Neve 1272 Preamp 电路图.pdf

《Neve 1272 Preamp 电路图.pdf》由会员分享，可在线阅读，更多相关《Neve 1272 Preamp 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、Unbalanced to Balanced Line Converter Home Studio Recording DIY Projects Unbalanced to Balanced Line Converter This circuit will convert unbalanced audio lines to balanced audio lines. Heres the schematic diagram using NE5532 dual opamp chips, some resistors and capacitors. Tested the circuit on a b

2、readboard. It works! We all know that balanced lines have less susceptibility to noise, especially on long distances. This is common knowledge. But Id like to point out one more benefit of balanced signals that I just realized this afternoon. And that benefit is youll have 6db more gain in a balance

3、d signal compared with the original unbalanced signal! Mathematically, we know it would happen, but seeing it as a real waveform in Sonar is proof of Audio Recording Studio Learn Artist Management, Music Law, Media Distribution and More Online! www.FullSail.edu Digital Audio Workstation Optimized DA

4、W audio workstations from the quiet computing leader. Neve 1272 Preamp 1 of 29/30/11 10:29 AM RadioFans.CN 收音机爱 好者资料库 concept. Whats the big deal about 6db gain? 6db of gain is DOUBLE the signal strength. which means, your signal is going to be hotter, without any changes in your setup. Thus, you do

5、nt have to increase your preamp/mixers gain as much to achieve a good loud level, and since the signal increased by 6db, it also goes into saying that you just reduced your noise by 6db too, i.e. you also reduced noise by half. *My opinion speaking*. You see, MOST gear are really unbalanced inside.

6、They just have balanced drivers at the output stage. And some mastering engineers (read Bob Katzs book) prefer unbalanced gear ( yeah, I was shocked to hear this). His reasoning that since all the gear are plugged in one room anyway, and the inside circuitry of gear are almost always unbalanced, and

7、 depending on how the balanced circuit driver was made, could degrade the signal, etc. This guy knows electronics and his statement actually makes sense. But he also said that there are some truly balanced circuitry where you cant take away any part out, and these are almost always the best kind of

8、gear. (More on this below.) Back to the topic. the circuit above can be added to any unbalanced out and make it balanced. The 2 driver opamps drive each half of the signal, one being 180-degree inverted. In this case, the rejection of EMI and RFI is between the lines of the balanced input and output

9、 gears. not within the gear itself. If you can isolate the unbalanced-to-balanced driver circuit in a device and the device can still work, then that device is really unbalanced. The Neve preamp schematic on the other hand is a different beast. From the input transformer, all the way to the output t

10、ransformer, it is balanced. i.e. I cant take away the output transformer and still have this functioning right. I cant take away the input transformer and still have it functioning. The input and output transformer makes this gear have balanced inputs and outputs, and the supporting circuitry inside

11、 relies on connecting to these transformers to do its job. Note: The above circuit is an ACTIVE balanced driver. i.e. it requires power. There are other ways of achieving a balanced output and that is through the use of output transformers. See Jensen- website for their application notes. Of course,

12、 now were talking about spending $75 to $90 just for the cost of the transformer PER CHANNEL! Compare that to about less than $3.00 for the circuit above. Now you know why most manufacturers dont use audio transformers anymore, and the few ones that still use them sell gear in the $1,000+ range! Heres the frequency plot of my unbalanced to balanced coverter. Pretty good even though its sitting only on a breadboard. Neve 1272 Preamp 2 of 29/30/11 10:29 AM RadioFans.CN 收音机爱 好者资料库