Rauland Ranger Head End 电路图.pdf

《Rauland Ranger Head End 电路图.pdf》由会员分享，可在线阅读，更多相关《Rauland Ranger Head End 电路图.pdf（55页珍藏版）》请在收音机爱好者资料库上搜索。

1、Installation KI-1856C Rauland RANGER Head End Rauland-Borg Corporation Issued: 06/26/98 Page 1 of 55 RadioFans.CN 收音机爱 好者资料库 Copyright 1998 by Rauland-Borg Corporation, all rights reserved. This document contains users information on technology that is proprietary to Rauland-Borg Corporation. Permit

2、ted transmittal, receipt, or possession of this document does not express license or imply any rights to use, sell, design or manufacture this information. No reproduction, publication, or disclosure of this information, in whole or in part, shall be made without prior written authorization from an

3、officer of Rauland-Borg Corporation. Rauland-Borg Corporation 3450 West Oakton Street Skokie, Illinois 60076-2958 (847) 679-0900 RadioFans.CN 收音机爱 好者资料库 KI-1856C Rauland RANGER Head EndInstallation Table of Contents INSTALLATION. 4 RANCAGE FIBER, MULTIPLEXER, AND DEMULTIPLEXER CARD CAGE. 4 RANAVMS2

4、STEREO AUDIO/VIDEO MULTIPLEXER MODULE. 5 Adjusting the RANAVMS2. 6 RANFT4/RANFT4FM OR RANFT1/RANFT1FM FIBER TRANSMITTER CARDS AND MODULES. 6 RANXXVSYY VIDEO MATRIX SWITCHERS (UTAH OR AUTOPATCH). 8 Configuring/Wiring the RANxxVSyys RAN232 . 9 Configuring/Wiring the Autopatchs RAN232. 9 RANCC16 CONTRO

5、L CARD CAGE.10 Installation.11 RANCPU CONTROL SYSTEM MASTER CARD.13 RANEXP MASTER PORT EXPANDER, RANBROAD EXPANDER.15 RANBROAD MASTER PORT EXPANDER.18 Front Panel LEDs.22 RANEXPAD MASTER PORT EXPANDER.23 CONNECTIONS AND SETTINGS OF THE CONTROL PC.23 Wiring of the Control PC and Hardware Settings .24

6、 Software Settings.24 RAN232 SERIAL CONTROL CARD.24 RANIR INFRARED CONTROL CARD.26 Downloading IR codes to a RANIR card.27 Wiring IR Transmitter Cables .33 RANIRIS INFRARED CAPTURE UNIT.33 Capturing a New Function.35 RANDTMF INTERFACE BOARD.42 Configuring the Media Center for a DTMF Classroom for Sy

7、stems with no Caller ID or Intercept Zone Information .43 Caller ID or Intercept Zone with DTMF Classrooms and DTMF Cards.44 RANRELAY8 UNIVERSAL RELAY CARD.46 Configuring Mediapc.ini for Alarms Triggered by Relays .47 Programming the RANRELAY8 as a Resource Controller.49 RANPCIR WINDOWS PC AIR MOUSE

8、.50 RANPCSW MEDIA CENTER COMPUTER.51 RANSYNCR SYNC PULSE CAMERA.53 RANMENU CHARACTER GENERATOR.53 APPENDIX.55 Rauland RANGER Headend Cable Summary .55 KI-1856C Rauland RANGER Head EndInstallation Page 4 of 55 (Jun-98) Installation RANCAGE Fiber, Multiplexer, and Demultiplexer Card Cage The RANCAGE i

9、s a card cage that houses Fiber, Multiplexer, and Demultiplexer cards used with a RANGER system (RANAVMS2, RANAVDS2, RANFT4, or RANFR4). This cage holds any combination of ten cards regardless of the type of card. The RANCAGE requires 12 VDC at 20 mA and mounts in a four-rack unit (7) space. Parts R

