爱 好者资料库