Shure M60 Preamp 电路图.pdf

《Shure M60 Preamp 电路图.pdf》由会员分享，可在线阅读，更多相关《Shure M60 Preamp 电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、222 HARTREY AYE EVANSTON, ILL ? CABLE SHUREMlCRO MICROPHONES AND ELECTRONIC COMPONENTSDATA SHEET MODEL M60 EVANSTON PHONE DA-8-9000 CHICAGO PHONE SH 3-1600 Stereo Preamplifier STEREO PREAMPLIFIER GENERAL:T h e S h u r e M 6 0 S t e r e o P r e a m p l i f i e r i s a h i g h quality, flat amplifier

2、designed primarily to allow the phono cart- ridge to be used at a distance from the control preamplifier. The M60 preamplifier matches the impedance of the phono cartridge and has dual input and dual low impedance outputs so that up to 50 (15.2 m) feet of cable (30MMFD per foot) can be used between

3、the M60 preamplifier and the main control center with no noticeable deviation in the entire audio frequency response. The M60 has 17db gain (per channel) to overcome any losses in signal transmission.The additional gain by use of the preamplifier, also, reduces the hum and noise very often present i

4、n certain high fidelity systems. The M60 preamplifier has a chrome plated chassis that fits under most turntables and record changers. It is shock mounted to reduce microphonics and acoustic feedback. The preamplifier has its own power supply and is equipped with an ON-OFF switch. The M60 Stereo Pre

5、amplifier can be used as a general purpose flat amplifier having a gain of 17db per channel (stereo) or 34db gain (monaural) with microphones, headsets, test equipment, etc. Output voltages of approximately 2 volts RMS are obtainable before a 10% harmonic distortion of waveform is noted. SPECIFICATI

6、ONS: Gain:17db per channel5 millivolts input produces 35 milli- volts output. Frequency Response:1db from 30 to 80,000 c.p.s. Equalization: None. Input Impedances: 47,000 ohms. Output Impedances: 5,000 ohms. Hum and Noise Level: 64db below rated output. Distortion:Less than 0.14%.1000 c.p.s. at rate

7、d output. Separation Between Channels: 30db. Channel Balance: 1 db. Tubes: One dual function ECC83/12AX7. Rectifier: Selenium-Full wave rectification for minimum ripple Power Requirements:117 volts 60 c.p.s. 4 watts. Finish: Chrome plate. Overall Dimensions:Length 6-9/16 (166.7 mm); Width 2 (57.2 mm

8、); Height 3-3/8 (85.7 mm). Copyright 1960, Shure Brothers. Inc. 27A159 (7-60) INSTALLATION: The M60 Stereo Preamplifier may be mounted under most turntables or record changers. Rubber insola- tion mounts are provided to reduce microphonics and acoustic feedback. Figure A shows how the rubber shock m

9、ounts are in- stalled. Machine or self-tapping screws can be used through the 4 corner mounting holes in the preamplifier base. F I G . A For minimum hum pickup and best operating conditions, the preamplifier should be placed as far away from the turntable motor as conveniently possible. Printed in

10、U.S.A. RadioFans.CN 收音机爱 好者资料库 CONNECTIONS:The internal wiring connections are shown in Figure B. To place the M60 preamplifier in operation as a two channel stereo preamplifier, connect the signal leads from the cartridge into the channel A and B (phone jacks marked “IN”). The output of the preampl

11、ifier (phono jacks marked “OUT”) should be connected to the main control preamplifier of the stereo system. Attention must be given to all of the information contained in the cartridge or phono arm data sheets regarding phasing, grounding, etc. If it is found necessary to “ground” the M60 preamplifi

12、er chassis, a wire can be connected to one of the screws holding the bottom plate on to the chassis. Capacitance in Microfarads Resistance in Ohms Resistors - 1/2 Watt, 10% except R5 & R6, 5% Voltages shown should be measured to chassis ground using VTVM. FIG. B If the full 17db gain is not required

13、, lower output voltages and lower impedances are possible with the use of a simple resistor net- work at the output of the preamplifier. This circuit change is shown in Figure C for a 1/3 or a 2/3 reduction in amplifier output. CAUTION: The electrical plug should be removed from the power outlet bef

14、ore the chassis is opened or any changes are made. For 1/3 Reduction (2/3 output) Replace each 5600 ohm Resistor (R3 and R4) with two Resist- ors (R3a and R3b, R4a and R4b) having the following values: R3a and R4a-3900 ohms, watt, 10%. R3b and R4b-1800 ohms, watt, 10%. For 2/3 Reduction (1/3 output)

15、 Replace each 5600 ohm Resistor (R3 and R4) with two Resist- ors (R3a and R3b, R4a and R4b) having the following values: R3a and R4a-1800 ohms, watt, 10%. R3b and R4b-3900 ohms, watt, 10%. GUARANTEE:This Shure High Fidelity Component is guar- anteed to be free from electrical and mechanical defects

16、for a period of 90 days from date of shipment from the factory, provided all instructions are complied with fully. In case of damage, it is essential that you carefully repack the unit and return it to the factory for repair. Our guarantee is voided if the basic assembly has been opened or subjected to unreasonably rough handling. RadioFans.CN 收音机爱 好者资料库