10、equired 4Mounting screws (RB Part # B0439) and 4 washers (RB Part # WL0315) (supplied with the RANCAGE) 1Pair of twisted 18-gage wires (red and black) for power Associated Equipment 112 VDC power source (e.g., RANPS12) RANAVMS2, RANFT4, RANFR4, RANAVDS2 Installation 1. Mount the RANCAGE into the rac

11、k. 2. Connect the 18-gage red wire to the positive terminal of the power supply (e.g., RANPS12) and the black wire to the negative terminal. 3. Connect the other end of the 18-gage wires to the two-pin terminal strip on the back of the RANGAGE. Be sure to connect the red wire to the positive side of

12、 the two-pin plug and the black wire to the negative side (see the silk screening on the back of the unit for the proper locations). 4. Install the necessary cards for your resources and follow the appropriate installation instructions (see “RANAVMS2,” “RANFR4,” and “RANFT4” for more information reg

13、arding their specific requirements). 1 KI-1856C Rauland RANGER Head EndInstallation Page 5 of 55 (Jun-98) RANAVMS2 Stereo Audio/Video Multiplexer Module The RANAVMS2 is a stereo audio/video multiplexer module that combines a media resources audio and video signals onto one 75 coax cable. This cable

14、then connects to the video matrix switch, which then passes the signal over another 75 coax cable to the classroom. The RANAVMS2 consists of two multiplexer modules on one PC board allowing two resources to be connected to one RANAVMS2. These stereo audio/video multiplexer modules are housed in a RA

15、NCAGE card cage with a 12 VDC at 400 mA power source. Parts Required 175 video cable with Phono-to-Phono connectors (refer to drawing VW2377) or Phono-to-BNC (refer to drawing VW2376) for RANVFLOP and RANSVHS 2Phono-to-Phono audio cable (refer to drawing VW2385). Separate left and right leads for st

16、ereo sources. Mono audio sources will only need one cable. 175 video cable with Phono-to-BNC connectors for composite out to the video matrix switch input (refer to drawing VW2376) Associated Equipment 1RANCAGE Card Cage (see “RANCAGE” for more information) 1RANPS12 Power Supply 1Media device (e.g.,

17、 RANVCR, RANCDI, RANLASER, RANVFLOP, or RANMENU) Installation 1. Remove the front cover panel of the RANCAGE card cage. 2. Insert the RANAVMS2 into the front of the card cage along the card guides (located on the top and bottom of the card cage) until it snaps into place. 3. Place the resource (e.g.

18、, a VCR Player) onto its appropriate rack shelf. Now place the device and shelf into the rack. 4. Route a video cable from the media devices “Video Out” jack to the “Video In” jack on the RANAVMS2 module that you have designated for this device. 5. If this device has audio, route the audio cables fr

19、om the media devices Left and Right “Audio Out” jack to the corresponding “Audio In” jacks on the RANAVMS2 module that you have designated for this device. This must be the same module that you have chosen for the video feed from that device. If it is a mono unit, select the Right audio input on the

20、 RANAVMS2. 6. Set the Stereo/Mono switch on the RANAVMS2 to the appropriate setting for the device. For devices without audio, select “Mono.” 7. Set the Audio Impedance switch to the appropriate settings for the device that you are using. Most devices use the 600 setting. Use the 10k setting for dev

21、ices whose KI-1856C Rauland RANGER Head EndInstallation Page 6 of 55 (Jun-98) audio output needs to be boosted (e.g., the Pioneer Laser Disc playersRANLASER). For devices without audio, select “600 .” 8. Route a cable from “Composite Video Out” (located on the back of the board) on the RANAVMS2 to a

22、n input jack on the video matrix switch. Note the input number that you have chosen. Adjusting the RANAVMS2 Once the system is operational and classrooms are on-line, it is important to adjust the RANAVMS2 multiplexer so that all of a systems media resources play at the same relative volume. We sugg

23、est using the operator console as your output source, because it is likely to be adjacent to the multiplexer module that you are adjusting. To adjust the RANAVMS2: 1. Turn on the media device and load it with the appropriate media. Start the unit and locate a loud passage. 2. Adjust the Audio Level

