Rauland Ranger Baseband 电路图.pdf

《Rauland Ranger Baseband 电路图.pdf》由会员分享，可在线阅读，更多相关《Rauland Ranger Baseband 电路图.pdf（28页珍藏版）》请在收音机爱好者资料库上搜索。

1、Rauland RANGER System Planning Baseband Components The following table lists the required and optional components used in a baseband system. Some of these components may be fabricated. Table 6. Required RANCAGE Card Cage Optional RANMENU Character Generator (recommended) RANxxVSyy (or equivalent swi

2、tcher) RANAVMSP Audio/Video Multiplexer Module RANAVDSP Audio/Video Demultiplexer Module RANAVJ Audio and Video Jack RANEXPAD Master Port Expander (if have RANEXP and need more than 12 ports) RANBROAD Master Port Expander RANSYNCR Sync Generator RANDTMF Interface Board (for control via phone) In a f

3、iber system: RANFT4/RANFT4FM or RANFTl/RANFTlFM Transmitter Cards RANRELAYB or RANRELAYl4 Universal Relay Card (required if devices are relay controlled) RANCCI 6 Control Card Cage RANIRIS Infrared Capture Unit (for custom IR codes) RANCPU Control System Master Card or RANEXP Master Port Expander RA

4、NCLASSI Classroom Control Panel RANIR and/or RAN232 (Control Cards) RANCLl 01 or RANCLl 01 CP Classroom Controller TV Interface Boxes: RANCLINTF for coax systems or RANFBINT for fiber systems RANDATA Level Ill Laser Disc Controller Television Monitors RANAVMSI Audio/Video Multiplexer Module (for dis

5、tributed local origination) Resources (RANLASER, RANVCR, etc.) RANPCVID Super Video Windows Card RANPSI 2 Power Supply RANHHELD Remote Control 7/l l/95 Chapter 3: Baseband, Page 37 RadioFans.CN 收音机爱 好者资料库 Rauland RANGER System Planning Communication Company of South Bend. Roiling Prarie Elementary,

6、S.O. C428634 RAN-024 VI .O Rack Layout: (3) 61 Racks Rack 1 Rack1 RANMONI 3 RANMONMNT RAN50X20 27 28 El- 29 30 31 RAN50VS20 Rack 2 VCR6 w/ RANSHELF (Tuner Only) VCR7 w/ RANSHELF (Tuner Only) VCR8 w/ RANSHELF (Tuner Only) PC MONITOR W/ RANMONMNT BP1 KEYBOARD w/ RANKEYMNT VFLOPI w/ RANSHELF RANPCSW w/

7、 RANSHELF RANMENU w/ RANSHELF RANCCI 6 RANCAGE w/ RANSHELF w/ RANSHELF w/ RANSHELF w/ RANSHELF Leave open for customer Amp. Figure 7. Typical Baseband Rack Layout Diagram 7/11/95 Chapter 3: Baseband, Page 39 Rauland RANGER System Planning Pre-Ins talla tion lnforma tion RANCLI 01 and RANCLI 01 CP Cl

8、assroom Controllers l You will need to pull one video cable or one fiber-optic cable to each location that will receive video from the headend. If a classroom has distributed local origination, an additional coax or fiber video cable will be required, as well as additional hardware (RANAVMSI and RAN

9、FTl for fiber). If using RS485 control in the classroom, an additional l-pair shielded data-grade wire will also need to be pulled. For more information refer to the Installation manual, KI-I 856. l If a RANCLINTF classroom cable interface plate is used in a coax-based system, the 2-gang box that wi

10、ll hold the RANCLINTF must be mounted within five feet of the RANCLIOI or RANCLIOICP Classroom Controller. l For fiber systems, an 8 x 10 x 4 backbox (RANBOX4) is required to hold the RANFBINT TV Interface Box. It should be mounted within 5 feet of the RANCLlOl or RANCLIOICP. l The l-pair shielded w

11、ire can be looped from one classroom to another as long as it does not exceed the maximum distance per AXLINK port specified in the documentation for the RANEXP Master Port Expander, RANEXPAD Master Port Expander, RANBROAD Master Port Expander, or RANCPU Control System Master Card. The control pair

