Neve 33609jd_technical_handbook_issue1电路图.pdf

《Neve 33609jd_technical_handbook_issue1电路图.pdf》由会员分享，可在线阅读，更多相关《Neve 33609jd_technical_handbook_issue1电路图.pdf（25页珍藏版）》请在收音机爱好者资料库上搜索。

1、 2003 AMS Neve plc own the copyright of all information and drawings contained in this manual which are not to be copied or reproduced by any means or disclosed in part or whole to any third party without written permission. As part of our policy of continual product improvement, we reserve the righ

2、t to alter specifications without notice but with due regard to all current legislation. Disclaimer: The information in this manual has been carefully checked and is believed to be accurate at the time of publication. However, no responsibility is taken by us for inaccuracies, errors or omissions no

3、r any liability assumed for any loss or damage resulting either directly or indirectly from use of the information contained within it. AMS NEVE INC., NEW YORK TEL: +1 (212) 965 1400 FAX: +1 (212) 965 9306 AMS NEVE INC., HOLLYWOOD TEL: +1 (818) 753 8789 FAX: +1 (818) 623 4839 AMS NEVE PLC BILLINGTON

4、 ROAD BURNLEY LANCS BB11 5UB ENGLAND TELEPHONE: +44 (0) 1282 457011 FAX: +44 (0) 1282 417282 H E A D O F F I C E TELEPHONE: +44 (0) 20 7916 2828 FAX: +44 (0) 20 7916 2827 LO N D O N O F F I C E N O R T H A M E R I C A N O F F I C E S e-mail: enquiryams- http:/www.ams- Technical Handbook 527-148 Issu

5、e 1 33609/JD Limiter/Compressor RadioFans.CN 收音机爱 好者资料库 Limiter/Compressor Technical HandbookPage 1 1. Limiter/Compressor Unit Introduction The limiter/compressor unit contains two identical, isolated channels which are suitable for mono, stereo or independent operation; units can be linked for mult

6、i-channel use. When limiting and compression is not required, both channels may be by-passed. Both mono, stereo and by-pass functions are switched by logic-controlled relays. Depending on the position of an EXTernal INTernal switch, these functions are either operated by front panel switches or exte

7、rnally controlled by a rear panel connector. The above switches are internally illuminated from the Logic to show the operational mode of the unit, and external tallies are available via the rear panel connector. The reset position of the relays is BY-PASS and MONO: when power is disconnected or swi

8、tched off, the unit is in BY-PASS mode. The limiter/compressor unit contains the following four identifiable sections: Limiter/Compressor board (11475): This is a motherboard which contains the attenuator control element, the 10340-C amplifier and the limiting and compression sidechain electronics.

9、The external control potentiometers, switches and gain reduction meters (which indicate the overall gain reduction in each channel during limiting and compression) are mounted on the front panel. Input and output sockets mounted on the rear panel. A D.C power and relay logic board, which provides a

10、regulated +24V supply for the 11475 board, and +5V for logic circuits controlling the relay switching. Limiter/Compressor Board (11475) This board contains the main audio signal processing circuits of the limiter/compressor unit. The operation of the board is described elsewhere. Front Panel Switche

11、s The rotary control switches located on the front panel of the unit are multi-contact multi-layer rotary switches. Electrical loading of the switches is provided via resistors connected across the contacts. RadioFans.CN 收音机爱 好者资料库 Limiter/Compressor Technical HandbookPage 2 Mains Power Supply The 2

12、4V DC input, derived from the main supply, required by the limiter/compressor board (11475) is supplied by a power supply unit located in the limiter/compressor unit. The power supply unit comprises a toroidal mains input transformer (TF14201), a regulator circuit (part of 11720), and associated com

13、ponents. The arrangement is shown as part of the limiter/compressor block diagram EB20515. Mains power is applied via an IEC inlet connector to the front panel mounted switch POWER. The switch illuminates when the unit is switched on. Input voltages of 100V, 120V, 220V or 240V AC can be selected usi

14、ng the voltage selector mounted on the rear panel. Primary circuit protection is provided by a 500mA anti-surge fuse for 100V, 120V, 220V or 240V operation, the fuse is located in the body of the voltage selector. The 24V AC output of the toroidal transformer is connected to the secondary protection

15、 fuse, a 500mA anti-surge type, mounted on the rear panel of the unit. Specification Frequency Response20Hz to 20kHz +/-0.5dB, measured at 0dBu relative to 1kHz. Noise-75dBu with input terminated in 600 ohms, by-passed IN, compress and limit OFF; -55dBu with compress IN and gain make-up at maximum.

