Aiwa-CXJPK331-cs-sm 电路图 维修手册.pdf

《Aiwa-CXJPK331-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CXJPK331-cs-sm 电路图 维修手册.pdf（80页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COMPACT DISC DECK RECEIVER E Model SPECIFICATIONS CX-JN331/JPK331 Ver. 1.0 2005.05 Model Name Using Similar MechanismCX-JN33/JPK33 CD CD Mechanism TypeCDM74KS-F1BD81C Section Base Unit NameBU-F1BD81C Optical Pick-up NameKSM-215DCP Tape deck Model Name Using Similar MechanismCX-JN33/JP

2、K33 Tape Transport Mechanism Type CWM43FF13 (JPK331) Section CWM43FR34 (JN331) 9-879-731-01 2005E05-1 2005.05 Sony Corporation Personal Audio Group Published by Sony Engineering Corporation Continued on next page CX-JN331 is the amplifier, CD player, tape deck and tuner section in JAX-N331. CX-JPK33

3、1 is the amplifier, CD player, tape deck and tuner section in JAX-PK331. CX-JN331 The following measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 48 + 48 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 60 + 60 watts (6 ohms at 1 kHz, 10% THD) CX-JPK331 The

4、following measured at AC 120, 127, 220, 240 V 50/60 Hz DIN power output (rated): 48 + 48 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 60 + 60 watts (6 ohms at 1 kHz, 10% THD) Inputs VIDEO/MD IN (phono jacks): voltage 450/250 mV, impedance 47 kilohms MIC (phone jack) chilean

5、and peruvian model sensitivity 1 mV, impedance 10 kilohms Amplifier section Outputs PHONES (stereo mini jack): accepts headphones of 8 ohms or more SPEAKER:accepts impedance of 6 to 16 ohms CD player section SystemCompact disc and digital audio system Laser Diode PropertiesEmission duration: continu

6、ous Laser Output: Less than 44.6 W (This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture) Frequency response2 Hz 20 kHz (0.5 dB) Signal-to-noise ratioMore than 90 dB Dynamic rangeMore than 90 dB Tape deck section

7、 Recording system4-track 2-channel, stereo Frequency response50 13,000 Hz (3 dB), using Sony TYPE I cassettes Wow and flutter0.15% W. Peak (IEC) 0.1% W. RMS (NAB) 0.2% W. Peak (DIN) AM tuner section Tuning range 2 Band type: Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tunin

8、g range87.5 108.0 MHz (50-kHz step) AntennaFM lead antenna Antenna terminals75 ohms unbalanced Intermediate frequency10.7 MHz 530 1,710 kHz (with the tuning interval set at 10 kHz) 531 1,602 kHz (with the tuning interval set at 9 kHz) AntennaAM loop antenna Antenna terminalsExternal antenna terminal

9、 Intermediate frequency450 kHz RadioFans.CN 收音机爱 好者资料库 2 CX-JN331/JPK331 General Power requirements Mexican models:127 V AC, 60 Hz Other models:120 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector 110 watts Dimensions (w/h/d) incl. projecting parts and controls Amplifier/Tuner/Tap

10、e/CD section: Approx. 280 325 425 mm Power consumption Mass Approx. 8.3 kg Design and specifications are subject to change without notice. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexibl

11、e Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. This appliance is classified

12、as a CLASS 1 LASER product. This label is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE W

13、ITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. RadioFans.CN 收音机爱 好者资料库 3 CX-JN331/JPK331 TABLE OF CONTENTS 1.SERVICING NOTES.4 2

14、.GENERAL.7 3.DISASSEMBLY 3-1.Disassembly Flow .9 3-2.Case (Side-L/R) . 10 3-3.Case (Top) . 10 3-4.Tray Panel. 11 3-5.CD Mechanism Deck (CDM74KS-F1BD81C). 11 3-6.Front Pack Block . 12 3-7.Back Panel Section . 12 3-8.MAIN Board. 13 3-9.Tape Mechanism Deck (CWM43FF13: JPK331)/(CWM43FR34: JN331) . 13 3-

15、10. Table Assy . 14 3-11 MOTOR (TB) Board . 14 3-12 MOTOR (LD) Board . 15 3-13 Base Unit (BU-F1BD81C) . 15 3-14 Motor Gear Assy (Sled) (M102), CD BOARD . 16 3-15 Optical Pick-up (KSM-215DCP) . 16 4.TEST MODE. 17 5.MECHANICAL ADJUSTMENTS. 21 6.ELECTRICAL ADJUSTMENTS. 21 7.DIAGRAMS 7-1.Block Diagram S

16、ERVO Section . 24 7-2.Block Diagram MAIN Section . 25 7-3.Block Diagram PANEL/POWER SUPPLY Section . 26 7-4.Printed Wiring Board CD Board . 28 7-5.Schematic Diagram CD Board . 29 7-6.Printed Wiring Boards CHANGER Section . 30 7-7.Schematic Diagram CHANGER Section . 31 7-8.Printed Wiring Board CDMP3

17、CONNECT Board . 32 7-9.Schematic Diagram CDMP3 CONNECT Board . 33 7-10. Schematic Diagram MAIN Section (1/4) . 34 7-11. Schematic Diagram MAIN Section (2/4) . 35 7-12. Schematic Diagram MAIN Section (3/4) . 36 7-13. Schematic Diagram MAIN Section (4/4) . 37 7-14. Printed Wiring Boards MAIN Section .