12、can also run on independent AXLINKS. Each link is subject to the specifications for maximum distance per AXLINK port specified. l If using a RANAVJ Audio and Video Jack, a single-gang electrical box must be mounted so that it is easily accessible for the local device (e.g., camera) that will be plug

13、ged in. Install an RG59 (or equivalent) cable and one shielded-pair to the RANCLINTF TV Interface Box. l If using a RANDATA for Level III laser disc control, a single-gang electrical box must be mounted so that it is near the computer running the Level III program. Install one shielded data-grade pa

14、ir from the RANDATA to the RANCLINTF TV Interface Box. Headend Video RANCAGE Card Cage The RANCAGE is a card cage that houses Fiber, Multiplexer, and Demultiplexer cards used with a RANGER system (RANAVMS2, RANAVDS2, RANFT4, or RANFR4). This cage holds any combinaiion of ten cards regardless of the

15、type of card. The RANCAGE requires 12 VDC at 20 mA and mounts in a four-rack unit (7”) space. Parts Required 4 Mounting screws (RB Part # B0439) and 4 washers (RB Part # WL03 15) Chapter 3: Baseband, Page 40 7/l l/95 Rauland RANGER System Planning Note: The RANxx VSyy is a modular unit. The xx and y

16、y ore variables that refer to the capacig of the switch. .yx=inputs and yy=outputs. 1 2-pin Phoenix connector (supplied with the RANCAGE) 1 Pair of twisted red and black 18 ga. wire for power Associated Equipment 1 12 VDC power source (e.g., RANPS12) RANAVMS2, RANFT4, RANFR4, RANAVDS2 RANxxVSyy Vide

17、o Matrix /Auto Patch Switchers RANxxVSyy and Auto Patch Switchers are video matrix switches designed to connect system inputs (typically media devices or locally originated broadcasts) to output locations (typically classrooms) in baseband RANGER systems. Connection between classrooms and the media

18、center are controlled through the RANCPU Control System Master Card which interfaces to the Video Matrix Switch via an RS232 connection. The switch then connects to the source device or other audio/video inputs through a multiplexer module (RANAVMS2) permitting the use of a video-only switch. The RA

19、NxxVSyy is available in increments of ten inputs and ten outputs. The Auto Patch Switcher is available in increments of four inputs and four outputs. Parts Required 1 Interface cable (refer to drawing VW2374 for the RANxxVSyy switch and VW2375 for the Autopatch switch) 1 Power cord (supplied with th

20、e switch) 1 RAN232 Serial Control Card (see “RAN232” for more information) Associated Equipment 1 RANCC16 Control Card Cage (see “RANCC16” for more information) 8 Mounting screws (RB Part # B0439) and 8 washers (RB Part # WLO315) for RANIVSYYI RANA VMS2 Audio/Video Multiplexer Module The RANAVMS2 is

21、 a stereo audio/video multiplexer module that combines a media resources audio and video signals onto one 75Q coax cable. This cable then connects to the video matrix switch, which then passes the signal over another 75Q coax, cable to the classroom. The RANAVMS:! consists of two multiplexer modules

22、 on one PC board allowing two resources to be connected to one RANAVMS2. These stereo audio/video multiplexer modules are housed in a RANCAGE card cage with a 12 VDC at 400 mA power source. 7/l l/95 Chapter 3: Baseband, Page 4 1 Rauland RANGER System Planning Parts Required 1 75Q video cable with Ph

23、ono to Phono connectors (refer to drawing VW2377) or Phono to BNC (refer to drawing VW2376) for RANVFLOP and RANSVHS 1 or Phono to Phono audio cable (refer to drawing VW2385). Separate left and right 2 leads for stereo sources. Mono audio sources will only need 1 cable. 1 75Q video cable with Phono

24、to BNC connectors for composite out to the video matrix switch input (refer to drawing VW2376) Associated Equipment 1 RANCAGE Card Cage (see “RANCAGE” for more information) 1 RANPS 12 Power Supply 1 Media device (e.g., RANVCR, RANCDI, RANLASER, RANVFLOP, or RANMENU) RANA VDS2 Audio/Video Demultiplex

