Aiwa-CXJN5-cs-sm 电路图 维修手册.pdf

《Aiwa-CXJN5-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CXJN5-cs-sm 电路图 维修手册.pdf（78页珍藏版）》请在收音机爱好者资料库上搜索。

1、Model Name Using Similar MechanismNEW CD Mechanism Type CDM74-K6BD71A, CDM74S-K6BD71A, CDM74S-K6BD72 CD Base Unit NameBU-K6BD71A, BU-K6BD72 Section Optical Block NameKSM-213DCP Optical Pick-up NameKSS-213D Tape deck Model Name Using Similar MechanismNEW Section Tape Transport Mechanism Type CWM43FF1

2、3, CWM43FR16, CWM43FR26 Ver 1.1 2003.06 9-877-250-02Sony Corporation 2003F05-1Home Audio Company 2003.06Published by Sony Engineering Corporation SPECIFICATIONS CX-JN5 is the amplifier, CD player, tape deck and tuner section in JAX-N5/PK5. Continued on next page RadioFans.CN 收音机爱 好者资料库 CX-JN5 Notes

3、on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- ing repairing. Do not touch the soldering iron on the sa

4、me conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure. SAFETY-RELATED COMPONE

5、NT WARNING! COMPONENTS IDENTIFIED BY MARKOR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. The following caution la

6、bel is located inside the unit. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: C

7、heck the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return t

8、o chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Pr

9、ecision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples

10、 of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR L

11、A SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. RadioFans.CN 收音机爱 好者资料库 CX-JN5 TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL Location of Controls .7 3.DISASSEMBLY 3-1.Disassembly Flow

12、 .9 3-2.Case (SIDE-L/R). 10 3-3.Case (Top) . 10 3-4.Tray Panel. 11 3-5.CD Mechanism Deck (CDM74-K6BD71AS, CDM74S-K6BD71A, CDM74S-K6BD72). 11 3-6.Front Panel Section . 12 3-7.Mechanical Deck (CWM43FF13, CWM43FR16, CWM43FR26) . 12 3-8.Rear Cabinet Section . 13 3-9.PT Board, MAIN Board. 13 3-10. Table

13、Assy . 14 3-11. Motor (TB) Board . 14 3-12. Motor (LD) Board. 15 3-13. Base Unit (BU-K6BD71A, BU-K6BD72) . 15 3-14. Motor Gear Assy (Sled) (M701), BD Board . 16 3-15. Optical Pick-up (KSS-213D). 16 4.TEST MODE. 17 5.ELECTRICAL ADJUSTMENTS CD Section . 19 6.DIAGRAMS 6-1.Block Diagram CD Section . 20

14、6-2.Block Diagram TUNER/TAPE/PANEL Section . 21 6-3.Block Diagram AMP/POWER SUPPLY Section . 22 6-4.Note for Printed Wiring Boards and Schematic Diagrams . 23 6-5.Printed Wiring Board BD Section (AEP, UK, CIS, E51, MX). 24 6-6.Schematic Diagram BD Section (AEP, UK, CIS, E51, MX). 25 6-7.Printed Wiri

15、ng Board BD Section (US, CND, E, SP, TW, KR, AUS). 26 6-8.Schematic Diagram BD Section (US, CND, E, SP, TW, KR, AUS). 27 6-9.Printed Wiring Boards CHANGER Section . 28 6-10. Schematic Diagram CHANGER Section . 29 6-11. Schematic Diagram MAIN Section (1/4) . 30 6-12. Schematic Diagram MAIN Section (2

16、/4) . 31 6-13. Schematic Diagram MAIN Section (3/4) . 32 6-14. Schematic Diagram MAIN Section (4/4) . 33 6-15. Printed Wiring Board MAIN Section . 34 6-16. Printed Wiring Board HP Section . 35 6-17. Schematic Diagram HP Section . 35 6-18. Printed Wiring Board PANEL Section . 36 6-19. Schematic Diagr

