General_Music_RPT114_Bachman_Service_Manual电路图.pdf
《General_Music_RPT114_Bachman_Service_Manual电路图.pdf》由会员分享,可在线阅读,更多相关《General_Music_RPT114_Bachman_Service_Manual电路图.pdf(10页珍藏版)》请在收音机爱好者资料库上搜索。
1、1 o CODE : 270209 Index & Warnings Soldering point. Male connector. Female connector. M/F faston connector. Test point. Supply voltage. Logic supply ground. Analog supply ground. Signal ground. Chassis ground. Flag joined with one or more flags with the same signal name inscribed. Notice Service mus
2、t be carried out by qualified personnel only. Any tampering carried out by unqualified personnel during the guarantee period will forfeit the right to guarantee. For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again. To
3、improve the devices specifications, the schematic diagrams may be subject to change without prior notice. ATTENTION Observe precautions when handling electrostatic sensitive devices SERVICE MANUAL Schematic Diagrams Schematic Notes All components marked by this symbol have special safety characteris
4、tics, when replacing any of these components use only manufacturers specified parts. The (?) micro symbol of capacitance value is substituted by U. The () omega symbol of resistance value is substituted by E. The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified. All resisto
5、rs are 1/4W unless otherwise specified. All switches shown in the OFF position. All DC voltages measured to ground with a voltmeter 20KOhm/V. RPT114 RPT114/O BACHMANN RPT114 Opening Instructions Autotest Chart Blocks Diagram Power Amplifier & Supply Board, Phones & MIDI I/O Board Keyboard Interface
6、Board, Contacts Board CPU & Sound Generator Board RPT114/O (Optical Sensor Version with) Blocks Diagram Keyboard Interface Board, Optical Contacts Board (Left Part) Optical Contacts Board (Central & Right Part) Spare Parts List 5 6 7 4 8 9 10 3 4 2 o 2 124 3231 56 7 8 9 10 11 12 13 14 15 16 17 18 19
7、 20 21 22 23 24 25 26 27 28 2930 3 Assembled Parts (RPT114 version) 1) Key front19) Hammer Load 2) Key top20) Hammer stop rail 3) Natural, white key21) Hammer sto rail felt 4) Sharp, black key22) Hammer center pin 5) Balance rail pin23) Hammer but spring 6) Bridle wire, tape wire24) Hammer flange 7)
8、 Jack spring25) Spoon 8) Regulating button26) Wippen flange 9) Back check wire27) Jack 10) Regulting rail felt28) Jack flange 11) Regulating rail29) Balance rail pin 12) Bridle strap, bridle tape30) Front rail punching, front washer 13) Back check31) Front rail pin 14) Back check felt32) Contacts Ru
9、bber Strip 15) Butt heel leather, back stop leather 16) Butt heel, catcher, back stop 17) Hammer rest rail 18) Hammer rest felt, hammer rest baize 1) To remove the rear panel unscrew the twenty screws from behind of the instrument, pull the cover upwards and lift it up 2) To access the electronics p
10、arts turn the front panel locks and pull the panel towards you, to remove the control panel unscrew the four screws from the bottom side. 3) To access the speacker box you musts unscrew and pull the speakers front panel towards you. RadioFans.CN 收音机爱 好者资料库 3 o A B C C C C C 124 33 323134 56 7 8 9 10
11、 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3 Assembled Parts (RPT114/O version) 1) Key front19) Hammer Load 2) Key top20) Hammer stop rail 3) Natural, white key21) Hammer sto rail felt 4) Sharp, black key22) Hammer center pin 5) Balance rail pin23) Hammer but spring 6) Bridle wire,
12、 tape wire24) Hammer flange 7) Jack spring25) Spoon 8) Regulating button26) Wippen flange 9) Back check wire27) Jack 10) Regulting rail felt28) Jack flange 11) Regulating rail29) Balance rail pin 12) Bridle strap, bridle tape30) Front rail punching, front washer 13) Back check31) Front rail pin 14)
13、Back check felt32) Contacts Rubber Strip 15) Butt heel leather, back stop leather 16) Butt heel, catcher, back stop 17) Hammer rest rail 18) Hammer rest felt, hammer rest baize To access to the optical sensors remove all sharp and natural keys, we recommend to dispose the keys in order. Optical sens
14、ors BA Once removed the keys unscrew the five screws (B) from the front panel of the contacts board and unscrew the fourty- eight nuts (A) from the bottom. Optical Keyboard RPT114 AUTOTEST CHART PROCEDUREOPERATIONEVENT DESCRIPTIONS Loop the MIDI OUT with the MIDI IN Start sockets with a single MIDI
15、cable. Apply the volume control to the center position Turn on the instrument and press four timesThree different tones must be sound. the + key within one second. Active the following controls:At every action the instrument must play a beep. + key - key DAMPER Pedal SOFT PedalWhen all the buttons h
16、ave been actived at least once time, three different tones volume potentiometer.must be sound, to mean a successful test end. ControlsNote: The test must be performed within 20 seconds from the start, if this doesnt happen a sequence of beep are emitted, that meaning: 1st tones+ key doesnt work or h
17、asnt been activated 2nd tones- key doesnt work or hasnt been activated 3th tonesMIDI loop is not present or a MIDI socket dont work properly 4th tonesDAMPER pedal doesnt work or hasnt been activated. 5th tonesSOFT pedal doesnt work or hasnt been activated. 6th tonesVolume potentiometer doesnt work o
18、r hasnt been activated. The autotest operations can be performed only in the sequence specified above. NoteAll acousticals signals levels are fixed by the volume potentiometer position when the instrument is turned on. During test all normal keyboard function are disabled. To get the right dynamic r
19、esponse is very important to get perfect calibration of the keyboard. Keyboard calibrations. 1)Level Keys: Using standard circular paper spacers (contents in the calibration kit (970320), in position A to level: all 88 keys. The difference between all keys must be less than 0,1mm in point B. 2)Level
20、 Strip: Turn the six screws C to reach the right distance between the keys and rubber printing circuit board that is 4,2mm0,1 in one side and 8,7mm0,1from other side, as following showed. RPT114/O version keyboard sensors calibration ATTENTION The following operations serves to callibrate the keyboa
21、rd sensors. If this is not required, turn off the instrument at this point, otherwise continue as described below. Turn on the instrument and press four timesThree different tones must be sound. the - key w ithin one second. Optical sensors Press all sharp and natural keys one a time w ith the descr
22、ipted precautions: Play the keys w ith ppp (pianissimo) action. Release the keys slow ly to avoid any oscillation. auto- calibration Be sure that the keys is fully pressed untill the end stroke, but dont apply any extra pressure. Perform previous operations as uniform as possible for all keys. Durin
23、g calibration avoid any vibration to the keyboard. Wait for a few seconds w hile the instrument momorises permanentely the new ly calibration of the keyboard. Could happen that keys arent calibrated because: 1) optical sensors are dirty (look at the previous page how to access), Calibrations2) optic
24、al sensors arent in the right tollerance range, and Check3) keys and pedals arent calibrated in the right w ay. If at least one of previous three events come true, you can hear a sequence of tones (having a gap of 0.5sec). The heard tone belongs to the key not w ell calibrated. 2 tone - The upper th
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- General_Music_RPT114_Bachman_Service_Manual 电路图
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