18、 38 7-15. Printed Wiring Boards PANEL Section . 39 7-16. Schematic Diagram PANEL Section (1/2) . 40 7-17. Schematic Diagram PANEL Section (2/2) . 41 7-18. Printed Wiring Board POWER AMP Section . 42 7-19. Schematic Diagram POWER AMP Section . 43 7-20. Printed Wiring Boards TRANS Section . 44 7-21. S

19、chematic Diagram TRANS Section . 45 8.EXPLODED VIEWS 8-1.Case Section . 56 8-2.Tape Mechanism Deck Section (CWM43FF13: JPK331)/(CWM43FR34: JN331). 57 8-3.Panel Board Section . 58 8-4.Cassette Box Section . 59 8-5.Front Panel Section . 60 8-6.Back Panel Section . 61 8-7.Chassis Section. 62 8-8.CD Mec

20、hanism deck Section-1 (CDM74KS-F1BD81C) . 63 8-9.CD Mechanism deck Section-2 (CDM74KS-F1BD81C) . 64 8-10. CD Mechanism deck Section-3 (CDM74KS-F1BD81C) . 65 8-11. Base Unit (BU-F1BD81C) . 66 9.ELECTRICAL PARTS LIST. 67 RadioFans.CN 收音机爱 好者资料库 4 CX-JN331/JPK331 The laser diode in the optical pick-up

21、block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair pa

22、rts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode

23、 emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times. SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOC

24、K OR BASE UNIT UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder h

25、as the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to abou

26、t 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usab

27、le with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. MODELPART No. CX-JPK331: Mexican model4-252-231-2 CX-JN331/JPK331: Chilean and Peruvian models4-252-231-3 MODEL IDENTIFICATION + + RLRL Rear View PART No. 5 CX-JN331/JPK331 HOW TO

28、 OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF. SERVICE POSITION CD MECHANISM DECK CD mechanism deck stand CDMP3 CONNECT board 1Remove the case (side-L). 2Turn the loading gear in the direction of arrow A. A 3Pull-out the disc tray. 6 CX-JN331/JPK331 FRONT PANEL SECTION AMP BOARD MAIN board PANEL b

29、oard front panel section tape mechanism deck SUB TRANS board TRANS board AMP board MAIN board front panel section 7 CX-JN331/JPK331 SECTION 2 GENERAL This section is extracted from instruction manual. LOCATION OF CONTROLS Main unit ALBUM + wk ALBUM wk BASS control 5 CD qh CD SYNC qs Deck A 9 Deck B

30、wl DISC 1 3 wd DISC SKIP/EX-CHANGE wf Operation Dial (AMS/TUNING) qf ?/1 (power) 1 ALPHABETICAL ORDER A NO Z BUTTON DESCRIPTIONS + + + + + + + + ZZ wd wf wg wh wk 4qjqhqk qlw;waws wj 1 qg qf qd qs 0 qa 9 2 8 356 7 wl e; Disc tray ws DISPLAY qg Display window 4 ENTER 2 i-Bass qd MIC jack2)e; MIC LEVE

31、L2)e; MIDDLE control 5 P FILE 6 PHONES jack qa PLAY MODE w; PRESET EQ 3 REC PAUSE/START 8 Remote sensor 7 SURROUND wa TAPE A/B qk TREBLE control 5 TUNER/BAND qj TUNING MODE w; VIDEO/MD ql VOLUME control wh Z PUSH (deck A) (eject) 0 Z (eject) wg PUSH Z (deck B) (eject) wj m (rewind) wk x (stop) wk H

32、or hH1) (play) wk X (pause) wk M (fast forward) wk 1) CX-JN331 only 2) CX-JPK331 chilean and peruvian model only 8 CX-JN331/JPK331 Remote control ALBUM + qa ALBUM qd CD qk CLEAR qg CLOCK/TIMER SELECT 2 FM MODE 4 FUNCTION 6 PLAY MODE w; REPEAT 4 SLEEP ws TAPE qj TUNER BAND 5 TUNER MEMORY ql TUNING MO

