Rauland 2417 Correction Module 电路图.pdf

《Rauland 2417 Correction Module 电路图.pdf》由会员分享，可在线阅读，更多相关《Rauland 2417 Correction Module 电路图.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、Installation KI-1354A 2417 Correction Module Rauland-Borg Corporation Issued: 07/01/98 Page 1 of 6 RadioFans.CN 收音机爱 好者资料库 Copyright 1998 by Rauland-Borg Corporation, all rights reserved. This document contains users information on technology that is proprietary to Rauland-Borg Corporation. Permitte

2、d transmittal, receipt, or possession of this document does not express license or imply any rights to use, sell, design or manufacture this information. No reproduction, publication, or disclosure of this information, in whole or in part, shall be made without prior written authorization from an of

3、ficer of Rauland-Borg Corporation. Rauland-Borg Corporation Rauland-Borg Corporation 3450 West Oakton Street Skokie, Illinois 60076-2958 (847) 679-0900 RadioFans.CN 收音机爱 好者资料库 KI-1354A 2417 Correction ModuleInstallation Table of Contents GENERAL INFORMATION. 4 DESCRIPTION. 4 REVISION HISTORY. 4 PACK

4、ING LIST. 5 DRAWINGS, DIAGRAMS, AND OTHER GRAPHICS. 5 INSTALLATION. 6 MECHANICAL INSTALLATION. 6 KI-1354A 2417 Correction ModuleInstallation Page 4 of 6 (Jul-98) General Information Description The Rauland 2417 Correction Module accepts serial data from the Master Clock and controls the power supply

5、 for the digital secondary clocks. The Correction Module also allows corrections in time control systems that use both digital and analog secondary clocks. One module is required for each twenty- five digital secondary clocks. It can be mounted inside either the 2415 (see KI- 1356) or the 2416 (see

6、KI-1355) Power Supply. A schematic of the 2417 is also attached. Revision History This manual has been reformatted. No substantive changes were made during the reformatting process. 1 KI-1354A 2417 Correction ModuleInstallation Page 5 of 6 (Jul-98) Packing List The 2417 consists of the following: Qu

7、antityPartPart Number 4Circuit Board Support QP0656-1 1Circuit Board Assembly VC7044 Drawings, Diagrams, and Other Graphics This document includes the following drawings, diagrams, and/or supplemental graphics: ? 2415 24-VAC Power Supply Drawing (KM0609) ? 2416 120-VAC Power Supply Drawing (KM0610)

8、? 2417 Correction Module Installation Drawing (KM0610) ? KC1429 KI-1354A 2417 Correction ModuleInstallation Page 6 of 6 (Jul-98) Installation Mechanical Installation Refer to figure 1 for either the 2415 or the 2416. 1. Make sure that the AC power to the master clock is disconnected. 2. Remove the t

9、hree WA6 screws securing the AN1006 cover, then remove the cover. 3. Insert the four QP0656-1 circuit board supports into the four holes of the adapter module. 4. Align the adapter module, with its foil side towards the inside of the chassis, opposite the transformer. snap the circuit board supports

10、 into the four holes in the chassis wall. 5. Refer to the wiring diagrams in either KM0609 (2415) or KM0610 (2416) for related wiring information and make the electrical connections. Select a knockout for the electrical wiring. 6. Replace the AN1006 cover and fasten it with the three WA6 screws you previously removed. Depress the circuit breaker several times to be sure it does not bind after the cover is replaced. 7. Program the Master Clock according to normal procedures provided in its manual. 2