Aiwa-HSJS385-tape-sm 电路图 维修手册.pdf
《Aiwa-HSJS385-tape-sm 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Aiwa-HSJS385-tape-sm 电路图 维修手册.pdf(20页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL YH YJ YL YZ YU HS-JS385 HS-JS385W STEREO RADIO CASSETTE RECORDER BASIC TAPE MECHANISM : 7ZM-5 R3N S/M Code No. 09-989-302-6FP REVISION Rivision A4size.p659/24/98, 7:51 PM1 RadioFans.CN 收音机爱 好者资料库 DESCRIPTIONREF. NO.KANRI NO. PART NO.KANRI NO. REF. NO.DESCRIPTIONPART NO. SPECIFICATIONS
2、 Frequency rangeYJ,YH,YL,YZ: AM: 530 1605 kHz FM: 87.5 108 MHz YU: AM: 530 1710 kHz FM: 87.5 108 MHz Maximum output20 mW + 20 mW (EIAJ/16W) 15 mW + 15 mW (EIAJ/32W) Power sourceBattery DC 3V, R6 (size AA) X 2 YJ,YH,YL,YU: Domestic AC power (using the optional AC adaptor: AIWA AC 620 / AC 302) YZ: Do
3、mestic AC power (using the optional AC adaptor: AIWA AC 300 / AC 302) SpeakerDiameter 36 mm, YJ,YH,YL,YU: 4W x 2 YZ: 6W x 2 Design and specifications are subject to change without notice. 2 ACCESSORIES / PACKAGE LIST 188-HJ7-906-010 - IB,D (J)-IN 188-HJ7-903-010IB,Y (ESF)-I 188-HJ7-904-010IB,Y (GID)
4、-I 188-HJ7-905-010IB,Y (POHCZ)-I 188-HJ7-902-010IB,YJ (ESC)-I 188-HJ7-908-010IB,YL (ESP)-IN 188-HJ7-901-010IB,YU (ESF)-I 287-B30-139-010 - HEADPHONE,HP-M007(TL) 287-B30-081-010HEADPHONE,HP-M009(S) 387-041-083-110 1F CM-S40A 488-HJ7-951-010 - CASE,CARRYING (NEW) Battery lifeEIAJ, 1 mW output, playbac
5、k Approx. 5 hours using R6P (sizeAA) manganese batteries Approx. 22 hours using LR6 (size AA) alkaline batteries EIAJ, 10 mW output, playback Approx. 3 hours using R6P (size AA) manganese batteries Approx. 10 hours using LR6 (size AA) alkaline batteries EIAJ, recording Approx. 3.5 hours using R6P (s
6、ize AA) manganese batteries Approx. 13 hours using LR6 (size AA) alkaline batteries Maximum dimensions (W x H x D)115.4 x 90.7 x 38.5 mm (45/8 x 35/8x 19/16 inches) WeightApprox. 205 g (7 oz) (excluding batteries) Rivision A4size.p6524-Sep-98, 10:57 AM2 RadioFans.CN 收音机爱 好者资料库 DISASSEMBLY INSTRUCTIO
7、NS 3 REMOVAL OF REAR CABINET 1.Remove one screw on the Rear Cabinet. 2.Open the lid, battery. 3.Push in the direction of the white bold arrows to release all the catches. 4.With the gap generated from the above step, slip in your finger to remove the Rear Cabinet over the KNOB, RTRY TUN in the direc
8、tion of the black arrow A . 5.Remove the Rear Cabinet in the direction of black arrow B . * A FLEX is soldered onto the board on the Rear Cabinet, during disassembly, be careful not to damage this FLEX. REMOVAL OF THE MAIN C.B. 1.Remove 3 screws of the MAIN C.B. 2.Desolder the Tape Head FLEX and mot
9、or wires. 3.Disconnect the connector CON101. 4.Remove the MAIN C.B in the direction of the arrow. REMOVAL OF MECHANISM 1.Remove 2 screws of the HLDR, BAT. 2.Remove the mechanism in the direction of the bold arrow. * During assembly of mechanism, be sure that connector CON101 emerge out at the bottom
10、 as shown and the Direction change switch and pause switch are engaged. * CON101 Rear Cabinet Battery Lid KNOB, RTRY TUN A B Desolder Tape Head FLEX Desolder Motor Wires Disconnect CON101 TO FRONT C.B MAIN C.B Tape Head FLEX * Direction change switch * Pause switch HLDR, BAT Rivision A4size.p659/24/
11、98, 7:42 PM3 RadioFans.CN 收音机爱 好者资料库 4 REMOVAL OF THE FRONT C.B. 1.Remove 2 screws on the FRONT C.B. 2.Release the 2 hooks and slide the FRONT C.B out of the slots in the direction of the arrow. REMOVAL OF THE BUILT-IN MIC 1.Remove 4 screws of the WINDOW, TUN. 2.Release the catches of the WINDOW, TU
12、N by pushing in the directions of white arrows. 3.Remove the WINDOW, TUN in the black arrow direction. 4.Remove 2 screws of the COVER, MIC. 5.Remove the COVER, MIC. 6.Remove the CUSHION, MIC. 7.Remove the NET, MIC and the HLDR, MIC and the BUILT-IN, MIC can be removed. FRONT C.B COVER, MIC CUSHION,