17、am PANEL Section . 37 6-20. Printed Wiring Boards KEY Section . 38 6-21. Schematic Diagram KEY Section . 39 6-22. Printed Wiring Board PT Section (Except E, E51, SP, TW). 40 6-23. Schematic Diagram PT Section (Except E, E51, SP, TW). 41 6-24. Printed Wiring Board PT Section (E, E51, SP, TW) . 42 6-2

18、5. Schematic Diagram PT Section (E, E51, SP, TW) . 43 6-26. IC Pin Function Description . 47 7.EXPLODED VIEWS 7-1.Case Section . 49 7-2.Front Panel Section-1. 50 7-3.Front Panel Section-2. 51 7-4.Front Panel Section-3. 52 7-5.Front Panel Section-4. 53 7-6.Chassis Section . 54 7-7.CD Mechanism Deck S

19、ection-1 (CDM74-K6BD71AS, CDM74S-K6BD71A, CDM74S-K6BD72). 55 7-8.CD Mechanism Deck Section-2 (CDM74-K6BD71AS, CDM74S-K6BD71A, CDM74S-K6BD72). 56 7-9.CD Mechanism Deck Section-3 (CDM74-K6BD71A, CDM74S-K6BD71A, CDM74S-K6BD72). 57 7-10. Base Unit Section (BU-K6BD71A, BU-K6BD72). 58 8.ELECTRICAL PARTS L

20、IST. 59 Abbreviation AUS : Australian model CND : Canadian model E51: Chilean and Peruvian models KR: Korean model MX: Mexican model SP: Singapore model TW: Taiwan model RadioFans.CN 收音机爱 好者资料库 CX-JN5 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode

21、in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is

22、included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when

23、checking the laser diode emis- sion, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times. MODEL IDENTIFICATION Back Panel MODELPART

24、No. US model4-245-154-0 Chilean and Peruvian models4-245-154-2 CIS model4-245-154-4 E, Singapore and Taiwan models4-245-154-6 Korean and Australian models4-245-154-8 AEP and UK models4-245-280-0 Mexican model (made in Mexico)4-245-280-3 Mexican model (made in China)4-245-280-4 Canadian model4-245-28

25、0-5 PART No. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has

26、 the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about

27、350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges oc- cur such as on IC pins, etc. Usab

28、le with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. CX-JN5 HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF. Pull-out the disc tray. Remove the case (side-L). Turn the loading gear in the direction of arrow . CX-JN5 SERVICE PO

29、SITION CD mechanism deck Tape mechanism deck main board (CN691) Connect wire (flat type) (19 core) to main board (CN691) and BD board (CN710). BD board (CN710) Connect wire (flat type) (13 core) to panel board (CN601) and mechanical deck. panel board (CN601) main board (CN301) CX-JN5 SECTION 2 GENER

30、ALThis section is extracted from instruction manual. DISC CHANGE POWER STANDBY/ON MODE ENTER TREBLE DIR(TAPE B)/PRESET STOP/CLEAR TUNING DOWN, TUNING UP PAUSE/SET BASS i-Bass DISPLAY ALBUM , (AEP, UK, CIS, Chilean, Peruvian and Mexican models) MULTI JOG PHONES jack SYNC DUB REC/REC MUTING DISC DIREC

31、T PLAY 1-3 OPEN/CLOSE TAPE A/B TUNER/BAND VIDEO/AUX CD Remote sensor VOLUME En AM LOOP, FM 75 terminals VIDEO/AUX jacks VIDEO AUXTV SPEAKER terminals AC voltage selector (E, Chilean, Peruvian, Singapore, Taiwan) AC power cord LOCATION OF CONTROLS CX-JN5 En POWER 1-0/10, +10 EDIT BAND TAPE A/B SPECTR