16、Limit Level+4dBu to +15dBu, measured with limit recovery set at 50ms, level at +8dBu using a 1kHz sine-wave at +20dBu and +8 control adjusted to give +8dBu output. Limit Ratiowith input level at 10dBu, increased to +20dBu the change in output level should be 0.1dB, +/-0.1dB. Attack Timeslow: 4ms, +/

17、-1ms fast: 2ms, +/-1ms being the time taken for a signal to return to within 1dB of its original value, using an increase in input level of 10dB on an input adjusted to +10dBu at 1kHz. Limit Recoverythis is the time taken by the control voltage to reach a new value when an input at +20dBu is reduced

18、 in value by 10dB. The recovery times can be set to 50ms, 100ms, 200ms, 800ms, AUTO 1 1500ms, AUTO 2 3000ms (all +/-50%). Gain Make-upsettings 0 to 20dB correspond with output level +/-0.5dB. RadioFans.CN 收音机爱 好者资料库 Limiter/Compressor Technical HandbookPage 3 Compress Ratiorecovery set to 100ms thre

19、shold to -20dBu input 1kHz at 0dBu for each setting of the Compress Ratio Switch the input level is increased by 10dB and the change in output level should be: Compress Ratio Switch O/P Level Change (dBu) Tolerance (dB) 1.5 : 16.5 1 2 : 15.0 1 3 : 13.5 1 4 : 12.5 0.5 5 : 11.5 0.5 Compress Recovery10

20、0ms, 400ms, 800ms, 1500ms AUTO 1 800msAUTO 2 1500ms Distortion0.075% maximum (bypass IN, Compress and Limit OUT, input level at +9dBu, 1KHz). 0.2% maximum (Compress IN ratio 6:1, Gain make-up to MAX, Recovery 800ms, Threshold 18dBu). 0.45% maximum (Limit IN, Compress OUT, Recovery 800ms. Input level

21、 +22dBu, Threshold 18dBu). Power Consumption5.3VA DimensionsLength:482mm (19in) Height:88mm (3.26in) Depth:255mm (10.03in) Limiter/Compressor Technical HandbookPage 4 2. Switch Assembly Information Assembly information for the following switches is included in this section: Switch Function Compress

22、RatioPL20233 Gain Make-UpPL20234 Compress ThresholdPL20235 Compress RecoveryPL20236 Limit RecoveryPL20237 Limit levelPL20238 Limiter/Compressor Technical HandbookPage 5 3. Limiter/Compressor Board (11475) The main audio path through each channel is via T2, D14, to D17, TR16 and TR17, TR3 and TR4, T1

23、, T3 and the bypass switch. The remaining components on the board and some external components from the sidechain. The incoming audio signal is applied to the transformer T2 which feeds a balanced attenuator pad formed by R47 to R49 and R11. The active attenuator of the limiter/compressor is formed

24、by a balanced diode bridge D14 to D17. A DC Control voltage, derived b the limiter or compressor sidechain sections, is used to forward bias the diodes in the bridge and thereby alter the effective value of the attenuator resistance. The attenuator pad reduces the input signal level such that the si

25、gnal remains in a linear region of the diode characteristic. A high impedance buffer is formed by transistors TR16, TR3, TR17 and TR4, eliminating loading effects by the transformer T1 on the diode bridge. The signal from T2 is fed to the power amplifier 10340-C via the gain preset control RV1. From

26、 the power amplifier the signal is supplied to the output transformer T3 and then via connector pins P3 10 and P3 9 to the output bypass/in switch. Transistors TR2, TR5, TR8 and TR9 form the active components of the compressor sidechain and TR6, TR7 and TR10 to TR13 the active components of the limi

27、ter sidechain. The combination of TR9, TR13 and TR1 gives a low output impedance signal equal to the larger of the compressor or limiter sidechain signals. The voltage is attenuated by R36, RV2, R45, R29 and D10 supplied as the control voltage to the diode bridge. Limiting The output of the power am

28、plifier board (10340-C) is connected via the limit in (Plug 3, pin 1; P3 1), the threshold dBu control (RV4) (P1 4 and P1 5) and capacitor C11 to a phase dividing amplifier pair TR6 and TR10, the outputs of which are rectified by diodes D7 and D8. Transistors TR11 and TR7 form a threshold detector a

29、nd DC amplifier to feed TR12 via D9. The threshold reference is derived by D13 and R22. Emitter follower TR12 charges a storage capacitor C14 through R28 which determines the attack time constant of the limiter. R30 is connected in parallel with R28 when the attack switch is in the fast position. Th

30、e recovery time is set by the resistance of the recovery ms control (P2 1 and P1 7/8). P1 7/8 is connected to the junction of D11 and R8. D11 provides a temperature compensated reference voltage for use in the recovery time circuits of the limiter/compressor sidechains. Transistors TR13 and TR1 form

31、 a high input impedance buffer stage following the time constant circuit. To set the exact limit threshold of the sidechain circuit, the threshold control is set to the +8dBu position and an input level of +20dBu is applied to the module. The preset potentiometer RV4 is adjusted (altering the gain o

32、f the amplifier stages TR6 and TR10) to obtain an output level of +8dBu. Limiter/Compressor Technical HandbookPage 6 Compression The input signal to the compressor sidechain is taken from the wiper of RV1 and is connected via the compress in switch and C12 to the base of TR2. The gain of the amplifi