33、DE w; VOLUME +/ qs ?/1 (power) 1 m/M (rewind/fast forward) 7 N (play) 8 X (pause) 8 x (stop) 8 /+ (tuning) qh ./ (go back/go forward) qh ALPHABETICAL ORDER A EF Z BUTTON DESCRIPTIONS 4 5 6 7 8 9 q; ws1 qd qg qf wa w; ql qk qj qh qa qs 3 2 CLOCK/TIMER SET 3 DISC SKIP 0 DISPLAY wa ENTER 9 EQ qf CX-JN3

34、31/JPK331 9 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISASSEMBLY SET 3-2.CASE (SIDE-L/R) (Page 10) 3-3.CASE (TOP) (Page 10) 3-4.TRAY PANEL (Page 11) 3-6.FRONT PANEL BLOCK (Page 12) 3-7.BACK PANEL SECTION (Page 12) 3-9.TAPE MECHANISM DECK (CWM43FF13: JPK33

35、1)/ (CWM43FR34: JN331) (Page 13) 3-8.MAIN BOARD (Page 13) 3-14. MOTOR GEAR ASSY (SLED) (M102), CD BOARD (Page 16) 3-15. OPTICAL PICK-UP (KSM-215DCP) (Page 16) 3-13. BASE UNIT (BU-F1BD81C) (Page 15) 3-10. TABLE ASSY (Page 14) 3-11. MOTOR (TB) BOARD (Page 14) 3-12. MOTOR (LD) BOARD (Page 15) 3-5.CD ME

36、CHANISM DECK (CDM74KS-F1BD81C) (Page 11) Note 1:The process described in can be performed in any order. Note 2:Without completing the process described in , the next process can not be performed. CX-JN331/JPK331 10 3-3.CASE (TOP) Note: Follow the disassembly procedure in the numerical order given. 3

37、-2.CASE (SIDE-L/R) 3case (top) 2three claws 1two screws (BVTP3 10) 4case (side-L) 7case (side-R) 6two screws (BVTP3 10) 3two screws (BVTP3 10) 1two screws (case 3 TP2) 5three screws (case 3 TP2) 2screw (case 3 TP2) CX-JN331/JPK331 11 3-4.TRAY PANEL 3-5.CD MECHANISM DECK (CDM74KS-F1BD81C) 1Turn the l

38、oading gear in the direction of arrow A. A four claws 3Remove the tray panel in the direction of arrow C. C 2Pull-out the tray in the direction of arrow B. B 7CD mechanism deck (CDM74KS-F1BD81C) 2screw (BVTP3 10) 3three screws (BVTP3 10) 1screw (BVTP3 10) 5wire (flat type) (17 core) (CN873) 6two con

39、nectors (CN701, CN874) 4 CX-JN331/JPK331 12 3-7.BACK PANEL SECTION 3-6.FRONT PANEL BLOCK 3screw (BVTP3 8) 4harness 6front panel block 5three screws (BVTP3 8) 2connector (CN112) 2connector (CN324) 1wire (flat type) (29 core) (CN302) 2connector (CN309) 2connector (CN103) 3two screws (BVTP3 10) 1wire (

40、flat type) (15 core) (CN101) 2two connectors (CN904, 906) 2connector (CN901) 4duct cover 9back panel section 5three screws (BVTP3 10) 6two screws (BVTP3 8) 8SUB TRANS board 7two screws (BVTP3 10) CX-JN331/JPK331 13 3-8.MAIN BOARD 3-9.TAPE MECHANISM DECK (CWM43FF13: JPK331)/ (CWM43FR34: JN331) 3conne

41、ctor (CN307) 2two screws (BVTP3 8) 1connector (CN907)4MAIN board 1six screws (BVTP2.6 8) 2tape mechanism deck (CWM43FF13: JPK331)/ (CWM43FR34: JN331) CX-JN331/JPK331 14 3-10. TABLE ASSY 3-11. MOTOR (TB) BOARD 3wire (flat type) (5 core) (CN702) 4hook 1Turn the loading gear in the direction of arrow A

42、. A 5two claws 2Pull-out the table assy. 6table assy 2tray 4connector (CN731) 1screw (PTPWH M2.6) 5two screws (BTTP M2.6) 6MOTOR (TB) board 3belt (table) CX-JN331/JPK331 15 3-12. MOTOR (LD) BOARD 3-13. BASE UNIT (BU-F1BD81C) 2connector (CN704) 3two screws (BTTP M2.6) 4MOTOR (LD) board 1belt (loading

43、) 3four coil springs (insulator) 1wire (flat type) (27 core) (CN201) 2four floating screws (PTPWHM2.6) 4four insulators 5base unit (BU-F1BD81C) CX-JN331/JPK331 16 3-14. MOTOR GEAR ASSY (SLED) (M102), CD BOARD 3-15. OPTICAL PICK-UP (KSM-215DCP) 1Remove two solders. qaCD board 2two screws (P2 3) 6claw 7gear (A) 8