Yamaha AW4416 Audio Workstation Service Manual 电路图.pdf

《Yamaha AW4416 Audio Workstation Service Manual 电路图.pdf》由会员分享，可在线阅读，更多相关《Yamaha AW4416 Audio Workstation Service Manual 电路图.pdf（156页珍藏版）》请在收音机爱好者资料库上搜索。

1、AW4416 1 SERVICE MANUAL PA 011525 20000825-OPEN PRICE 1.44K-6332 K Printed in Japan 00.09 HAMAMATSU, JAPAN CONTENTS SPECIFICATIONS.3/8 PANEL LAYOUT. 14 DIMENTIONS. 23 CIRCUIT BOARD LAYOUT. 24 BLOCK DIAGRAM. 26 DISASSEMBLY PROCEDURE. 31 HARD DISK INSTALLATION. 35 CD-RW DRIVE INSTALLATION . 37 I/O CAR

2、D INSTALLATION. 41 LSI PIN DESCRIPTION. 43 IC BLOCK DIAGRAM. 54 CIRCUIT BOARDS. 58 TEST PROGRAM.70/89 DISPLAY MESSAGE LIST .108/112 MIDI IMPLEMENTATION CHART . 116 MIDI DATA FORMAT . 117 PARTS LIST OVERALL CIRCUIT DIAGRAM This document is printed on chlorine free (ECF) paper with soy ink. PROFESSION

3、AL AUDIO WORKSTATION AW4416 only AW4416 + HDD AW4416 + HDD + CD-RW Hardware components Japanese U.S.A., Canadian, North European, British, Asian an “X” indicates a mismatch. b) If all bits are “X”, there is a problem with the CS or the Address bus. c) If only one bit is “X”, there is a problem with

4、the Data bus. AW4416 78 Checking MIX CPU HDR CPU . NG NG message NG message No response from HDR CPU a) Problem with Mixer CPU or HDR CPU interrupts. NG message MSBLSB 0XXX XXXX b) Problem in the CS, Address bus, or Data bus at the Mixer CPU or HDR CPU. To exit, press the CANCEL key. The program ret

5、urns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-6 DSP5 Function Test (06 DSP5) (1) Display (Test Screen Type D) 1) Test name DIAGNOSTIC for DSP5 (2) Test Content 1) Checks the MAIN CPU / DSP5 interface. 2) Checks the DSP5 bus connection and serial

6、 I/O and parallel I/O connections. (3) Judgment 1) Results area 1: Initialize all DSP5 . * 2: CPU Interface IC505 ERR = 0/10000 . * IC509 ERR = 0/10000 . * 3: SIO Connection DSP6 - DSP5 . * 4: SIO Connection DSP5 - DSP6 . * 5: SIO Connection DSP5 - DSP5 . * 6: PIO Connection DSP6 DSP5 . skip! ALL TE

7、ST ARE OK! Exit-method area EXIT: ENTER / CANCEL 2) If all tests are OK (if the overall result area displays the ALL TESTS ARE OK message): Press ENTER to return to the test menu. An appears in the left column, and the cursor advances to the next test in the menu. 3) If a check returns an NG: 1: Ini

8、tialize all DSP5 . NG NG message TRANS ERROR a) DSP5 initialization problem. 2: CPU Interface NG message IC505 ERR = 0/10000 . OK IC509 ERR = 10000/10000 . NG MSB28242016128LSB XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX a) Connection problem with IC509 Data bus, Address bus, R/W, or CS. 3: SIO Connecti

9、on DSP6 - DSP5 . NG NG message NG: IC301 SO0 - IC509 SIO16 a) IC301 SO0 - IC509 SIO16 connection problem. 4: SIO Connection DSP5 - DSP6 . NG NG message NG: IC505 SIO40 - IC301 SI0 a) IC505 SIO40 - IC301 SI0 connection problem. 5: SIO Connection DSP5 - DSP5 . NG NG message NG: IC505 SIO0 - IC509 SIO0

