Peavey NION Intergrators Manual V.03 电路图.pdf

《Peavey NION Intergrators Manual V.03 电路图.pdf》由会员分享，可在线阅读，更多相关《Peavey NION Intergrators Manual V.03 电路图.pdf（16页珍藏版）》请在收音机爱好者资料库上搜索。

1、NION Network Input Output Node v.03 System Integrators Manual RadioFans.CN 收音机爱 好者资料库 Page 2 copyright 2005 All Rights Reserved NION Integrators Manual Intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to c

2、onstitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not r

3、emove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this appliance, read the operating guide for further warnings. Este smbolo tiene el props

4、ito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin aislamiento den- tro de la caja del producto y que puede tener una magnitud suficiente como para constituir riesgo de descarga elctrica. Este smbolo tiene el propsito de alertar al usario de la presencia de instruccones importan

5、tes sobre la operacin y mantenimiento en la informacin que viene con el producto. PRECAUCION: Riesgo de descarga elctrica NO ABRIR! PRECAUCION: Para disminur el riesgo de descarga elctrica, no abra la cubierta. No hay piezas tiles dentro. Deje todo mantenimiento en manos del personal tcnico cualific

6、ado. ADVERTENCIA: Para evitar descargas elctricas o peligro de incendio, no deje expuesto a la lluvia o humedad este aparato Antes de usar este aparato, Iea ms advertencias en la gua de operacin. Ce symbole est utilis dans ce manuel pour indiquer lutilisateur la prsence dune tension dangereuse pouva

7、nt tre damplitude suffisante pour constituer un risque de choc lectrique. Ce symbole est utilis dans ce manuel pour indiquer lutilisateur quil ou quelle trouvera dimportantes instruc- tions concernant lutilisation et lentretien de lappareil dans le paragraphe signal. ATTENTION: Risques de choc lectr

8、ique NE PAS OUVRIR! ATTENTION: Afin de rduire le risque de choc lectrique, ne pas enlever le couvercle. Il ne se trouve lintrieur aucune pice pouvant tre repare par lutilisateur. Confiez Ientretien et la rparation de lappareil un rparateur Peavey agr. AVERTISSEMENT: Afin de prvenir les risques de dc

9、harge lectrique ou de feu, nexposez pas cet appareil la pluie ou lhumidit. Avant dutiliser cet appareil, lisez attentivement les avertissements supplmentaires de ce manuel. Dieses Symbol soll den Anwender vor unisolierten gefhrlichen Spannungen innerhalb des Gehuses warnen, die von Ausreichender Str

10、ke sind, um einen elektrischen Schlag verursachen zu knnen. Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. VORSICHT: Risiko Elektrischer Schlag! Nicht ffnen! VORSICHT: Um das Risiko eines ele

11、ktrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine Teile darin, die vom Anwender repariert werden knnten. Reparaturen nur von qualifiziertem Fachpersonal durchfhren lassen. ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gert nich

12、t dem Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. RadioFans.CN 收音机爱 好者资料库 Page 3MediaMatrix- A Division Of Peavey Electronics Corp. Safety Instructions IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions sho

13、uld always be followed, including the following: 1.Read these instructions. 2.Keep these instructions. 3.Heed all warnings. 4.Follow all instructions. 5.Do not use this apparatus near water. 6.Clean only with a dry cloth. 7.Do not block any of the ventilation openings. Install in accordance with man

14、ufacturers instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the o

15、ther. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.Protect the power cord from being walked on or pinch

16、ed, particularly at plugs, convenience receptacles, and the point they exit from the apparatus. 11.Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug proceed as follows: a) The wire that is colored green and yellow must be co

17、nnected to the terminal that is marked by the letter E the earth symbol colored green or colored green and yellow. b) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. c) The wire that is colored brown must be connected to the termin

18、al that is marked with the letter L or the color red. 12.Only use attachments/accessories provided by the manufacturer. 13.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

19、 combination to avoid injury from tip-over. 14.Unplug this apparatus during lightning storms or when unused for long periods of time. 15.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is dam

20、aged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 16.Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power supply of t

21、he type marked on the unit adjacent to the power supply cord. 17.If this product is to be mounted in an equipment rack, rear support should be provided. 18.Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise- induced he

22、aring loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Governments Occupational and Health Administration (OSHA) has specified the following permissible noise level exposures: Duration Per Day In HoursSound Level dBA, Slow Resp

23、onse 890 692 495 397 2100 1 1/2102 1105 1/2110 1/4 or less115 According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prev

24、ent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification

25、system be protected by hearing protectors while this unit is in operation. SAVE THESE INSTRUCTIONS! Page 4 copyright 2005 All Rights Reserved NION Integrators Manual To prevent electrical shock or potential fire hazards, do not expose this product to moisture or rain. Before using this product, read

26、 the user manuals for further warnings and cautions. The following cautions should be carefully observed when installing, wiring or using this product: DO NOT use any other power supply or cable other than the one provided with this unit. DO NOT remove the top cover of the unit. There are no user-se

