studer Quick Start Guide Studer PlugIn Engine 电路图.pdf

《studer Quick Start Guide Studer PlugIn Engine 电路图.pdf》由会员分享，可在线阅读，更多相关《studer Quick Start Guide Studer PlugIn Engine 电路图.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、 28.5.2008 WP Quick Start Guide STUDER VST PlugIn Engine Page 1 of 6 Quick Start Guide STUDER VST PlugIn Engine 1. Mount the rack PC in the Vista 5 SR local rack flightcase, where indicated in the hookup diagram. Please make sure that the rear rack mounting ears are used to also mount the pc to the

2、rear side of the rack . 2. The following cable connections need to be done according to the hookup diagram : Mains connector of the PC (preferrably via UPS) Ethernet Cat5 cable from PC network port1 to the Vista desks Secondary Lan port One single MIDI cable from the Vista desks MIDI Out1 to the PCs

3、 RME cards MIDI In 1 One pair of optical fibre cable - multimode fibre with two SC connectors on each end - from the PCs RME MADI card to the Local Rack D21m frame second last MADI I/O card. 3. When these connections are in place, the Studer PlugIn Engine can be started Power On The logon then autom

4、atically comes up with user=Administrator ; log on with studer as password (you can of course later change the password for maximal security) Start the Forte-Ensemble Application by doubleclicking the icon The Preset STUDER Vista5 SR FOH template is automatically loaded or Add Inputs and Busses manu

5、ally Load the desired PlugIns Switch on the processing with the big red power button on the top right side of the application Note : The Preset “STUDER Vista5 SR FOH template” is write protected and cannot be overwritten. It is automatically loaded after starting the Forte application. It is to prev

6、ent events of instability when your session specific Plugin settings are loaded after the empty template is loaded. RadioFans.CN 收音机爱 好者资料库 20.5.2009 WP Quick Start Guide STUDER VST PlugIn Engine Page 2 of 6 4. Making the appropriate patch connections in the Vista : Basically, there are two ways of

7、using a VST PlugIn as an effect for the Mixing console. Send Effects via Aux Send Insert Effects in a single channel A Send Effect has the advantage that it can receive signals fed from several channels at the same time. Usually effects such as Reverb and Delay are used in such a way. The signals ar

8、e fed by Aux Send (mono or stereo) to an Aux bus where the contributed signals are summed together. In the Vista consoles such an Aux bus is normally followed by the Aux master channel, in order to have a fader which allows to determine the level of the mix fed to the PlugIn effect. An Insert Effect

9、 in a single channel is typically an effect which is either used to control the dynamics of the signal, or it is a very specific effect which is only used for one single channel. Since the Vista consoles are equipped with very sophisticated dynamics processing per channel, it is recommended that the

10、 mixing console internal dynamics are used not to the last because of additional latency which is introduced with VST PlugIns. Of course, insert effects can also be used in output channels e.g. a graphic EQ in a Master channel. There the latency issue is probably less problematic, since the whole mi

11、x would be delayed and not only a few input channels what could cause comb filtering under certain circumstances. Patching for Send Effects Open “General Patch” view. Connect DirOuts of Aux Masters to the MADI Outputs of the first free available MADI card (where the Plugin Engine is connected with a

12、 fibre to). Bring the Returns from the Plugin Engine via MADI card to Stereo Inputs that then are used to bring the Effect Returns into the mix. RadioFans.CN 收音机爱 好者资料库 20.5.2009 WP Quick Start Guide STUDER VST PlugIn Engine Page 3 of 6 Patching for Insert Effects Open “Channel Patch” view. Doublecl

13、ick in the “Snd” field of the appropriate channel This will lead you to the Insert Send position in the General Patch Make the patch connection from this channel to the MADI output which feeds the Plugin Engine Go back to the “Channel Patch” view Now doubleclick in the “Ret” field of the same channe

14、l RadioFans.CN 收音机爱 好者资料库 20.5.2009 WP Quick Start Guide STUDER VST PlugIn Engine Page 4 of 6 This will lead you to the Insert Ret position in the General Patch Make the patch connection from the MADI input from the Plugin Engine return to the Insert Return of the channel. Check for the correct labe

15、ls in the “Channel Patch” view 5. Tweak VST Plugin Setings per Song / Scene 6. Store settings 20.5.2009 WP Quick Start Guide STUDER VST PlugIn Engine Page 5 of 6 Name Settings and change the Order : 7. Add MIDI Program changes to the cues in the Vista CueList : 20.5.2009 WP Quick Start Guide STUDER

16、VST PlugIn Engine Page 6 of 6 Give a different Program number to every subsequent cue. In this example, the top cue would be Program change #1 and the lowest cue is Program change # 11. It is best when they are in sequential order with the cue number. 8. Enable Scene change via MIDI on Plugin Host S

17、W ? Now the Vista cues are linked with the VST Plugin cues, and when a cue is fired (cue list needs to be armed!) the corresponding cue on the Plugin Engine gets fired also. Doubleclick the Plugin Engine“ remote desktop icon Enter the IP adress of Plugin Engine : 192.168.2.200 Logon and Startup of the Studer VST Plugin Engine via Remote Desktop Connection (20.5.09 wp)1. Log on with administrator“ and password “studer“ 2.