10、 a) IC505 SIO0 - IC509 SIO0 connection problem. 6: PIO Connection DSP5 - DSP5 . skip! not tested. To exit, press CANCEL. The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. AW4416 79 5-2-7 DSP6 Function Test (07 DSP6) (1) Display (Test Scre

11、en Type D) 1) Test name DIAGNOSTIC for DSP6 (2) Test Content 1) Checks the MAIN CPU DSP6 interface (DRAM). 2) Checks the DSP5 bus connection and serial I/O and parallel I/O connections. (3) Judgment 1) Results area 1: CPU Interface (Data bus). * 2: CPU Interface (Data bus). * 3: CPU Interface (Chip

12、Select, TXB).* 4: CPU Interface (Address bus). * 5: CPU Interface (BUS, W/R, Reg). * 6: DRAM Interface (Data bus). * 7: DRAM Interface (Address bus). * 8: DRAM Interface (Address bus 2nd day of month 02 Set hour using 1 - 24 system. Example: 8 PM 20. Set two-digit values for hour and minute. Example

13、s: 5AM 05; 7 minutes after the hour: 07 Do not set the seconds. The seconds count always starts from 00. Example: To set the date to April 21, 2000 and the time to 20:00:00, key in the numbers as follows. 3) Check When you press the ENTER key, the program returns to the test menu screen. Check the t

14、ime and battery information at the top right of the screen. 2000/04/2120:00:00 Fri Date and time that you just set. BATTERY OK Battery check 6. Miscellaneous (1) Not all switches include LEDs. In the following illustration, non-LED switches are indicated in gray . Note that these switches are not su

15、pposed to light up during the LED test (test 2 on the test menu). Key input sequence HDD ACCESS LED (with FL filter) This LED is not tested by the LED test (test 2 in the test menu). But please be sure that this LED blinks when you execute the IDE test (test 10 in the menu). AW4416 89 (2) The FADER

16、AGING test (test 30 in the menu) generates a series of fader operations. This is a special test that places the AW4416 into a special mode. Fader operation itself is tested by the FADER test (test 19 in the test menu). Note that at test program startup the test menu automatically shows an for the FA

17、DER AGING test. Note also that you can move the faders using the SONG, QUICK REC , MASTER ING , and CD PLAY buttons regardless of the test type. AW4416 90 AW4416 91 AW4416 92 AW4416 93 AW4416 94 AW4416 95 AW4416 96 AW4416 97 AW4416 98 AW4416 99 AW4416 100 AW4416 101 AW4416 102 AW4416 103 AW4416 104

18、AW4416 105 AW4416 106 AW4416 107 AW4416 108 Messages AUTOMIX DISABLED.Automix is not enabled, and cannot be recorded. AUTOMIX MEMORY FULL!Automix memory has no free area. AUTOMIX NOT RUNNING.Automix has been stopped, so recording is not possible. Pause the recorder, and then playback. AUTOMIX REC AB

19、ORTED.Automix recording was stopped, and the data was discarded. AUTOMIX RECORDING.The operation cannot be executed since automix is being recorded. AUTOMIX RUNNING.The operation cannot be executed since automix is being recorded or played. BANK A SELECTEDSince sampling pad bank A is selected, mutin

20、g cannot be defeated for this pad. BANK B SELECTEDSince sampling pad bank B is selected, muting cannot be defeated for this pad. CANNOT ASSIGN DIGITAL-ST-IN.DIGITAL STEREO IN cannot be assigned to the stereo bus cas- cade. CANNOT CHANGE THE MUTEMuting cannot be defeated since this would exceed the n

21、umber of simultaneously playable tracks. CANNOT PLAY THIS PAGEPlayback is not possible in this page. CANNOT RECALL AUTOMIXRecall is not possible, since automix data has not been stored. CANNOT REDORedo (re-execution of an operation) is not possible. CANNOT SELECT (MTC SLAVE)Since the AW4416 is set t

22、o be the MTC slave, the external word clock cannot be selected as the word clock source. CANNOT SELECT (WC EXTERNAL)Since the external word clock is selected as the word clock source, the AW4416 cannot be set as the MTC slave. CANNOT SET MARK It is not possible to specify a mark at an already-specif

