Roland VS-1680 Digital Studio Service Manual 电路图.pdf

《Roland VS-1680 Digital Studio Service Manual 电路图.pdf》由会员分享，可在线阅读，更多相关《Roland VS-1680 Digital Studio Service Manual 电路图.pdf（29页珍藏版）》请在收音机爱好者资料库上搜索。

1、Sep, 1998VS-1680 TABLE OF CONTENTSPage SPECIFICATIONS 12 LOCATION OF CONTROLS 3 EXPLODED VIEW4 BLOCK DIAGRAM 5 PARTS LIST67 IDENTIFYING VERSION NUMBER 710 TEST MODE710 SETTING THE INTERNAL CLOCK 10 VS-840 SYSTEM SOFTWARE UPDATE USING THE SMF 10 SAVING DATA OF INTERNAL HDD1113 EXCHANGE THE MAIN BOARD

2、 14 CIRCUIT DIAGRAM MIDI OUT connector of the MIDI Sequencer that can play back SMF data and MIDI IN connector of VS-1680. It is convenient to use the MIDI Sequencer such as an SB-55 sound brush that can play back some SMFs continuously. 2. While holding down TRACK SELECT and STATUS on the CH7, turn

3、 on the VS-1680s power. 3. A message SYSTEM Update? will be displayed. Press YES. 4. Check a message Waiting MIDI-EX is displayed, play back all SMF data from VS-168001. MID to VS-168016. MID in order. 5. After finish playing back all SMFs, a message Update SysPRG? will be displayed. Press YES. 6. A

4、 message Please Reboot OK will be displayed. The system software of your VS-1680 was already updated. Restart the VS-1680. To update the VS-1680 using the disk, follow the procedure described below. Note that if the version of the disk is identical to that of the VS- 1680, no updating is possible. R

5、ather, the unit simply operates in the play conditions. 1. Connect a zip drive to VS-1680 through the SCSI cable. Turn on Zip drive. 2. Insert the disk into the zip drive. 3. Turn on VS-1680. 4. The message System Prog Load Now working . appears indicating the start of updating. 5. Fig.1 is displaye

6、d. When the updated data is correct, press YES button. SETTING THE INTERNAL CLOCK VS-1680 SYSTEM SOFTWARE UPDATE USING THE SMF SYSTEM SOFTWARE UPDATE USING ZIP DISK Sep, 1998VS-1680 - Updete System Program ? - Ver.1.xxx ( Btver1.00 ) YES / NO Fig.1 - Keep User Setting ? - EZ ROUTING User Routing EFF

7、ECT User Patch ARARM User Data NO is Init User Seeting YES / NO - Init User Setting Sure ? - EZ ROUTING User Routing EFFECT User Patch ARARM User Data YES / NO Fig.2Fig.3 11 6. Fig.2 is displayed. If the user date is required to be saved,press YES button. If NO button is pressed, Fig.3 is displayed.

8、 If it is OK, press YES button. 7. The message Now Working .* appears indicating the start of count down. When the message Please Reboot OK appears and LEDs on the VS-1860 are flashing, the updating procedure is completed. Turn off VS-1680. 8. Remove the zip disk and turn off the zip drive. Remove t

9、he SISI cable. If it is necessary to replace a PCB on the user VS-1680, save the user system parameters and Effect user patches onto a sequencer or equivalent storage. Load back the data onto the VS-1680 after it has been fixed. ISend the parameters through MIDI OUT 1. Pressing CH7 TRACK SELECT and

10、STATUS and F5 SYSTEM button simultaneously, turn on POWER switch on VS-1680. 2. The message Send SysPrmMIDI? is displayed. Press YES button and the system parameters are sent in MIDI exclusive format. IRestore the system parameters To receive the system parameters D-sub type, pin25 (female). To conn

11、ect the cable correctly, please confirm the form of the SCSI connector of the disk drive to be connected. GKeep SCSI cable as short as possible, and use only cables which have an impedance (110 ohms +/- 10%) that is compatible with the SCSI standard, and are completely shield. GDo not allow the tota

12、l length of all SCSI cables connecting the chain of disk drives to exceed 6.5 meters. GDo not connect or disconnect SCSI cables when the power of any device is turned on. Turning power on. 1. Turn on the power to the Zip drive. 2. Turn on the power to the VS-1680 with the POWER switch on the rear pa

13、nel. A new disk just purchased at your computer store or a disk that was used by another device cannot be used on the VS-1680 as is. You must initialize the disk by VS-1680 so that it can be used by the VS-1680. When a disk is initialized, the entire contents are irretrievably lost. Check any such d

14、isk you plan to initialize to make sure that it does not contain anything that you dont want deleted. If you are using a drive or disk that has been partitioned, please note that you will not be able to choose a particular partition that you wish to initialize. When you carry out a drive initializat