27、rviceable parts inside. Refer service to qualified personnel. DO NOT use solvents or other cleaners to clean the unit. Basic external care requires only a damp cloth. Disconnect the power supply cord before cleaning. Read all safety and installation instructions and retain all documentation for furt

28、her refer- ence. This product should be installed so that its mounting position does not interfere with proper ventilation. Do not block air intake or exhaust vents. This product should not be installed or placed near a source of heat. Power supply cords and associated connectors should be unplugged

29、 from the power source when the unit is not used for long periods of time or stored. This product is designed for EIA rack mounting only. Use racks of sufficient depth and width to accommodate proper airflow and cable harnessing. Care should be taken to ensure that the installation is clear of possi

30、ble sources of contamina- tion. Make sure that the products ventilation openings are not exposed to possible sources of liquid, gases, or other contaminants. This product should be inspected by a qualified service technician if the power supply cord or connector has been damaged, if the unit has bee

31、n dropped, or if a foreign substance has gained access to the interior electronic and electrical components. The information contained in this manual is subject to change without notice. Peavey Electronics is not liable for improper installation or configuration. The information contained herein is

32、intended only as an aid to qualified personnel in the design, installation and maintenance of engineered audio sys- tems. The installing contractor or end user is ultimately responsible for the successful implementation of these systems. All creative content in this manual, including the layout, art

33、 design, content, photography, drawings, specifications and all other intellectual property is Copyright 2005 Peavey Electronics Corporation. All Rights Reserved. Features 12-bit analog converter precision. Digital Output: logic 0 Vout = 0.0v, Isink = 2mA; logic 1 Vout = 3.3v, Isource = 2mA. High Cu

34、rrent Outputs: 4 ports, each with a 0.5A self-resetting fuse and protection diodes for driving inductive loads. Vout = 11.5v nominal Isource = 0.5A. Direct short protection from ground to +36v. Relay Contacts: Form C contacts rated at 0.3A 125VAC or 110VDC, or 1A 30VDC. Mechanical Specifications Cha

35、ssis Style: 2RU EIA rack package Installation: EIA rack mount only Dimensions: 19 in. W x 16.8 in. D x 3.5 in. H Cooling: Forced air, front panel intake, rear and side panel exhaust. Page 15MediaMatrix- A Division Of Peavey Electronics Corp. Specifications Architects & Engineers Specifications Audio

36、 Processing Node The audio processing node shall be a 2RU industrial package designed for fixed installation in engineered audio and communications systems. The unit shall include an architecture based on an integrated floating-point DSP engine with at least 3 DSP chips. The DSP shall operate with a

37、 common digital audio bus with support for at least 512 simultaneous high-speed digital audio channels. The digital audio bus shall include an external expansion port that supports bus-level connectivity for additional units. Separate transmit and receive ports shall be provided for the digital audi

38、o bus. Software devices shall be included to allow the digital audio expansion ports to be easily integrated into the configuration file. The audio processing node shall include a software-based configuration and control. The DSP shall be completely configurable via a Windows-based software system,

39、with additional tools for creating user interface clients and integration with third-party control system included. Audio device algorithms shall support custom I/O, control and signal flow design and shall be integrated within the design environment for intuitive system configuration. This software

40、 shall include an XML architecture and support for standard Ethernet management, including, but not limited to SNMP shall be standard from an integrated, rear-panel LAN port. The audio processing node shall include an embedded Linux operating system. The operating system shall reside on non-mechanic

41、al IDE storage media. The storage system shall include support for reading/writing data from the operating system, configuration software or the front panel. Audio file support, including but not limited to, .wav audio shall be standard and shall be completely integrated with the units software tool

42、s. A Compact Flash device of at least 256M shall be used as the primary storage media and operating system root. The audio processing node shall include a modular I/O card bay system for support individual 8-channel audio cards. Cards shall be available for mic and line level analog audio with optio

43、ns for digital and proprietary audio transports. The audio node shall include a modular CobraNet audio transport module with support for at least 64 20-bit digital audio channels. Separate software devices shall be provided for integrating CobraNet audio I/O into the configuration file. The audio pr

44、ocessing node shall include support for serial data transport including a front panel RS-232 and rear panel RS-485 port. All data transports, including Ethernet, shall be available simultaneously and shall include separate software devices for integration into the configuration file. The audio proce

45、ssing node shall include an integrated GPIO breakout system with at least 16 configurable logic ports and 4 configurable high-current ports. All GPIO ports shall include software devices for integrating their function into the configuration file. The GPIO connections shall be externally terminated w

46、ith a DIN-rail breakout assembly. The audio processing node shall include a front panel interface with LCD display. Navigation of the display shall include a rotary data wheel with push switch and at least four context-sensitive soft buttons. Dual color status LEDs shall be included on the front pan

47、el for monitoring network status, storage and power conditions. The audio processing node shall be fan cooled with a front-panel exhaust and shall operate with a universal computer-grade modular power supply. The audio processing node shall be the MediaMatrix NION n6 or n3 or approved equal. MediaMatrix A Division of Peavey Electronics Corp. 711 A St., Meridian Mississippi, 39301 601-483-9548 Features & Specifications subject to change without notice Copyright 2005, All Rights Reserved Printed in the USA 04/2005 80303100