23、i ed position. CANNOT UNDOUndo (cancellation of an operation) is not possible. CANNOT USE BOTH SLOTS!OPTION I/O slot 1 and slot 2 cannot be used simultaneously. CD PLAY MODE NOW.Since the AW4416 is in CD Play mode, this operation is not possi- ble. DIFFERENT TC FRAME TYPEMTC of a different frame typ

24、e than the internal setting is being received. DIGITAL-ST-IN REC PROHIBIT.Recording is prohibited for the signal being input from DIGITAL STEREO IN. DIGITAL-ST-IN SYNC ERROR!The signal being input from DIGITAL STEREO IN is not synchro- nized to the word clock master. DIN TO STEREO BUS REFUSE.Since t

25、he signal was interrupted, cascading from DIGITAL STE- REO IN to the stereo bus has been defeated. EFF1 INSERT RELEASEDEffect 1 has been released from insertion because a patch library was recalled. EFF2 INSERT RELEASEDEffect 2 has been released from insertion because a patch library was recalled. F

26、OR EFFECT2 ONLY.The selected effect program can be used only with effect 2. IN/OUT POINTS TOO CLOSEThe auto punch-in/out interval is too short. It cannot be set less than approximately 100 msec. DISPLAY MESSAGE LIST 109 AW4416 INT.EFF NOW SELECTED AUX.The internal effect is connected to the AUX send

27、, and cannot be inserted. LOW BATTERY!The internal battery is running down. MAKE NEW MIX.There are no events to be edited. Please create a new mix. MARK ERASEDThe mark has been erased. MARK SETThe mark has been set. MIDI IN: DATA FRAMING ERROR!Invalid data may have been received at the MIDI IN conne

28、ctor. MIDI IN: DATA OVERRUN!Invalid data may have been received at the MIDI IN connector. MIDI: RX BUFFER FULL!The AW4416 is receiving more MIDI data than it can handle. MIDI: TX BUFFER FULL!The AW4416 is attempting to transmit more MIDI data than it can handle. NO CURRENT AUTOMIX.There is no valid

29、automix data. Please create a new mix. NO DATA TO RECALL.Since data has not been stored, it cannot be recalled. NO MARK LEFTThe allowable number of marks has been exceeded. PLAY TRACK MUTE IS ONPlayback tracks were muted because the allowable number of simultaneously recorded/played tracks was excee

30、ded. RECORDER BUSYThe operation cannot be executed because the recorder is operat- ing. RECORDER RUNNINGThe operation cannot be executed because the recorder is record- ing or playing. REDO COMPLETERedo (re-execution of the previous operation) has been com- pleted. REPEAT POINTS TOO CLOSEThe repeat

31、interval is too short. It cannot be set to less than one second. SELECTED AREA HAS NO DATA.The selected area contains no trigger data. SELECTED AREA HAS NO REGION.The selected area contains no region. SELECTED CH IS NONE.The selected channel cannot be selected since it does not exist. SELECTED CH ON

32、LY MODE.The channel cannot be changed, since the display mode is set to SELECTED CH ONLY. SELECTED PAD NOT ASSIGNED.No sample is assigned to the selected sampling pad. SELECTED SONG HAS NO REGION.The selected song does not contain a region. SELECTED TRACK HAS NO REGION. The selected track does not c

33、ontain a region. SELECTED TRACK NOT RECORDED. The selected track does not contain recorded data. SLOT1 INPUT SYNC ERROR!The signal being input to the input jack of a card installed in OPTION I/O slot 1 is not synchronized to the word clock master. SLOT1,2 INPUT SYNC ERROR!The signal being input to t

34、he input jack of a card installed in an OPTION I/O slot is not synchronized to the word clock master. SLOT2 INPUT SYNC ERROR!The signal being input to the input jack of a card installed in OPTION I/O slot 2 is not synchronized to the word clock master. SOLO READY.The Solo function is ready. Use the

