LIPINSKI_L-609_Product_Manual 电路图.pdf

《LIPINSKI_L-609_Product_Manual 电路图.pdf》由会员分享，可在线阅读，更多相关《LIPINSKI_L-609_Product_Manual 电路图.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、 User Manual L-609 Preamplifier 500 series preamplifier module RadioFans.CN 收音机爱 好者资料库 2 PRECAUTIONS AND SAFETY CONSIDERATIONS We designed our product with maximum care in accordance with international safety standards. CAUTION Always follow the basic precautions listed below to avoid the possibilit

2、y of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Read setup instructions provided by us, Follow these instructions, Always insure that the preamplifier is properly grounded, Only use accessories manufa

3、ctured, specified or recommended by Lipinski, Do not use un-authorized main cables, All servicing must be performed by our qualified personnel, Do not expose this product to moisture, rain or water or direct sunlight, Insure adequate air circulation around your preamplifier, Power sources Connect th

4、is unit only to power sources specified in the Operating Instructions, and as marked on the unit, To avoid damage to your speakers and other playback equipment, turn off power to all related components before making any connections, Heat Do not use this unit near heat sources, including heating vent

5、s, stoves, or other appliances that generate heat. It should not be placed in temperatures less than 40F or higher than 95F. RadioFans.CN 收音机爱 好者资料库 Lipinski Sound Corporation| Confidential Copyright 2008 3 | P a g e CONTENTS 1. INTRODUCTION . 4 2. UNPACKING . 4 3. FEATURES . 5 4. FRONT PANEL DESCRI

6、PTION . 6 5. QUICK GUIDE TO USING THE L-609 PREAMPLIFIER . 7 6. MAIN BOARD VIEW . 8 7. PRODUCT SPECIFICATION . 8 8. LIPINSKI L-609 BLOCK DIAGRAM, SIGNAL PATH . 9 Lipinski Sound Corporation| Confidential Copyright 2010 4 | P a g e “Thank you for putting your trust with Lipinski. We understand how con

7、voluted the market place may be, and how difficult it is to come to a good decision in regard to sound quality. We appreciate your research and hope you enjoy your purchase.” Many Thanks, Lukas A. Lipinski Executive Director 1. INTRODUCTION You have selected Lipinski equipment which hails from thirt

8、y years of recording experience of Mr. Andrew Lipinski and his devotion to state-ofthe-art sound. To achieve this sound in the L-609 Pre-amplifier, we eliminated all capacitors and Integrated Circuits from the signal path and created our own, Lipinski Square patented discrete class A technology. We

9、also created transformer-like circuitry emulating an amorphous core transformer, albeit without unwanted, odd harmonic distortion. 2. UNPACKING Our product is carefully packed by us to maximize safety in transport. We advise that you unpack it on a soft, thick surface (carpet, fitted carpet, blanket

10、 etc) It helps to save all original packing materials and use them when you move the product. Lipinski Sound Corporation| Confidential Copyright 2010 5 | P a g e 3. FEATURES All discrete, class A patented circuitry No capacitors in the signal path No ICs in the signal path Microphone XLR or instrume

11、nt DI high impedance inch input Precision rotary gain control 8 position LED Peak / VU meter, switchable inside 48 Volt phantom power Resistor-less, -20dB PAD, which skips one stage of amplification to maintain signal quality Transformerless / Transformer input mode - proprietary circuit emulating a

12、morphous core transformer, eliminates unwanted distortion Minimal internal signal wiring Gain control is implemented in negative feedback loop, therefore it does not degrade dynamics Lipinski Sound Corporation| Confidential Copyright 2010 6 | P a g e 4. FRONT PANEL DESCRIPTION 1. 48V PHANTOM POWER T

13、his switch provides 48 Volts to power condenser microphones 2. PAD 20dB The PAD function provides 20dB attenuation of signal 3. MIC / GUITAR input selector The GUITAR switch enables high impedance instrument direct input 4. Transformer-less / Transformer- emulating (XFMR) microphone input 5. MIC / H

14、I-Z input selector Input socket used to plug microphone (XLR) or electric guitar (1/4 inch jack) 6. LED (Peak or VU) meter Diodes indicate output level 7. GAIN CONTROL The gain control adjusts the voltage gain from 38dB to 73dB When PAD switch is on, it adjusts the voltage gain from 18dB to 53dB Lip

15、inski Sound Corporation| Confidential Copyright 2010 7 | P a g e 5. QUICK GUIDE TO USING THE L-609 PREAMPLIFIER Mounting The L-609 Preamplifier requires a 500 Series rack. 1. First, turn off and unplug your rack frame. Make sure the slot you intend to use is clean and free of debris 2. Firmly and ev

16、enly push the L-609 Preamplifier into place until it is well situated in the card slot 3. Mount the L-609 front panel with two screws, to the 500 series rack Note: The screws are tight-fitting. Make sure to not cross the thread 4. Plug your 500 series rack back into the AC source, and power-up your

17、rack Set up 1. Turn the gain fully counter-clockwise and check that phantom power is off. 2. Using shielded, low capacitance microphone cable, connect a microphone to the preamplifier and then turn on the phantom power switch if required. When sending a signal to a recorder that has fixed input leve

18、ls, simply increase the gain until the optimum recording level is reached. 3. Careful! Turning the phantom power switch on or off, or the main power switch on or off can produce a large amplitude spike in the line output. Protect your ears, speakers, and equipment by being careful while the L-609 Pr

19、eamplifier output is connected to another piece of equipment. 4. Enjoy the sound of Lipinski. Lipinski Sound Corporation| Confidential Copyright 2010 8 | P a g e 6. MAIN BOARD VIEW Peak / VU switch: When VU meter is on, LED indicator on the front panel shows a subjective level of loudness. Otherwise

20、 instantaneous output level is measured. 7. PRODUCT SPECIFICATION Potentiometer gain range 35dB Minimum gain (with 20 dB Pad)18dB Maximum gain 73dB Dynamic range (curve A) 126dB Distortion (0 dB out) 0.008% Distortion (+12 dB out) 0.016% Maximum low distortion output+22dB Mic input impedance 6.8k DI

21、 input impedance 220k Power supply current 58mA Operating voltages +/-16V Lipinski Sound Corporation| Confidential Copyright 2010 9 | P a g e 8. LIPINSKI L-609 BLOCK DIAGRAM, SIGNAL PATH MIC IN MIC IN HI-Z IN 500 Series Rack XFMR PHANTOM PAD -20dB20dB0 - 35dB GAIN CONTROL Peak / VU LED Meter +48V OUT 500 Series Rack BALANCING CIRCUIT MIC / GUIT Lipinski Sound Corporation| Confidential Copyright 2010 10 | P a g e We wish you fantastic, unforgettable, moments of audio performance. The Lipinski Team