24、on the multiplexer module so that the “Overload” LED only comes on at very infrequent loud passages. If there is no audio source, turn this control completely counterclockwise. RANFT4/RANFT4FM or RANFT1/RANFT1FM Fiber Transmitter Cards and Modules V I n Fi ber O ut These transmitter cards convert a

25、coax signal to fiber. The RANFT4 is an AM Quad Fiber Transmitter Card that transfers a baseband audio/video signal from the video switcher over a multimode fiber-optic cable to a classroom (the RANFT1 is a single module). In fiber-optic based systems one RANFT4 is required for every four outputs (cl

26、assrooms). While these modules are not required for baseband coax systems, it is possible to have some outputs that are fiber optic and some that are coaxial. The RANFT4FM and RANFT1FM are FM versions of the RANFT4 and RANFT1. Each transmitter mounts in the RANCAGE Card Cage, and requires 12 VDC at

27、280 mA. Parts Required 1RANCAGE Card Cage (to mount the RANFT4 or RANFT4FM) 1RANFBINT TV Interface Box (to mount the RANFR1 or RANFR1FM) Associated Equipment 1Multimode Fiber-Optic cable 1BNC-to-BNC 75 video cable (refer to drawing VW2375) for each of the four channels of the RANFT4 Installation 1.

28、If it is not already off, remove the front cover of the RANCAGE card cage. KI-1856C Rauland RANGER Head EndInstallation Page 7 of 55 (Jun-98) 2. Insert the RANFT4 or RANFT4FM into the front of the card cage using the two metal card guides (located on the top and bottom of the card cage) until it sna

29、ps into place. 3. Connect a BNC-to-BNC 75 video cable (see drawing VW2375) from the BNC jack on the RANFT4 or RANFT4FM to one of the output jacks of the RANxxVSyy Video Matrix Switch. Figure 1. Wiring for Fiber Transmitters. 1. Connect the appropriate multimode fiber-optic cable strand to the RANFT4

30、 or RANFT4FMs designated outputs fiber jack. The eventual destination of this strand will be the Optical Input jack on the RANFR1 or RANFR1FM (as shown in the figure above). Note that all connectors for the fiber-optic cables must be the ST type. KI-1856C Rauland RANGER Head EndInstallation Page 8 o

31、f 55 (Jun-98) RANxxVSyy Video Matrix Switchers (Utah or AutoPatch) Note: The RANxxVSyy is a modular unit. The xx and yy are variables that refer to the capacity of the switch: xx=inputs and yy=outputs. RANxxVSyy and AutoPatch Switchers are video matrix switches designed to connect system inputs (typ

32、ically media devices or locally originated broadcasts) to output locations (typically classrooms) in baseband RANGER systems. Switchers are also used in mixed baseband/broadband systems as inputs to modulators. Connections between classrooms and the media center are controlled through the RANCPU Con

33、trol System Master Card, which interfaces to the Video Matrix Switch via an RAN232 connection. The switch then connects to the source device or other audio/video inputs through a multiplexer module (RANAVMS2) permitting the use of a video-only switch. The RANxxVSyy is available in increments of ten

34、inputs and ten outputs. The AutoPatch Switcher is available in increments of four inputs and four outputs. If the system is a switched broadband system, specify that the audio option be included, and do not use the RANAVMS2 or the RANAVDS2. Parts Required 1Interface cable (refer to drawing VW2374 fo

35、r the RANxxVSyy switch and VW2395 for the Autopatch switch) 1Power cord (supplied with the switch) 1RAN232 Serial Control Card (see “RAN232” for more information) Associated Equipment 1RANCC16 Control Card Cage (see “RANCC16” for more information) 8Mounting screws (RB Part # B0439) and 8 washers (RB

36、 Part # WL0315) for RANxxVSyy Installation 1. Typically the RANxxVSyy itself will not be set up in the field and the steps detailed here will not need to be carried out by field personnel. These instructions are provided for reference purposes. Warning: Before handling the control card, discharge static electricity from your cl