35、SEL keys to select the solo channel. SOLO SLAVE.The Solo status cannot be changed when the AW4416 is function- ing as a cascade slave. Press the Solo key on the master console. SONG NUMBER FULL.The maximum number of songs has been reached. SONG TOP/END OUT OF RANGEYou located outside the top/end ran

36、ge of the song. STEREO PAIRED.You are attempting to defeat ST LINK for the dynamics of paired channels. AW4416 110 Popup messages STEREO TRACK MUTE IS OFFSince muting is off for the stereo track, track muting cannot be turned off. THIS SONG IS PROTECTED.This song is protected, and cannot be edited o

37、r recorded. TO HOST: DATA FRAMING ERROR!Invalid data may have been received at the TO HOST connector. TO HOST: DATA OVERRUN!Invalid data may have been received at the TO HOST connector. TO HOST: DATA PARITY ERROR!Invalid data may have been received at the TO HOST connector. TO HOST: RX BUFFER FULL!E

38、xcessive amounts of data may have been received at the TO HOST connector. TO HOST: TX BUFFER FULL!The AW4416 may be attempting to transmit excessive amounts of data from the TO HOST connector. TRIGGER LIST RECORDINGA sampling pad trigger list is being recorded. UNDO COMPLETEUndo (cancellation of the

39、 previous operation) has been executed. WRONG WORD CLOCK!The word clock from a connected device selected by the AW4416 for synchronization is not appropriate. CD Access Error!A error occurred when accessing the CD. CD Size Full!Data exceeding the recordable length of the CD cannot be added. CD Track

40、 Over!The maximum number of tracks has been reached, and further addition is not possible. Cant Copy This Parameter!This parameter cannot be copied. Cant Create Image File! Since the disk is full, a CD image fi le cannot be created. Cant Delete Current Song!The currently loaded song cannot be delete

41、d. Cant Delete Protected Song! A protected song cannot be deleted. Cant Edit Multiple Songs!This editing operation cannot be executed on multiple songs simultaneously. Cant Optimize Protected Song!Optimize cannot be executed on a protected song. Cant REDORedo is not possible. Cant Select Current Son

42、g!The currently loaded song cannot be edited. Cant UNDOUndo is not possible. Cant Write CD-RW by Track At Once! A CD-RW cannot be written using Track At Once. Change Media, Invalid Order.Please exchange the media. The order of media volumes is incor- rect. Change Media, Not 1st Media Please exchange

43、 the media. This is not the fi rst media volume. Change Media, Not TYPE 1 Backup.Please exchange the media. This media was not backed up as TYPE 1. Change Media, Not TYPE 2 Backup.Please exchange the media. This media was not backed up as TYPE 2. Change Media, PleaseThe media is an incorrect type. P

44、lease exchange it. Device Error!A problem has occurred with the SCSI device. Directory Name Too Long!The directory name is too long and cannot be displayed. Directory Not Found! The specifi ed directory cannot be found. Disk Full!The disk has no free capacity. File System Error! An error has occurre

45、d in the fi le system of the internal hard disk. Finalized Media! The media has already been fi nalized. Invalid Parameter!The parameter setting exceeds the allowable range. 111 AW4416 Media Error!A problem has occurred on the media. Media Full!The media has no free space. Media Protected!The media

46、is write-protected. Memory Full!There is no free space in the sampling pad memory. No Song to Backup!There is no song to backup. No Song to Edit!There is no song to edit. No Song to Load!There is no song to load. No Song to Restore!There is no song to restore. No Song to Save!There is no song to sav

47、e. No Song to Write!No songs to write to the CD have been selected. No Song!No songs can be found. No Stereo Track!There is no stereo track. No Track to Open Wave Display!There is no track data for waveform display. Not WAV Drive! The selected drive contains no WAV fi les. Not WAV File! The fi le is not a WAV fi le. Partition Not Found! The specifi ed partition was not found. Recall Channel Data Confl ict! The specifi ed channel library cannot be loaded into this channel. SCSI Error!An error has occurred in t