Aiwa-HV-FX5100-Service-Manual(1) 电路图 维修手册.pdf

《Aiwa-HV-FX5100-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-HV-FX5100-Service-Manual(1) 电路图 维修手册.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。

1、BASIC TAPE MECHANISM : OVD-6VIDEO CASSETTE RECORDER HV-FX5100 S/M Code No. 09-996-332-2N1 K SERVICE MANUAL DATA 230 V AC, 50 Hz 17W 3.5 kg (7.7 lbs.) 380 mm (W) x 267 mm (D) x 95 mm (H) (15 x 10 5/8 x 3 3/4 in.) 5C to 40C Rotary 2 head helical scanning system PAL colour system, 625 lines, 50 fields

2、Double azimuth 4 heads VHS video cassette UHF: 21 to 69 UHF channels between 23 and 69, 73 dB 240 lines (SP) 30 minutes Frequency synthesized tuner I 135 seconds with E-180 tape 108 seconds with E-180 tape 20 Hz-20 KHz More than 75 dB SPECIFICATIONS Less than 0.01% (nominal) PAL SP: 23.39 mm/sec LP:

3、 11.69 mm/sec NTSC (playback only) SP: 33.35 mm/sec PAL SP: 5 hours with E-300 tape LP: 10 hours with E-300 tape NTSC (playback only) SP: 3 hours 30 minutes with T-210 tape 1.0 Vp-p, 75 ohm, unbalanced 1.0 Vp-p, 75 ohm, unbalanced 53 dB (nominal) SCART: 3.8 dBs, 50 Kohm RCA: 3.8 dBs, 50 Kohm SCART:

4、3.8 dBs, less than 1 Kohm RCA: 3.8 dBs, less than 1 Kohm 3 tracks (Hi-Fi sound 2 tracks, Normal sound 1 track) HI-FI WOW AND FLUTTER. TAPE SPEED . RECORDING/PLAYBACK TIME . VIDEO INPUT. VIDEO OUTPUT . VIDEO S/N . AUDIO INPUT . AUDIO OUTPUT . AUDIO TRACK . POWER REQUIREMENTS. POWER CONSUMPTION. WEIGH

5、T . DIMENSIONS . OPERATING TEMPERATURE. VIDEO RECORDING SYSTEM . VIDEO SIGNAL SYSTEM . VIDEO HEAD . USABLE CASSETTES. CHANNEL COVERAGE. RF OUTPUT . HORIZONTAL RESOLUTION . TIMER BACKUP . TUNER SYSTEM . TV SYSTEM . FAST-FORWARD TIME. REWIND TIME . HI-FI FREQUENCY RESPONSE . HI-FI DYNAMIC RANGE . Desi

6、gn and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 TABLE OF CONTENTS SPECIFICATIONS . TABLE OF CONTENTS . SERVICING NOTICES ON CHECKING . IMPORTANT NOTICE . DISASSEMBLY INSTRUCTIONS REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS . REMOVAL OF DECK PARTS. KEY TO ABBREVIAT

7、IONS . SERVICE MODE LIST . PREVENTIVE CHECKS AND SERVICE INTERVALS . NOTE FOR THE REPLACING OF MEMORY IC . SERVICING FIXTURES AND TOOLS . PREPARATION FOR SERVICING . VCR TEST TAPE INTERCHANGEABILITY TABLE . MECHANICAL ADJUSTMENTS CONFIRMATION AND ADJUSTMENT. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNI

8、NG MECHANISM . MECHANISM ADJUSTMENT PARTS LOCATION GUIDE . ELECTRICAL ADJUSTMENTS BASIC ADJUSTMENTS . ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE. TROUBLESHOOTING GUIDES. IC DESCRIPTIONS . SERVO TIMING CHART . SYSTEM SWITCH MODE . SEMICONDUCTOR BASE CONNECTIONS . BLOCK DIAGRAMS Y/C/AUDIO/HEAD AMP . S

9、YSTEM CONTROL/SERVO/TIMER . TUNER/HIFI/21PIN/OSD/VPS/NICAM . OPERATION/POWER. DECK SCHEMATIC DIAGRAM. OPERATION SCHEMATIC DIAGRAM . PRINTED CIRCUIT BOARDS (OPERATION 1/2/DECK) . PRINTED CIRCUIT BOARDS (SYSCON) . Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM . SYSTEM CONTROL/SERVO/TIMER SCHEMATIC DIAGRAM . 21

10、PIN/OSD/VPS SCHEMATIC DIAGRAM . TUNER/HIFI SCHEMATIC DIAGRAM . POWER SCHEMATIC DIAGRAM . DISPLAY SCHEMATIC DIAGRAM . NICAM SCHEMATIC DIAGRAM . INTERCONNECTION DIAGRAM. WAVEFORMS . MECHANICAL EXPLODED VIEW . MECHANICAL REPLACEMENT PARTS LIST . ACCESSORY REPLACEMENT PARTS LIST . CHASSIS EXPLODED VIEW

