Rolls HM60 Headphone Monitor Manual & Schematic 电路图.pdf

《Rolls HM60 Headphone Monitor Manual & Schematic 电路图.pdf》由会员分享，可在线阅读，更多相关《Rolls HM60 Headphone Monitor Manual & Schematic 电路图.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、HM60 Headphone Monitor System OWNERS MANUAL ROLLS CORPORATION SALT LAKE CITY, UTAH 3/00 LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the

2、date of purchase as shown on the purchasers receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service,

3、 provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE- PAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date

4、 of manufacture. This warranty shall be invalid if the product is damaged as a result of deface- ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our o

5、wn service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTI

6、ES OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIAB

7、LE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This war

8、ranty gives you specific legal rights, and you may also have other rights which vary from state to state. PWR 64 125 250 500 1K2K4K8K 16K EQUALIZER MASTER LEVEL PHONE/ LEFTRIGHT AGC COMP EFFECTS RETURN HEADPHONE MONITOR SYSTEM 0 +12 -12 MIX LEVELS MAIN1234 MIX OUTPUT EFFECTS SENDS 1234 EFFECTS SEND

9、STEREO INPUTS EFFECTS RETURN EXPANSION120 VAC 50/60Hz MONO INPUTS RL/MONR/MONL/ST HM60 RadioFans.CN 收音机爱 好者资料库 INTRODUCTION Thank you for your purchase of the Rolls HM60 Headphone Monitor System. This unit allows you to mix four mono signals with two stereo signals for your own personal monitoring n

10、eeds. It includes equalization and AGC compression. When coupled with an HM59 or HM58 Headphone Monitor Remote units, the custom mixing can be controlled in separate locations. Please read the following manual carefully to get the best results from your HM60. TABLE OF CONTENTS Introduction1 Table of

11、 Contents1 Inspection1 Specifications1 Description Top Panel2 Front Panel2 Bottom Panel2 Connection3 Operation4 Block Diagram5 Schematic6 WarrantyRear Cover INSPECTION 1. Unpack and inspect the HM60 box and package. If obvious physical damage is noticed, contact the carrier immediately to make a dam

12、age claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. 2. Please complete the Warranty Registration Card and return it to the factory. SPECIFICATIONS Output Impedance:10 Sensitivity:Variable, -10 to +4 dB for rated output Power Output:5

13、00 mW at 32 (150 mW at 600 ohms) 20 Hz to 20 KHz. Connectors:Inputs: Outputs: 1/4 TRS stereo headphone jack, DB25 jack Distortion:0.008% THD full power 1 KHz; 0.05% THD 20Hz to 20 KHz Dynamic Range:Greater than 96 dB Freq. Response:20 Hz to 20 KHz, +0, -1 dB 400 mW output Power Requirement:Rolls PS1

14、2 12VAC power supply Dimensions (HxWxD):6.3” x 10.25” x 1.625” Weight:3 lbs. 16 SCHEMATIC Sheet 1 ROLLS CORPORATION 5143 South Main Street Salt Lake City, UT 84107 15-Oct-1999 Title: ROLLS PERSONAL MONITOR SYS. HM60 Size: Date: Rev: of Rb ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

15、 ? ? ? VCC VCC VDD VDD VDD VDD VCC VCC VCC VDD ? ? ? ? ? ? ? ! ? ? ? ? ? ? ? ? ? ? 3 2 1 4 # ? ? ? $ ? ? 6 5 7 8 # ? % ? $ ? ? 2 3 1 4 # ? ? ? $ ? ? the four mono inputs, the main stereo inputs, the effects returns and the power. It connects to the Rolls HM58 or HM59 Headphone Monitor Remote units.

16、Consult their respective owners manuals for more information on connecting and operating them properly. 120VAC: Power cord - connect to a properly grounded ac outlet. FRONT PANEL EFFECTS SENDS: These controls adjust the level of signal sent from the corresponding input to the EFFECTS SEND jack. EFFE

17、CTS RETURN: Adjusts the level of stereo signal returning from a signal processor (or whatever is connected to the Effects Return jack(s). These inputs may also be used as an additional set of stereo inputs. MIX LEVELS: Controls 1 - 4 and Main; adjust the level of input signal from the corresponding

18、input. MASTER LEVEL: Adjusts the amount of mixed signal sent to the Mix Output jacks. EQUALIZER: These slider controls adjust the level of the indicated frequency. For example, the 64 slider boosts or cuts the 64 Hertz component of the output signal by + or - 12 dB. PWR: Indicates that the HM60 is c