32、UM TUNER MODE , ALBUM , PLAY MODE REPEAT ENTER CLOCK/TIMER/SET CLOCK/TIMER/SELECT DISPLAY SHIFT FUNCTION DISC SKIP / , SLEEP VOLUME ( ,) SOUND CLEAR KARAOKE ALBUM , En CLOCK SET AM 12:00PM 12:00 - -:- - CX-JN5 This set can be disassembled in the order shown below. 3-1.DISASSEMBLY FLOW SECTION 3 DISA

33、SSEMBLY CX-JN5 3-3.CASE (TOP) Note: Follow the disassembly procedure in the numerical order given. 3-2.CASE (SIDE-L/R) CX-JN5 3-4.TRAY PANEL 3-5.CD MECHANISM DECK (CDM74-K6BD71AS, CDM74S-K6BD71A, CDM74S-K6BD72) CX-JN5 3-6.FRONT PANEL SECTION 3-7.MECHANICAL DECK (CWM43FF13, CWM43FR16, CWM43FR26) CX-J

34、N5 3-8.REAR CABINET SECTION 3-9.PT BOARD, MAIN BOARD CX-JN5 3-10. TABLE ASSY 3-11. MOTOR (TB) BOARD CX-JN5 3-12. MOTOR (LD) BOARD 3-13. BASE UNIT (BU-K6BD71A, BU-K6BD72) CX-JN5 3-14. MOTOR GEAR ASSY (SLED) (M701), BD BOARD 3-15. OPTICAL PICK-UP (KSS-213D) CX-JN5 SECTION 4 TEST MODE MC COLD RESET The

35、 cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1.In the standby status, while pressing thebutton, press the button. 2.The set is reset, then becomes standby status. GC TEST MODE Procedure

36、: 1.Press the button to turn the power on. 2.While pressing thebutton, press the button for 5 seconds. 3.It change displays in order of model type, version and suffix at 2 seconds interval, then the display is back to normal status. AMP TEST MODE Procedure: 1.In the status where AC plug is disconnec

37、ted, while pressing thebutton, connect the AC plug to turn the power on. Then enter the AMP test mode and display “AMP TEST”. 2.If turn the knob clockwise, it displays “VOLUME MAX”, and if turn the knob counterclockwise, it displays “VOLUME 0”. 3.If the andknobs are turned clockwise or counterclockw

38、ise, it change displays in order of “EQ MAX”, “EQ MIN” and “EQ FLAT”. 4.To release from this mode, disconnect the AC plug and turn the power off. DISC TRAY LOCK Procedure: 1.Press the button to turn the power on. 2.While pressing thebutton, press the button for 5 seconds. 3.The message “LOCKED” is d

39、isplayed and the tray is locked. (Even if exiting from this mode, the tray is still locked) 4.To release this lock, while pressing thebutton, press the button for 5 again. 5.The message “UNLOCKED” is displayed and the tray is un- locked. CD REPEAT 5 LIMIT CANCEL MODE Number of repeat for CD playback

40、 is 5 times when the repeat mode is “REPEAT”. This mode enables CD to repeat playback for limitless times. Procedure: 1.Press the button to turn the power on. 2.In the repeat on status, while pressing thebutton, press the button to enter the CD repeat 5 limit cancel mode and repeat mark blinks on th

41、e fluorescent indicator tube. 3.To release this mode, press the button to turn the power off. CHANGE-OVER OF AM TUNER STEP BETWEEN 9 kHz AND 10 kHz (Except AEP, UK and CIS models) A step of AM channels can be changed over between 9 kHz and 10 kHz. Procedure: 1.Press the button to turn the power on.

42、2.While pressing the button, press the but- ton to the display on fluorescent indicator tube changes to “AM 530 kHz” (10 kHz step) or “AM 531 kHz” (9 kHz step), and thus the channel step is changed over. FUNCTION CHANGE MODE Select either TV, VIDEO or AUX (MD) of the external function input. Procedure: 1.Press the button to turn the power on. 2.While pressing the button, press the button. 3.Each time this operation is operated, it change disp