11、(TOP VIEW). CHASSIS EXPLODED VIEW (BOTTOM VIEW). CHASSIS REPLACEMENT PARTS LIST . ELECTRICAL REPLACEMENT PARTS LIST . A-1 COVER A-1 A-2 A-2 B1-1 B2-1B2-5 C1-1, C1-2 C2-1 C3-1, C3-2 C4-1 C5-1 C5-1 C6-1 D1-1, D1-2 D1-2, D1-3 D1-4 D2-1 D2-2 E-1E-28 F-1, F-2 G-1 G-2 H-1 I-1 I-2 I-3 I-4 J-1 J-2 J-3 J-4J-

12、6 J-7 J-8 J-9 J-10 J-11 J-12 J-13 J-14 K-1 L1-1 L2-1 L2-1 M1-1 M1-2 M2-1 N-1N-3 RadioFans.CN 收音机爱 好者资料库 SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep

13、the indications and notices in the operation manual. 2. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to

14、 the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used. 3. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING There are parts which use the insulation material such as a tube or tape for safety

15、, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions. PERFORM A SAFETY CHECK AFTER SERVICING 4. Confirm that the

16、screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And

17、 be sure the safety of that. IMPORTANT NOTICE The remote control for this model can be selected the Custom code 1 and Custom code 2. How to selection; Custom code 1 : P Custom code 2 : Press the Power key and 1 key on the remote control simultaneously for more than 2 seconds. Press the Power key and

18、 2 key on the remote control simultaneously for more than 2 seconds. The Custom code 1 is only available for the VCR unit but the Custom code 2. When selected the Custom code 2 by mistake, just remove the batteries from the remote control for the moment or select the Custom code 1 as described above

19、. A-2 RadioFans.CN 收音机爱 好者资料库 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS 1-1: TOP CABINET, FRONT CABINET AND OPERATION 1, 2 PCB (Refer to Fig. 1-1) 1. 2. 3. 4. 5. 6. 7. Remove the 4 screws 1. Remove the Top Cabinet in the direction of arrow (A). Disconnect the following

20、connectors: (CP651 and CP652). Unlock the 7 supports 2. Remove the Front Cabinet in the direction of arrow (B). Remove the 3 screws 3 and remove the Operation 1 PCB. Remove the 4 screws 4 and remove the Operation 2 PCB. Fig. 1-1 1 Top Cabinet 1-2: FLAP (Refer to Fig. 1-2) 1. 2. Open Flap to 90 and f

21、lex in direction of arrow (A), at the same time slide in direction of arrow (B). Then lift in direction of arrow (C). (A) (C) (B) Flap Fig. 1-2 1 1 1 (A) 2 2 2 2 Operation 1 PCB 3 3 3 (B) 2 2 2 4 4 4 4 Operation 2 PCB Front Cabinet 1-3: DECK CHASSIS (Refer to Fig. 1-3) Remove the 3 screws 1. Remove

22、the screw 2. Disconnect the following connectors: (CP1001, CP1002, CP1004, CP4001, CP4002 and CP4003). Remove the Deck Chassis in the direction of arrow. 1. 2. 3. 4. Bottom Plate 1 1 12 Deck Chassis Fig. 1-3 1-4: SYSCON PCB (Refer to Fig. 1-4) Syscon PCB Bottom Plate 1 Remove the screw 1. Remove the

23、 2 screws 2. Remove the 2 screws 3. Remove the Syscon PCB in the direction of arrow. 1. 2. 3. 4. Fig. 1-4 3 3 22 B1-1 DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DECK PARTS 2-1: TOP BRACKET (Refer to Fig. 2-1) Remove the 2 screws 1. Slide the 2 supports 2 and remove the Top Bracket. 1. 2. NOTE When you i

24、nstall the Top Bracket, install the screw (1) first, then install the screw (2). 1 (2) Top Bracket Top Bracket Main Chassis Main Chassis 2 1 (1) 2 Fig. 2-1 2-2: NOTE When you install the Tape Guide L, install as shown in the circle of Fig. 2-3-B. (Refer to Fig. 2-3-B) REC Lever Tape Guide L The REC

25、Lever is not installed on the Video Cassette Player. Fig. 2-3-B 2-4: CASSETTE HOLDER ASSY (Refer to Fig. 2-4) Move the Cassette Holder Assy to the front side. Push the Locker R to remove the Cassette Side R. Remove the Cassette Side L. 1. 2. 3. Main Chassis Main Chassis Cassette Side L Cassette Side

26、 R Locker R Fig. 2-4 2-5: CASSETTE SIDE L/R (Refer to Fig. 2-5) Remove the Locker Spring. Unlock the 4 supports 1 and then remove the Cassette Side L/R. 1. 2. NOTE When you install the Cassette Side L/R, be sure to move the Locker L/R after installing. Locker Spring Cassette Side L Cassette Side R 1

27、 1 1 Locker L Locker R1 Fig. 2-5 Screw Torque: 5 0.5kgfcm DECK COVER/FLAP LEVER/TAPE GUIDE R (Refer to Fig. 2-2) Move the Cassette Holder Assy to the back side. Unlock the support 1 and remove the Deck Cover. Remove the Polyslider Washer 2. Unlock the support 3 and remove the Flap Lever. Unlock the 3 supports 4 and remove the Tape Guide R. 1. 2. 3. 4. 5. Fig. 2-2 2-3: TAPE GUIDE L (Refer to Fig. 2-3-A) Move the Cassette Holder Assy to the back side. Unlock the 2 supports 1 and remove the Tape Guide L. Remove the REC Lev