Federal PA300 Service Supplement 电路图.pdf

《Federal PA300 Service Supplement 电路图.pdf》由会员分享，可在线阅读，更多相关《Federal PA300 Service Supplement 电路图.pdf（3页珍藏版）》请在收音机爱好者资料库上搜索。

1、-1- Control Cable Wiring Diagram. 256A680 REV. A 495 Printed In U.S.A. SUPPLEMENT SHEET TO MODEL PA300 SERVICE MANUAL FOR MODEL PA300*012-NY A.GENERAL. The 100-watt output of the basic Model PA300 was designed to drive a single high power speaker. However, the essential difference between models is

2、that the PA300*012-NY can drive one or two 11-ohm impedance, high or low power speakers. When two speakers are used they must be connected in parallel. B.MANUAL CHANGES. The following changes should be made to the Model PA300 Installation and Service Instructions (Part No. 255A198). 1.Page 2. Change

3、 the following paragraphs, as shown below: Frequency Range800 to 1800Hz Operating Current (14.0Vdc-WAIL) 1 Low Power Speaker5 amperes 2 Low Power Speakers10 amperes 1 High Power Speaker10 amperes 2 High Power Speakers15 amperes Voltage Output (approx.) 1 Low Power Speaker45Vp-p 2 Low Power Speakers4

4、0Vp-p 1 High Power Speaker64Vp-p 2 High Power Speakers60Vp-p 2.Page 4, paragraph 3-3.A. Speaker. Change to read: A.Speaker. The unit is designed to operate with one 11- ohm impedance speaker or two 11-ohm impedance low power (58W) or high power (100W) speakers, connected in parallel and in phase. On

5、 FEDERAL speakers, this can be accomplished by connecting the two speaker leads marked “1” to the SPEAKER COMMON control cable lead and the two speaker leads marked “2” to the SPEAKER HI POWER or SPEAKER LO POWER control cable leads See the Control Cable Wiring Diagram (new). A speaker is not includ

6、ed as part of the electronic siren. FEDERAL speakers are weatherproof and may be installed in any convenient location; on the roof, fender, behind the grill, etc. Any special mounting instructions applicable to the type of speaker you have selected will be found in the speaker carton. Using 18 gauge

7、 wire, connect the speaker leads (58W speakers to SPEAKER LO POWER and 100W speakers to SPEAKER HI POWER) as shown in the Control Cable Wiring Diagram (new). 3.Page 7, Paragraph 4-3.E. HI-LO. Change to read: E.HI-LO. This function is not available on the Model PA300*012-NY. 4.Page 7, Paragraph 4-4.

8、HORN/SIREN SWITCH. Change to read: The HORN/SIREN switch, located on the left side of the front panel, activates the peak-and-hold sound (down) in any position except radio. The air horn function is not available on the Model PA300*012- NY. 5.Page 8, Paragraph 4-6. PRESS AND HOLD FUNCTIONS. Change t

9、o read: PRESS AND HOLD FUNCTIONS SelectorPress onRelease of SwitchHorn RingHorn Ring PositionProducesProduces ManualPeak-and-Coast down Holdand silence RadioFans.CN 收音机爱 好者资料库 Component Location Detail. 6.Page 14. Refer to the component location diagram detail in this supplement to locate the addi-

10、tional PA300*012-NY components (R59, R60). 7.Page 15. A Model PA300*012-NY schematic diagram is included in this supplement sheet. 8.Page 16. Change the parts list as follows: a.Add:R59, 60- Resistor, 0.47 ohm, 2W, 10%. Part No. 130A130. b.Change the Part No. of T2 to 120C165A- 04. c.Change the Part No. of the Circuit Board (with parts installed) to 200C860-02. -2- RadioFans.CN 收音机爱 好者资料库 Model PA300*012-NY Schematic Diagram. -3-