15、ion, the whole drive and all its partitions will be initialized at once. IInitializing new Zip disks. 1. Confirm that power to the Zip drive and the VS-1680 is turned on. 2. Insert a disk into the Zip drive. 3. Press PLAY (DISPLAY) 4. Hold down SHIFT and press F6 (UTILITY). The Utility menu icon app

16、ears in the display. 5. Press F6 (DrIni). If DrIni does not appear in F6, first press PAGE until DrIni is displayed, then press F6 (DrIni). 6. Use , v, to move the cursor. Rotate the TIME/VALUE dial to make each of the values settings. IInit Drive (Initialize Drive): Select the disk drive (IDE, SCSI

17、0SCSI7). IDE indicators internal hard disks, and SCSI0SCSI7 (these are SCSI ID numbers) indicate external hard disks. For example, select SCSI5 when selecting the Zip drive connection. IPartition: Select the partition size (500 MB, 1000 MB, or 2000 MB). In normal circumstances, select 2000 MB. IPhys

18、ical Format: Select whether or not to use physical formatting. For new disks or disks that have been used by another device, select On. For new hard disks or when formatting disks for Windows or Macintosh platforms, select Off. ISurface Scan: This confirms that the read and write functions in all of

19、 the disk drives partitions are operating correctly when the drive is initialized. In normal circumstances, set this to Off. When you particularly want to conduct a test of the read/write functions, the set this to On. At this time, the function buttons work as shown below. F1 (DrSel): This displays

20、 a directory of the currently connected drives. Use , v, to select the drive that you want to initialize. F3 (Info):Displays the drive information. F4 (Exec):Executes initialization of the selected drive. F6 (EXIT):Exits the screen. 7.When the settings are made, press F4 (Exec). Init. *, OK? appears

21、 in the display. * refers to the drives SCSI ID number. For example, SCSI5 indicates a Zip drive. 8.Press YES. Init *, Sure? (Really initialize the disk?) appears in the display. 9.Press YES. STORE Current? (Store the current song?) appears in the display. SAVING AND LOADING DATA OF INTERNAL HDD VS-

22、1680 Sep, 1998 SAVING SYTEM PARAMETERS SCSI cableSCSI cable VS-1680 Zip drive INITIALIZING THE DISK (DRIVE LNITIALIZE) 12 10. If you wish to save the current song, press YES; if not, then press NO. If you have selected a demo song, then press NO. 11. After the initialization is completed correctly,

23、the VS-1680 restarts automatically, and you are returned to Play condition. * Be aware that initializing a drive requires some time. This is not a malfunction. For example, when physical formatting is turned on, the time required to format one Zip disk is approximately 10 minutes. The progress of in

24、itialization will be shown in the display. Be sure not to turn the power off until initialization is complete. There are two ways to carry out the Song Copy procedure. Select the method you will use based on the amount of free space on the destination disk (100 MB for Zip disks). The amount of memor

25、y used on the disk is shown in the display. Playable:Use this method to copy songs that use relatively little data onto disks with sufficient memory to hold them. If the destination drive or disk already has song data saved on it, then you can copy additional songs that will fit within the remaining

26、 free space. Archive:Use this method to copy songs that are too large to be saved on a single disk. The song data is converted into a data format specifically for saving (archive format), and is copied onto multiple disks according to the free space on the disks. This means that it will not be possi

27、ble to directly play back the song data. If you wish to play back song data copied in archive format, you will need to reload the archive data into the current drive using the appropriate procedure. Furthermore, song data cannot be copied onto disks that already have songs recorded on them. ISaving

28、a Song to a Single Disk (Playable) Save a playable copy of a song on the VS-1680s internal hard disk to a Zip drive which is set to SCSI ID Number 5. 1.Select the disk containing the source song you want to copy as the current drive. 2.Press PLAY(DISPLAY) 3.Hold down SHIFT and press F1 (SONG) The So

29、ng menu icon appears in the display. 4.Press F1 (CP PL). If CP PL does not appear in F1, first press PAGE until CP PL is displayed, then press F1 (CP PL). 5.Press to move the cursor to Source Song. 6.Use the TIME/VALUE dial to move the cursor to the song you want to copy and press F3 (MARK). By pres

30、sing F2 (ALL), you can place and remove Markers from all of the songs. In addition, you can press F1 (SelSg) to display a directory of the songs. At this point, after you have placed a Marker at the song you want, press F1 (Back). 7.Press to move the cursor to Destination Drive. 8.Use the TIME/VALUE

31、 dial to select the destination drive and partition. You can press F5 (SelDr) to display a directory of drives. At this point, use , v, to select the destination drive, and select the destination partition with the TIME/VALUE dial. Once you have selected the destination drive, press F1 (Back). 9.If

32、the source and destination drives are different, press v. Move the cursor to Erase All Songs with the TIME/VALUE dial. * Erase All Songs When this is set to On, the copy procedure is carried out after the destination drive is initialized. If you want to perform the copy procedure leaving songs alrea