25、er Module The RANAVDS2 is a stereo Audio/Video Demultiplexer module that takes a combined Video Matrix Switch output signal and converts that signal back to separate audio and video signals. The RANAVDS2 consists of two demultiplexer modules on one PC board allowing two resources to be connected to

26、one RANAVDS2. These stereo audio/video demultiplexer modules are housed in a RANCAGE Card Cage with a 12 VDC at 400 mA power source. They are usually used in conjunction with an operator console or preview monitor (e.g., RANMON13). Parts Required 1 75Q video cable with Phono to Phono connectors (ref

27、er to drawing VW2377) or Phono to BNC (refer to drawing VW2376) for RANVFLOP and RANSVHS 1 or Phono to Phono audio cable (refer to drawing VW2385) 2 1 75Q video cable with Phono to BNC connectors for composite out to the Video Matrix Switch output (refer to drawing VW2376) Associated Equipment 1 RAN

28、CAGE Card Cage (see “RANCAGE” for more information.) 1 RANPS12 Power Supply 1 Output device (e.g., RANMON13 or RANPCVID). Chapter 3: Baseband, Page 42 7/l l/95 Rauland RANGER System Planning RANSYNCR Sync Generator The RANSYNCR is a black and white camera which produces a sync pulse that is needed t

29、o keep the RANGER systems video output in sync when no resource is assigned to a classroom monitor. It mounts on the side of one of the media center equipment racks and requires a 24 VAC power supply. Parts Required 1 VP0266 (24VAC power supply) 2 BNC to Phono 75R video cables (refer to drawing VW23

30、76) Associated Equipment 1 3-conductor wire to interconnect the VP0266 to RANSYNCR RANFT4/RANFT4FM or RANFTl/RANFT7FM Fiber Transmitter Card These transmitter cards convert a coax signal to fiber. The RANFT4 is an AM Quad Fiber Transmitter Card that transfers a baseband audio/video signal from the v

31、ideo switcher over a fiber-optic cable to a classroom (the RANFTI is a single module). In fiber optic based systems one RANFT4 is required for every four outputs (classrooms). While these modules are not required for baseband coax systems, it is possible to have some outputs that are fiber optic and

32、 some that are coaxial. The RANFT4FM and RANFTlFM are FM versions of the RANFT4 and RANFTI. Each transmitter mounts in the RANCAGE Card Cage, and requires 12 VDC at 280 mA. Parts Required 1 RANCAGE Card Cage (to mount the RANFT4 or RANFT4FM) 1 RANFBINT TV Interface Box (to mount the RANFRl or RANFR

33、1FM) Associated Equipment 1 Multimode Fiber-Optic cable 1 BNC to BNC 750 video cable (refer to drawing VW2375) for the RANFT4 RANFR4/RANFR4FM or RANFR 7/RANFR I FM Fiber Receiver Card These receiver cards convert a fiber signal back to coax. The RANFR4 is an AM Quad Fiber Receiver Card that receives

34、 a baseband audio/video signal from the video switcher over a fiber-optic cable to a classroom (the RANFRl is a single module). In fiber-optic based systems one RANFRI is required for each classroom that is receiving a fiber Chapter 3: Baseband, Page 43 Rauland RANGER System Planning signal. One RAN

35、FR4 is required for every four classrooms that have distributed local origination. While these modules are not required for baseband coax systems, it is possible to have some inputs that are fiber optic and some that are coaxial. The RANFR4FM and RANFRIFM are FM versions of the RANFR4 and RANFRl. Ea

36、ch receiver mounts in the RANCAGE Card Cage, and requires 12 VDC at 340 mA. Parts Required 1 RANCAGE Card Cage (to mount the RANFR4 or RANFR4FM) 1 RANFBINT TV Interface Box (to mount the RANFTI or RANFTIFM) Associated Equipment 1 Multimode Fiber Optic cable 1 BNC to BNC 75L2 video cable (refer to dr

