EV_CPS3,_CPS4_Power_Amp_Owners_Manual电路图.pdf

《EV_CPS3,_CPS4_Power_Amp_Owners_Manual电路图.pdf》由会员分享，可在线阅读，更多相关《EV_CPS3,_CPS4_Power_Amp_Owners_Manual电路图.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、 OWNERS MANUAL CPS 3 / CPS 4 CONTRACTOR PRECISION SERIES RadioFans.CN 收音机爱 好者资料库 The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitud

2、e to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance (servicing) instructions in the literature accompanying the appliance. IMPORTANT SAFETY INSTRUCTIONS 1. Read th

3、ese instructions. 2. Keep these instructions. 3. Heed all warnings. 4.Follow all instructions. 5. Do not use this apparatus near water. 6.Clean only with a damp cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufactures instructions. 8.Do not install near any

4、 heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. 9.Only use attachments/accessories specified by the manufacturer. 10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power

5、-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. For US and CANADA only: Do not defeat the safety purpose of the grounding-type plug. A grounding typ

6、e plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrican for replacement of the absolete outlet. 1. Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65)

7、 and the CSA E65 - 94 have to be obeyed when servicing the appliance. 2. Use of a mains separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is connected to the mains 3. Switch off the power before retrofitting any extensions, changing the mai

8、ns voltage or the output voltage. 4. The minimum distance between parts carrying mains voltage and any accessible metal piece (metal enclosure), respectively between the mains poles has to be 3 mm and needs to be minded at all times. The minimum distance between parts carrying mains voltage and any

9、switches or breakers that are not connected to the mains (secondary parts) has to be 6 mm and needs to be minded at all times. 5. Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original parts. 6. Altering the circui

10、try without prior consent or advice is not legitimate. 7. Any work security regulations that are applicable at the location where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations about the work place itself. 8. All instructions concerning the handling

11、of MOS - circuits have to be observed. Note: SAFETY COMPONENT (HAS TO BE REPLACED WITH ORIGINAL PART ONLY) IMPORTANT SERVICE INSTRUCTIONS CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that

12、contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. 8 RadioFans.CN 收音机爱 好者资料库 CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front P

13、anel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Specifications. . . . . . . . . . . . . . .

14、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15、. . . . . . . . . . . . . . . . . . . . . . 21 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DESCRIPTION First of all, we would like to express our thanks and at the same time congratulate you on the decision to b

16、uy one of our CONTRACTOR PRECISION SERIES power amplifiers. Electro-Voice CONTRACTOR PRECISION SERIES amplifiers are made to meet the highest require- ments of any on-the-road application. Thus they provide on-board protection against thermal and capacitive overload, short-circuit and the occurrence

17、 of HF or DC at the output. Additionally, special circuitry prevents the output-stage transistors from being damaged by Back-EMF. During soft start, delayed switching of the power outputs is accomplished via relays and a limiter controls the initial current inrush, preventing the mains fuse from bei

18、ng blown during the power-on operation. The mechanical construction as well is carried out following the highest precision standards of the industry. The robust steel chassis provides extreme rigidity and it is meant to live through any hard wearing condition of a touring application. Thermal stabil

19、ity is guaranteed by two 4-Mode silently running fans that offer the possibility to also use the amplifiers in a studio environment. The extensive comparator circuitry constantly monitors the input and output signals and activates the internal limiters whenever a non-linear operational state is enco

20、untered. This provides reliable protection of the connected loudspeaker systems against overload and clipping. The sound quality of the CON- TRACTOR PRECISON SERIES power amplifiers is superb. Using comprehensive dimensioned power supply units with low-interference toroidal transformers gains a head

21、room that exceeds the nominal power handling capacity by far. No V/I-Foldback-Limiter circuits are employed within the power amplifiers, making it possible to operate the amps on complex loads up to 90 phase angles without a problem. The input facilities are carried out as balanced XLRF-type sockets