33、dy saved in the destination drive as they are, then set this to Off. 10. Press F4 (Exec). A message asking if you want to continue appears in the display. 11. Press YES. STORE Current? (Store the current song?) appears in the display. 12. If you wish to save the current song, press YES; if not, then

34、 press NO. If you have selected a demo song, then press NO. 13. When copy is completed, the Song menu icon appears in the display. Press PLAY (DISPLAY). Return to Play condition. NOTE: If Disk Memory Full Appears in the Display This indicates that the destination disk has insufficient free space, or

35、 that the number of songs on the disk has exceeded the maximum number (200 songs) that can be stored on the disk, and that the copy procedure was canceled. However, you can still use the song data copied up to that point. ITo Load Data from Disks Use the following procedure to take playable songs th

36、at have been copied to Zip disks and load them onto the VS-1680s hard disk. Switch the current drive to Zip drive (Drive Select). Then perform playable copy from Zip drive to the internal hard disk drive. * The original song is not overwritten by performing these procedures if the original song that

37、 copied from the internal hard disk to Zip disk is not erased from the internal hard disk. In that case, a new song which has the same name as the original one will be create in an available earliest song number. 1.Confirm both power of Zip drive and VS-1680 are turned on. 2.Insert the disk containi

38、ng the song you want to load into the Zip drive. 3.Press PLAY (DISPLAY). 4.While pressing SHIFT press F6 (UTILITY). The utility menu icon is appeared on the display. 5.Press F4 (DrSel). If DrSel does not appear on F4, first press PAGE to show DrSel then press F4 (DrSel). Table of the current connect

39、ed drive will be shown on the display. 6.To move cursor, press , v, . Select the drive you wish to switch. To select the partition which you wish to switch, rotate the TIME/VALUE dial. At this time, the function buttons works as described below. F3 (Info): Indicate the drive information. F4 (Exec):

40、Execute drive select. F6 (EXIT): Exit from the menu. 7.After select drive/partition press F4 (Exec). 8.A confirming message is appeared on the display. Press YES. 9.STORE Current? (Save the current song?) message is appeared on the display. If you wish to save the current song press YES, if not pres

41、s NO. When the demo song is selected press NO. 10. When the current drive is switched song menu icon is displayed. Press PLAY (DISPLAY). Return to play condition. 11. Make a playable copy of the song from the Zip disk onto the VS-1680s hard disk, as described in Saving a Song to a Single Disk. Sep,

42、1998VS-1680 SAVING PERFORMANCE DATA TO A ZIP DRIVE (Song Copy) 13 12. When playable copy is completed, repeat the procedures 3 to 10 and select the internal hard disk as a current drive. IWhen You Cannot Save a Song to a Single Disk Handling of Archive Copy Disks To save songs in archive format, the

43、 destination disk must be initialized. This initialization procedure differs from the usual Drive Initialize formatting. This procedure lets you carry out Archive Copy with newly purchased disks, disks which previously have been used with a personal computer or other device, or other disks which hav

44、e not been formatted with Drive Initialize. However, any song data saved to the disk is lost once the Archive Copy procedure is performed. Additionally, you cannot designate a disk containing archive format songs as the current drive. If you try to do this, the disk is identified as being an uniniti

45、alized disk. ISaving to Disks (Store) 1.Make the drive containing the song you want to load the current drive. 2.Press PLAY (DISPLAY) 3.Hold down SHIFT and press F1 (SONG). The Song menu icon appears in the display. 4.Press F2 (AC Str). If AC Str does not appear in F2, first press PAGE until AC Str

46、is displayed, then press F2 (AC Str). 5.Press to move the cursor to Destination Drive. 8.Use the TIME/VALUE dial to select the destination drive and partition. Press F5 (SelDr) to display a directory of drives. At this point, use , v, to select the destination drive, and press F1 (Back). 9.Press F4

47、(Exec). A message asking if you want to continue appears in the display. 10. Press YES. STORE Current? (Store the current song?) appears in the display. 11. If you wish to save the current song, press YES; if not, then press NO. If you have selected a demo song, then press NO. * All data saved on th

48、e Zip disk will be deleted. Do not use any Zip disk containing song data that you need. 12. If the song holds a large amount of data, and cannot be contained on a single Zip disk, the disk is ejected, and the message Please Insert Disk appears in the display. Insert the next disk and press YES. At t

49、his time, be sure to write the disk numbers on the labels so that you can keep track of the order in which the disks were inserted into the drive. 13. When copying over multiple Zip disks, Insert Disk # (# indicates the number in the order of insertion) appears in the display. Insert each of the disks once more in the proper order and press YES. 14. When the Archive Store procedure is finished, the Song menu icon appears in the display. Press PLAY (DISPLAY). Return to Play condition. ILoading Data