37、awing VW2375) for the RANFR4 RANMENU Character Generator VGA to NTSC RANMENU uses an IBM compatible PC to generate and display classroom TV menus for the RANGER system. A PC running RANMENU software interprets live serial data fed from a RAN232 Serial Control Card housed in the RANCC16 Control Card

38、Cage. The data is formatted and sent to the computer VGA video output where it is then converted to a composite NTSC signal via a VGALNTSC scan converter. The video output is then redirected through the method used for video distribution. The RANMENU is comprised of software, interface cable, and a

39、VGA/NTSC converter. Rauland-Borg does not supply a computer. The RANMENU software requires an 8088 or better computer capable of displaying VGA color graphics. The computer requires a license for DOS 3.3 or better, a floppy drive and a RS232 port. No monitor, keyboard, or hard drive is required. Par

40、ts Required 1 RANAVMS2 Audio/Video Multiplexer Module 1 Phono to Phono 75Q video cable (refer to drawing VW2385) 1 Phono to Phono 7552 video cable (refer to drawing VW2377) 1 Interface Serial Port cable (refer to drawing VW2353) Associated Equipment 1 RAN232 Serial Control Card (see “RAN232” for mor

41、e information) 1 RANCC16 Control Card Cage (see “RANCC16” for more information) Chapter 3: Baseband, Page 44 7/l l/95 Rauland RANGER System Planning 1 Terminal punch-block (Graybar SS66B3-75) 1 RANPS 12 Power Supply 1 RANDATXCR (one per building) RANEXPAD Master Port Expander The RANEXPAD is a Maste

42、r Port Expander that is used when you require additional ports beyond those available on a RANEXP (12+). You must have at least one RANEXP before you can add a RANEXPAD. Each RANEXPAD adds an additional set of twelve runs of cable (with a maximum of 60,000 pf). It requires 12 VDC at 200 mu and is mo

43、unted in a one rack unit (1.75”) space. The RANEXPAD must be mounted in the same rack as the RANEXP. 1 12 4 1 1 1 1 1 Parts Required RANEXP Master Port Expander 4-pin Phoenix connector (supplied with the RANEXPAD) Mounting screws and washers (supplied with the RANEXPAD) or 4 mounting screws (RB Part

44、 # BO439) and 4 washers (RB Part # WL0315) Connecting loop cable (1 supplied per unit) Pair shielded cable for connecting AMX Control Link Associated Equipment 6-terminal punch block (Graybar part # S66B3-75) RANCC16 Control Card Cage 12 VDC Power Source (e.g., RANPS12) RAN.232 Serial Control Card M

45、any of the RANGER systems devices are controlled via RS-232 control. In order to provide a universal operating interface for all media devices, the RANGER system emulates these devices original remote control units with the RAN232, a serial control card that fits in the RANCC16 Control Card Cage. Ea

46、ch device controlled via RS-232 serial commands (e.g., RANLASER, RANxxVSyy Video Matrix Switch, RANMENU Character Generator, and RANPCSW Media Center Computer) must have a RAN232 card associated with it. Additionally these cards must be appropriately configured for the communication parameters of th

47、e associated device. The RAN232 card mounts in the RANCCIG Control Card Cage and requires a 12VDC at 45mA power source. 7/l l/95 Chapter 3: Baseband, Page 49 Rauland RANGER System Planning . Parts Required 1 Interface serial cable (check the table below for the appropriate cable for the device that

48、you are configuring) Associated Equipment 1 RANCC16 Control Card Cage (see “RANCC16” for more information) Table IO. Cable/Resource Requirements Type of cable Type of resource VW2378 RANPCSW (Media Center Computer) VW2374 RANxxVSyy (Video Matrix Switch) VW2292 RANLASER VW2378 RANMENU (Character Gene

49、rator) VW2395 AutoPatch Video Matrix Switch w/v2353 RANTITLER (Tltler) VW2381 VP0229 (AVS2) RANIR Infrared Control Card Many of the devices that are operated through the RANGER system are controlled via infrared control. In order to provide a universal operating interface for all media devices, the RANGER system emulates these devices original remote control units