22、 while the Direct-Outs on which the carried-through signals are present come as XLRM-type connectors. Using the Input Routing-switches lets you determine if the CONTRACTOR PRECISION SERIES amplifiers are operated in DUAL (stereo) or PARALLEL (monaural) mode; “mono-bridged” operation is also possible

23、. The dB-scaled level controls are to be found on the rear panel. These potentiometers guarantee precise and reliable operation. The easy readable LED display offers quick optical information on the power amplifiers momentary operational mode. For each channel individually the display shows whether

24、they are operational, a signal is present at the outputs, when the limiters are activated, and whether one of the protection circuits has been engaged or not. The power outputs CANNEL A, CHANNEL B and BRIDGED OUT are carried out as Speakon connectors. A ground-lift switch that separates the enclosur

25、e from the appliances ground potential and therefore helps to eliminate ground noise loops and the mono bridged mode switch are also located on the rear panel. In normal operation all CONTRACTOR PRECISION SERIES power amplifiers can be used to drive loads down to 2 ohms; in bridged mode the minimal

26、load is 4 ohms. All amps are equipped with extremely silent running fans providing front-to-rear air circulation, guaranteeing trouble-free operation even in smaller power amplifier rack systems. Studying this owners manual carefully will provide you with further and more detailed information about

27、the CONTRACTOR PRECISION SERIES power amplifiers. Thus we recommend to keep on reading, assuring you that the Electro-Voice CONTRACTOR PRECISION SERIES power amplifiers will provide you with a lot of fun and satisfaction in your work. DESCRIPTION 9 RadioFans.CN 收音机爱 好者资料库 1. Level Control To prevent

28、 unauthorized operation of the level controls on the CPS3 and CPS4, they are provided with screwed-on protective cover lids. When shipped from the factory, the detented potentiometers are set to their clockwise limits. Thus, the input signal is not attenuated. In case matching the input levels is re

29、quired, you first have to detach (unscrew) the cover lids to gain access to the potentiometers. 2. POWER ON INDICATION This LED lights up when the mains switch is pressed. If it does not light up, the unit is not connected to the mains or the mains fuse has blown. 3. INPUT INDICATION This LED lights

30、 up if a signal is present at the power amplifier input. The indicator does not light up when the input controls are turned down completely. 4. OUTPUT INDICATION This LED lights up if a signal is present at the power amplifier output. The indicator goes off when the speaker line has shorted or a pro

31、tective circuit has been activated thus indicating that there is no signal at the speaker output terminals. 5. LIMIT This LED lights up if the limiter has been activated and the power amplifier is being operated at the clip level. If the LED flashes briefly, this is not a cause for concern. If this

32、LED is lit permanently, the volume should be reduced to avoid overload damages to the connected loudspeaker systems. 6. PROTECT When this LED lights up during operation, one of the protection circuits against over-temperature, overload, shorted outputs, radio frequency interference or DC faults has

33、been triggered. The cause of the error e.g. a shorted loudspeaker line must be remedied. In case of overheating, wait a little until the amplifier switches back to operating mode itself. 7. POWER Switch The unit is switched on via the power switch. The loudspeaker outputs are switched on via delayed

34、 relays so that no startup transients are audible. A current limiter prevents startup peaks on the mains line and prevents the mains fuse from blowing. FRONT PANEL 10 POWER AMPLIFIER INPUTS Parallel to the XLR-type inputs, output connectors are provided, offering the opportunity to feed additional p

35、ower amplifiers with the same signal. The inputs are electrically balanced with pin-assignment according to the IEC 268 standard. Pin-assignment of the XLR-type input connectors: Input sensitivity is factory set to 0 dBu. The power amplifier can be set internally to +6dBu input sensitivity or to +26

36、dBu gain. INPUT ROUTING PARALLEL MONAURAL Setting the selector switch to the PARALLEL/MONO position puts the channel A and channel B inputs in electrically direct parallel configu- ration, leaving you still the possibility to control the channels level settings separately, using the output controls