33、er formed by TR2 and TR15 is changed by the value of resistance selected on the threshold dBu control. TR5 is used as the threshold detector, taking its reference from D2 and R50, and provides current drive to the series network of D12, D3 to D6 and R26 and the compress ratio control. These componen

34、ts give a voltage of the correct characteristic necessary for the selected compression ratio. This voltage turns on TR8 which charges C13 via R31. The time constant determined by the combination of R31 and C13 sets the fixed attack time constant of the compressor. The resistance selected by the comp

35、ress recovery (ms) control and the value of C13 determines the recovery time constant of the circuit. The voltage on C13 is fed to the high impedance buffer formed by TR9 and Tr1. The emitter load of TR9 is formed by R36, RV2, R45, R29 and D10 and produces a law correction characteristic necessary t

36、o properly drive the gain control diode bridge. The voltage on the emitters of TR9 and TR13 is connected to the meter preset RV3 and to the gain reduction meter itself via D18 and R35. The wiper of RV3 is buffered by emitter follower TR14 and the output signal fed to the gain reduction meter via R32

37、. Rv3 is adjust to calibrate the meter at known levels of gain reduction., D18 and R35 feed a small amount of the control voltage directly to the meter to improve the accuracy at small amounts of gain reduction. Gain Make-Up If a compressor threshold point below line level is selected, it may be nec

38、essary to add gain after compression to restore mean programme level. The function is obtained by use of the gain make-up control which alters the feedback in amplifier 10340-C when the compress in switch is closed. BA340-C or Limiter/Compressor Technical HandbookPage 7 4. Power Amplifier (10340-C)

39、Introduction This board is a large pin version of the 10340 and is a line amplifier with a low impedance output, suitable for use as a distribution amplifier. It is designated as a plug-in unit to be incorporated in a larger motherboard. The gain of the circuit is determined by the value of an exter

40、nal gain boost resistor. Circuit Description The circuit is driven by a nominal +24V supply; decoupling and smoothing components will normally be mounted on the motherboard. Inverting a non-inverting inputs are both accessible on L2 a gain boost resistor can be fitted between the PCB inverting input

41、 (pin 2) and 0V. Specification Quiescent Conditions:With a gain boost resistor of 1k6 ohm (equivalent to +20dB gain) and the output terminated in 620 ohm, the static current should be approx 22mA; the standing output voltage (pin 6) should be +12V 1V. Gain:With 1kHz sine wave input at 10dBu, the out

42、put level should be +10dBu 0.5dB. Maximum Output:With an output load of 75 ohm and the 1kHz input level increased until the output signal is just clipping, the output level should be greater than +18dBu. Distortion:At 1kHz input adjusted to give 18dB output into 75 ohm, the distortion should be as f

43、ollows: 20Hzno more than 0.02% 1kHzno more than 0.01% 15kHzno more than 0.05% NoiseWith the input short-circuited, the output noise level must be less than 95dBu over the bandwidth 20Hz to 20kHz. Limiter/Compressor Technical HandbookPage 8 5. Limiter/Compressor DC Power & Relay Logic Board (11720) T

44、he PL11720 board contains power supply and audio switching circuitry for the PL33609/J limiter/compressor. The power supply is based around regulator IC6. The AC supply from the mains transformer is applied via CONN 5 Pins 1 and 2, rectified and smoothed by D7 and C6 respectively. IC6 regulates the

45、smoothed DC voltage down to +24V factory preset by RV1. Audio In/Out switching is accomplished by four pole relays RL 1 and 2. (Left and Right channels respectively) Stereo Linking of Left and Right control voltages is accomplished by RL3. Control of the three relays is achieved by IC1, 2 and 3. The

46、 logic controlling In/Out and Stereo Linking is similar, and this description will only describe In/Out switching. Analogue switch (output pin 14) IC2, selects between control from the front panel switches or from an external control via the 15 Way “D” connector. A logic level from the front panel I

47、NT/EXT switch determines which input of IC2 is selected: Logic 0 (0V) pin 12 - Internal Logic 1 (5V) pin 13 External The external input I s clamped by D2 and buffered by IC1 (output pin 3) before being applied to IC2. The output of IC2 is de-bounced by IC1 (output pin 8) and R6, D3 and C3 and then a

48、pplied to the clock input of “D” type latch IC3 (outputs pins 5 and 6). The output of IC3 is fed to TR1 which drives the coil of RL1 and 2. TR2 similarly drives the By-pass illumination of the front panel switch. IC4 (output pin 1) is a comparator which monitors the pre-regulator DC voltage. In the

49、event of this voltage falling below a preset level the output switches low “stealing” the base current of TR1 and thus de-energising the relays hence switching the unit into “By-pass” mode. This ensures continuity in the event of a power failure. R7, D4 and C2 clear the latches on power-up. Regulator IC5 regulates the 24V supply to +5V for the logic ICs. threshold dBu recovery ms LIMIT 1 Limit In slow attack fast threshold dBu recovery ms LIMIT 2 Limit In slow attack fast threshold dBu recovery msgain ratio threshold dBu recovery msgain ratio compress