13、MIC MIC HLDR, MIC NET, MIC Ensure stress free wires Release Hook Slots FRONT C.B FROM MAIN C.B Rivision A4size.p6524-Sep-98, 10:58 AM4 5 HOW TO REPLACE THE BUILT-IN MIC 1.As shown illustration, the MIC has two solder points. One point A is linked to the MIC CHASSIS and the other point B is not. Sold
14、er the GND wire (Black) to point A and the MIC wire (Brown) to point B . 2.Place the MIC and CUSHION, MIC into the HLDR, MIC make sure they are properly seated into the NET, MIC before reassembling. 3.Arrange the MIC wires as shown so that it will not cause any obstructions. REASSEMBLY OF MAIN BOARD
15、 1.Slot in the MAIN C.B in the direction of the bold arrow. 2.Arrange the connector wires out through the hole and confirm that it does not obstruct the KNOB, RTRY TUN and batteries insertion. 3.Arrange the motor wires such that it does not obstruct SFR 51 and batteries insertion. 4.Confirm that pau
16、se switch is seated into the LEVER ASSY, DIR. MIC CHASSIS MIC Wire GND Wire Back view of the MIC MIC Wire KNOB, RTRY TUN BAT, CONTACT (+) Connector Wires SFR 51 Motor Wires Pause Switch A B FRONT C.B FROM MAIN C.B TO FRONT C.B MAIN C.B Rivision A4size.p6524-Sep-98, 10:58 AM5 6 HOW TO REASSEMBE THE P
17、OINTER TUN, GEAR TUN AND KNOB RTRY TUN. 1.Slot in the POINTER, TUN until point A . 2.With the larger center holes diameter of the GEAR, TUN facing down, insert it into point B followed by point C . 3.Before mounting of KNOB, RTRY TUN confirm POINTER, TUN is fully at point A and turn the TUN-CAP full
18、y, counter-clockwise. 4.Mount the KNOB, RTRY TUN and secure with the screw. 5.TUN KNOB, RTRY TUN to clockwise to confirm POINTER, TUN is able to move to point D . Turn TUN-CAP fully KNOB, RTRY TUN GEAR, TUN POINTER, TUN A D CB Rivision A4size.p6524-Sep-98, 10:58 AM6 7 IC BLOCK DIAGRAM - 1 Rivision A
19、4size.p6524-Sep-98, 10:58 AM8 DESCRIPTIONREF. NO.KANRI NO. PART NO.KANRI NO. REF. NO.DESCRIPTIONPART NO. ELECTRCAL MAIN PARTS LIST IC 87-001-943-080 1F IC,TA8155F 87-A20-532-040 1D IC,LB1977M 87-A20-851-040 1C C-IC,TA2111F 87-017-643-080 1B IC,MM1206XF 87-002-232-080 1C IC,NJM2073M 87-001-371-080 1C
20、 IC,LA4533M 87-A20-968-040 - C-IC,AN 7322S TRANSISTOR 89-502-094-040 - C-FET,2SK209Y 87-026-261-080 0E C-TR,RN1404 87-026-225-080 1A FET,2SJ106GR 87-026-263-080 0E C-TR,RN1410 87-A30-060-080 - C-TR,KTC3875GR 87-A30-159-080 0E C-TR,KTA1298Y 87-A30-061-080 - C-TR,KTA1504GR 89-112-134-040 - TR,2SA1213Y
21、 87-026-235-080 0E C-TR,DTC114EK 89-333-266-080 0E CHIP TR,2SC3326B DIODE 87-020-027-080 0E CHIP-DIODE 1SS184 87-020-339-080 0E CHIP DIODE,1SS226 MAIN C.B 88-HJ7-616-010 - FF-CABLE, 10P BPF10187-008-406-080BPF GFMB1 BPF10181-HW1-628-080 1B CHIP BAND PASE FILTER C187-010-180-080 0E C-CAP,S 1500P-50 B
22、K C187-010-178-080CHIP CAP 1000P C287-010-180-080 0E C-CAP,S 1500P-50 BK C287-010-178-080CHIP CAP 1000P C387-016-462-080 0E C-CAP,S 1-16 F C487-016-462-080 0E C-CAP,S 1-16 F C587-010-322-080 0E C-CAP,S 100P-50 CH C687-010-322-080 0E C-CAP,S 100P-50 CH C787-010-177-080 0E C-CAP,S 820P-50 SL C887-010-
23、177-080 0E C-CAP,S 820P-50 SL C987-010-426-080 0E C-CAP,S 0.012-25 K B C987-010-191-080CAP, CHIP 0.015 ZF C1087-010-426-080 0E C-CAP,S 0.012-25 K B C1087-010-191-080CAP, CHIP 0.015 ZF C1187-A10-418-080 0E C-CAP,TN 22-4 A TCF C1287-A10-418-080 0E C-CAP,TN 22-4 A TCF C1387-010-194-080 0E CAP, CHIP 0.0
24、47 C1487-010-194-080 0E CAP, CHIP 0.047 C1587-016-462-080 0E C-CAP,S 1-16 F C1687-016-462-080 0E C-CAP,S 1-16 F C1787-016-462-080 0E C-CAP,S 1-16 F C1887-016-462-080 0E C-CAP,S 1-16 F C2087-012-140-080 0E CAP 470P C2187-010-178-080 0E CHIP CAP 1000P C2287-A10-584-080 1A C-CAP,TN 100-4V C2387-A10-422
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Aiwa-HSJS385-tape-sm 电路图 维修手册 Aiwa HSJS385 tape sm 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