37、A and B. DUAL STEREO When the selector switch is set to its DUAL/STEREO position both channels are amplified individually. PIN 1: SHIELD PIN 2: a, + PIN 3: b, - REAR PANEL 11 POWER AMPLIFIER OUTPUT CONNECTORS SPEAKON output connectors are provided for the power amplifier channels A (left) and B (rig

38、ht). The Bridged Out Connector for bridged operation is sealed with a plastic cover to prevent connection errors. LIMITER The time constant of the built-in limiter to avoid overdri- ving is adjustable. Position “SLOW” is the factory preset and this should also be the normal position. If the power am

39、plifier is used as a MID/HI-frequency amplifier in active multi-way systems, the limiter switch should be set to “FAST”. If the power amplifier is used as LOW-frequency ampli- fier in active multi-way systems, the limiter switch should be set to “SLOW”. BRIDGED MODE Slide switch to change from Norma

40、l Stereo mode to Bridged mode. In Bridged mode the built-in power ampli- fiers operate in “push- pull” and the double output voltage from channel A and B appears at the Bridged output connector. The phases of Channel A and B are in oppo- site and therefore the individual channels must not be used as

41、 loudspeaker outputs. HI-LO-CUT FILTER This filter attenuates subsonic and high frequency si- gnals so that the power amplifiers are not modulated with these signals. This switch should normally always be in position ON. The OFF position is only for applications where an upstream unit, e.g. a crosso

42、ver or a equalizer, has integrated HI-Cut and LO-Cut filters. GROUNDLIFT SWITCH Hum loops can be avoided with the groundlift switch. If the power amplifier is operated together with other units in one 19 rack, the switch should be in GROUNDED position. If the power amplifier is used with units which

43、 have different earthing potentials, the switch should be adjusted to the UNGROUNDED position. REAR PANEL 12 Technical Specifications: CPS3, CPS4 Amplifier at rated conditions, both channels driven with 8 ohms loads, unless otherwise specified. CPS3 CPS4 Load Impedance 8 4 2 8 4 2 Maximum Midband Ou

44、tput Power 560W900W 1200W 850W1300W 1800W THD=1%, 1kHz Rated Output Power 500W800W 1000W 750W1200W 1500W THD 0.1%, 20Hz . 20kHz Maximum Bridged Output Power1800W 2400W 2600W 3600W THD=1%, 1kHz Maximum RMS Voltage Swing 72V 91V THD=1%, 1kHz Voltage Gain37dB 39dB at 1 kHz Slew Rate 35V/s 40V/s Power C

45、onsumption1300W 1850W at 1/8 maximum output power 4 Input Sensitivity 0dBu ( 775mV) at rated output power 4 , 1 kHz THD at rated output power, 0.05 % MBW=80kHz, 1 kHz IMD-SMPTE 0.01 % 60 Hz, 7 kHz DIM30 0.01 % 3.15kHz, 15 kHz Crosstalk 400 / 300 Signal to Noise Ratio A-weighted 105dB Power Requireme

46、nts 230V, 50Hz . 60Hz ProtectionAudio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn-on delay Cooling Front-to-Rear, 4-stage-fans Safety Class I Dimensions (W x H x D), mm483 x 132.5 x 385.5 Weight27kg 29kg Retrofitting kit Input Transformers NRS 9

47、0176 SPECIFICATIONS 13 BLOCK DIAGRAM 20 Abmessungen/Dimensions (in mm) ABMESSUNGEN/DIMENSIONS 21 WARRANTY (Limited) Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual product-line statement(s) below,

48、 or in the individual product data sheet or owners manual, beginning with the date of original purchase. If such malfunction occurs during the specified period, the product will be repaired or replaced (at our option) without charge. The product will be returned to the customer prepaid. Exclusions a

49、nd Limitations: The Limited Warranty does not apply to: (a) exterior finish or appearance; (b) certain specific items described in the individual product-line statement(s) below, or in the individual product data sheet or owners manual; Malfunction resulting from use or operation of the product other than as specified in the product data sheet or owners manual; (d): malfunction resulting from misuse or abuse of the product; or (e): malfunction occurring at any time after repairs have been made to the product by anyone o