Rauland Tc4222 Display Installation 电路图.pdf

《Rauland Tc4222 Display Installation 电路图.pdf》由会员分享，可在线阅读，更多相关《Rauland Tc4222 Display Installation 电路图.pdf（6页珍藏版）》请在收音机爱好者资料库上搜索。

1、KI-1683C TC4222 Vacuum Fluorescent Display Installation RAULAND-BORG CORPORATION l 3450 West Oakton Street, Skokie, Illinois 60076-2951 l (847) 679-0900 General Information Description Planning The TC4222 Vacuum Fluorescent Display (“VFD”) may be used as an alternative to the LCD displays of the Tel

2、ecenter Systems. The TC4222 is larger and brighter than an LCD module and, being wall-mounted, can serve as the display for several nearby administrative phones. It is compatibIe with Telecenter IV, Telecenter V, Telecenter TCS, Telecenter System 21, and Telecenter 1100 systems. Attachments IL0364 (

3、Installation Diagram). The TC4222 connects to one of the two LCD drivers on the Main Input/Output (MIO) module. Each LCD driver accommodates up to three displays (LCD or VFD, in any combination) and a total cable length of 1,000 feet. Refer to the System Wiring Diagram (KMO674) in the main Telecente

4、r IV manual (KI-1435) as well as to the attached drawings. Parts Enclosed Qty. Description Part No. 1 VFD printed-circuit-board assembly, VC7461 1 Chassis (without the transformer and the A3614 ground wire). 1 Power transformer (mounted on the chas- LP0442 sis). 1 Front panel. QP0992 3 Wire nuts. QP

5、0488 1 Three-pin connector. SF0475-3 2 Screws (6-32 x 1/4 panhead) for attaching WA57 the chassis to the back- box. 4 Screws (6-32 x 1” black flathead Phillips) WA114 for attaching the front panel. The TC4222 connects to the primary display-driver ter- minals of the Central Input/Output (CIO) module

6、. The primary display-driver can accommodate up to 16 displays (LCD or VFD, in any combination), and a total cable length of 2,000 feet of 22-AWG wire. Refer to the System Wiring Diagram (KM1035) in the main Telecenter V manual (KI- 1687) as well as to the attached drawings. The TC4222 connects to t

7、he primary display-driver ter- minalS of the SAC Master-Port punchblock. The primary display-driver can accommodate up to 16 displays (LCD or VFD, in any combination), and a total cable length of 1,000 feet of 22-AWG wire. Refer to the System Wiring Diagram (KM1121) and to the other attached drawing

8、s. TCIV Installations TCV Installations TC2100 Installations Installation Mount the display in a back-box that has a five-gang opening and a minimum depth of 2 1/2 inches. 0 Carefully remove the seven-pin connector from the circuit-board assembly. Put the assembly aside in a safe Pull through the ho

9、le the three-conductor AC power place. lines and the 22-gauge shielded pair from an LCD driver, Orient the chassis assembly horizontally, with the Caution: Do not apply power to the AC lines until transformer to the right. Insert it into the electrical box, this installation has been completed. maki

10、ng sure that the wires are not pinched. Secure the 0 1995 RAULANC-BORG CORFWATION l Printed in U.S.A. Page 1 of 6 Orig. 5/92. Rev. 8/92. 9/93. 2/95. 168303 RadioFans.CN 收音机爱 好者资料库 TC4222 Vacuum Fluorescent Display Installation chassis to the box by inserting the two supplied #6-32 x 1/4 screws into

11、its top and bottom center holes. 6 Using the three supplied wire nuts, attach the two black transformer wires to the two main power lines (typically black and white). Then attach the green grounding wire to the third (safety ground) wire of the power line (typically green, also). Press these wires i

12、nside the chassis so there will be ample room to insert the VFD assembly. 8 Orient the three-pin connector so that the larger ends of the holes (containing the insulation-piercing sockets) are to the left and the exposed side is facing upward. 8 Insert the wires from the LCD driver into the insulati

13、on- piercing sockets of the connector. Route the wires into the connector at a right angle from the top; do not strip insulation from the ends of the wires. An insertion tool, such as Rauland s G2522, would be helpful. Refer to the appropriate wiring table on the right. I Orient the VFD assembly hor

14、izontally, with the seven- pin terminal (“J5”) to the right. Push the seven-wire connector onto this terminal with the red wire coming out from the bottom. Now push the three-wire connec- tor onto the three-pin terminal (J9”) located on the left side of the board; the shield should be at the bottom.

15、 The pin designations are marked on the printed circuit board and are referred to on the attached IL0364. 8 Making sure that all the wires are routed inside the electrical box, carefully insert the VFD assembly into the chassis 8 Using the #6-32 x 1” black flathead Phillips screws, carefully install

16、 the front panel. TCIV wiring Terminal of LCD driver on TC4222 3-terminal MIO “B” connector - “+” *” Top (“RED”) Middle (“BLK”) I “SHIELD” I Bottom (“SHIELD”) 1 TCV Wiring “SHIELD” Bottom (“SHIELD”) TC2100 Wiring connector Setting the DIP Switch Overview The eight-position DIP switch on the back of

17、the display configures the unit for different systems. Important: The TC4222 checks the DIP-switch settings only when it is powered up. Unless its power has been cycled off and back on, it will ignore changes made while it is running. Telecenter V and Telecenter System 21 For TCV or TC2100 operation

18、, push slide switch 8 Off and 5 On. (This selects the Telecenter V or Telecenter System 21 mode of operation.) The Display DIP Switch J tllliJozl!Jootloooclclclo laameaaQ 1 1 Baud Rate Display Address Set slide switches 1-4 to give each display a different address (the settings correspond to binary

19、numbers, with the least-significant digit on the right). Refer to the table below. v / System Type Display Address (TCV shown) (Address 0 shown) Page 2 2/95 RadioFans.CN 收音机爱 好者资料库 TC4222 Vacuum Fluorescent Display Installation . TC4221 DIP-Switch Summary On = 9600 baud Off = 4800 baud (factory sett

20、ing) ff = TCV lB, 01 = Set Cursor 1) The TCV and TC2100 systems use a 40-kHz carrier to transmit asynchronous ASCII serial data Test Procedures , Use a voltmeter to check the “Display” terminals (“RED” and “DLK” terminals): during normal operation, you should get a reading of 10 to 12 VDC. Within fi

21、ve seconds of being turned on, the display should show an initial message, such as “Vervvv DD,” where “Vvv” represents the software version number, and “DD” represents the DIP-switch setting. Note: The 5th and 6th bits of “DD” are “0” regardless of - the DIP-switch settings. Slide-Switch Settings for Display Addresses Display 1 2 Address 0 Off Off 1 On Off 2 Off On 3 j On j On 3 4 Off Off - Off Off Off Off ._ Off Off On Off On Off On Off _-_ On Off .-._ . Off On _ Off On Off On Off On On On -._. On On On On On On 2/95 Page 3 d i t . . , , -