19、onnected to a power source and is on. BOTTOM PANEL MIX OUTPUT: Phone/Left:For connection to a set of stereo headphones. If a mono Tip- Sleeve plug is connected, this jack becomes the Left Output. Right:Contains the Right portion of the Output signal. AGC COMP: This switch engages the Automatic Gain

20、Control compressor. BLOCK DIAGRAM Unbal FX Send L R L R 4 3 2 1 TRS Balanced Inputs TRS Balanced Main Inputs Unbal FX Returns MONO MIXES FX RETURN MAIN LEVEL EQUALIZER EQUALIZER 2:1 COMPRESSOR 2:1 COMPRESSOR Headphone OutputCOMRPESSOR IN/OUT FX SEND LEVELS MASTER OUTPUT LEVEL DB25 MULTI-PIN CONNECTO

21、R -V +V RadioFans.CN 收音机爱 好者资料库 CONNECTION Make sure the HM60 is connected to a properly grounded AC outlet. Before turning on the HM60 power switch, make all audio connections. Shown below is an example for connecting your HM60 to a mixer. PWR 64 125 250 500 1K2K4K8K 16K EQUALIZER MASTER LEVEL PHON

22、E/ LEFTRIGHT AGC COMP EFFECTS RETURN HEADPHONE MONITOR SYSTEM 0 +12 -12 MIX LEVELS MAIN1234 MIX OUTPUT EFFECTS SENDS 1234 FX SEND RL/MON STEREO INPUTS R/MONL/ST EFFECTS RETURN EXPANSION120 VAC 50/60Hz MONO INPUTS To HM58 or HM59 REMOTE UNITS AUXILIARY SENDS MAIN OUTPUTS SUB OUTPUTS MAIN MIXER Shown

23、below is an example for proper connection to a signal processor. PWR 64 125 250 500 1K2K4K8K 16K EQUALIZER MASTER LEVEL PHONE/ LEFTRIGHT AGC COMP EFFECTS RETURN HEADPHONE MONITOR SYSTEM 0 +12 -12 MIX LEVELS MAIN1234 MIX OUTPUT EFFECTS SENDS 1234 FX SEND RL/MON STEREO INPUTS R/MONL/ST EFFECTS RETURN

24、EXPANSION120 VAC 50/60Hz MONO INPUTS To HM58 or HM59 Reverb unit or other effects processor INOUT RIGHTOUT LEFT 34 OPERATION OPERATING THE HM60 The HM60 can be operated as a stand-alone monitor mixer and headphone amplifier, or as a distribution system. After proper connections are made, begin sendi

25、ng signals to the HM60. Set the Master Level control at approximately 12 Oclock. Carefully bring up the 1-4 and Main Mix Levels until a desired mix is achieved. Adjust the Equalizer as needed. The 64, 125, and 250 Hz sliders control the lower or bass frequencies, the 500, 1K, and 2K sliders adjust t

26、he middle frequen- cies, the the 4K, 8K, and 16K sliders vary the high or treble frequencies. The AGC compressor keeps transient signals like pops or feedback under control, so they wont damage your hearing. It also slightly brings up low-level signals. NOTE: Much of the signal content may not be co

27、mpressed, you may not notice any effect. Only very high level or low level signals are effected. To use external effects processors, connect the FX Send jack to the Input of your effects unit, connect the output(s) of the processor to the Effects Return jacks (See the connection example on Page 3).

28、If you are using a mono signal out of the processor, use the Right/Mono jack. The Effects Send controls 1 - 4 and Main adjust the amount of signal from the indicated input out the Effects Send jack and to your effects processor. Adjust the Output Level of your processor along with the HM60 Effects R

29、eturn control to set a desired amount of effect you want. OPERATING THE HM60 WITH THE HM59 OR HM58 HEADPHONE MONITOR REMOTES. Combining the HM60 with the HM59 or HM58 Headphone Monitor Remote units allows users to make and control their own monitor mix. After proper connection of the HM60 to the aud

30、io sources, connect the DB25 cable to the HM59 or HM58. From those units, more HM59 and HM58 units may be connected. NOTE: The Effects Sends, Mix Levels, Effects Return, Master Level, AGC Compressor, and Equalizer on the HM60 will have no effect on the signals sent out the DB25 cable to the HM59 or HM58. Refer to the HM58 or HM59 Owners Manual for their proper opera- tion.