Aiwa-NSXSZ20-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXSZ20-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXSZ20-cs-sm 电路图 维修手册.pdf（33页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA COMPACT DISC STEREO SYSTEM BASIC TAPE MECHANISM : ZZM-3 PR1NM BASIC CD MECHANISM : AZG-1 ZD3RDM NSX-DR1 NSX-SZ20 EZ V S/M Code No. 09-007-423-4R4 REVISION This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-DR1(EZ), (S/M Code No. 09-004-423-4T4). If

2、requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M Code No. 09-001-335-3N8). NSX-DR1 SPEAKERSYSTEM CD CASSEIVER REMOTE CONTROLLER NSX-SZ20 CX-NDR1SX-NSZ20 CX-NSZ20SX-NSZ22 RC-ZAS02 RadioFans.CN 收音机爱 好者资料库 2 SPECIFICATIONS Tuning rangeEZ: 87.5 MHz to 108 MHz V: FM1 (OIRT)

3、 65 MHz to 74 MHz (10 kHz step) FM2 (CCIR) 87.5 MHz to 108 MHz (50 kHz step) Usable sensitivity (IHF)EZ: 16.8 dBf V: FM1: 15.3 dBf FM2: 12.8 dBf Antenna terminals75 ohms (unbalanced) Tuning range531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) Usable sensitivity350 V/m AntennaLoop

4、antenna Tuning range144 kHz to 290 kHz Usable sensitivity1400 V/m AntennaLoop antenna Power outputRated: 30 W + 30 W (6 ohms, THD 1%, 1 kHz/DIN 45500) Reference: 35 W + 35 W (6 ohms, THD 10%,1 kHz/DIN 45324) DIN MUSIC POWER : 67 W + 67 W Total harmonic distortion 0.08% (15 W, 1 kHz, 6 ohms, DIN AUDI

5、O) InputsVIDEO/AUX: 500 mV OutputsSPEAKERS: accept speakers of 6 ohms or more PHONES (stereo jack): accepts headphones of 32 ohms or more Track format4 tracks, 2 channels stereo Frequency response50 Hz 15 kHz Recording systemAC bias HeadsDeck 1: Playback head x 1 Deck 2: Recording/Playback head x 1,

6、 erase head x 1 LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Power requirements230 V AC, 50 Hz Power consumption80 W Power consumption in standby mode 14 W With power-economizing mode off 0.9 W With power

7、-economizing mode on Dimensions of main unit260 x 328 x 335 mm (W x H x D) Weight of main unit6.2 kg Speaker System3 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 140 mm cone type Tweeter: 60mm cone type Super tweeter: 20 mm ceramic type Impedance6 ohms Output sound pressure level 8

8、7 dB/W/m Dimensions (W x H x D)230 x 324x 256 mm Weight3.8 kg Design and specifications are subject to change without notice. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN

9、 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A

10、 DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. TCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. TAdvarsel: Usynlig laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for str

11、ling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saataa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning,

12、som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herin may result in hazardous radiation exposure. ATTENTION Lutillisation de commandes, rglages ou procdures aut

13、res que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on

14、the rear exterior. Precaution to replace Optical block (KSS-213F) 1) After the connection, remove solder shown in the right figure. Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

15、 Solder (KSS 213F) PICKUP Assy P.C.B. RadioFans.CN 收音机爱 好者资料库 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor ( ) 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors ca

16、n change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MIC

17、ROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned

18、on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD te

19、rminal to “L”. Good or no good judgement of the MICROCOMPUTER 1Turn on the AC main power. 2Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working c

20、orrectly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102

21、) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 1Remove the AC power cord. 2Connect a discharging resistor at an en

22、d of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 3Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 4Contact the same end of the discharging resistor as step 3 to the negative (-) side (-VH)

23、 of C102 in the same way. (For two seconds) 5Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table. MAIN C.B D101 C101C102 34 22 - 4 - In such a case, check also if the POWER AMPLIFIE

24、R circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. W

25、hen the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord. 2Short bot

26、h ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and el

27、ectrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described pr

28、ocedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 18 15 C113 18 15 Short with tweezers. - 5 - 6 ELECTRICAL MAIN PARTS LIST DESCR

29、IPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 87-A21-397-010 IC,STK490-070 87-A21-419-040 IC,NJM14558MD-TE2 87-A21-401-040 C-IC,M61503FP 87-A21-269-010 IC,EW732 87-A21-560-010 IC,LA1844L-A 8A-NF9-601-110 C-IC,UPD780226GF-014-3BA 8A-NF9-604-010 C-IC,UPD780226GF-015-3BA 87-A

30、21-482-010 IC,RPM6938-H4 87-070-127-110 IC,LC72131 D TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-074-080 C-TR,RT1P 141C 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 8

31、7-026-235-080 CHIP-TR,DTC114EK 87-A30-087-080 C-FET,2SK2158 87-A30-091-080 FET,2SJ460 87-A30-090-080 FET,2SK2541 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-318-080 TR,CSA952K 87-A30-329-080 TR,CD1585BC 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-072-080 C-TR,RT1P 144C 87-A30-234-080 TR,CSC4115BC 87-A30-468

32、-080 C-TR,KRC102S-RTK 87-A30-086-040 C-TR,CSD1306E 89-503-602-080 C-FET 2SK360E 87-A30-062-080 C-TR,KRC104S DIODE 87-A40-553-080 DIODE,1N4003 LES 87-A40-776-080 ZENER,UZ27BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A4

33、0-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-020-465-080 DIODE,1SS133 87-A40-854-080 ZENER,UZ15BSA MAIN C.B C3 87-012-368-080 C-CAP,S 0.1-50 F C4 87-012-368-080 C-CAP,S 0.1-50 F C5 87-012-368-080 C-CAP,S 0.1-50 F C6 87-012-368-080 C-CAP,S 0.1-50 F C9 87-012-

34、368-080 C-CAP,S 0.1-50 F C10 87-012-368-080 C-CAP,S 0.1-50 F C11 87-012-368-080 C-CAP,S 0.1-50 F C12 87-012-368-080 C-CAP,S 0.1-50 F C19 87-A10-627-000 CAP,E 2200-50 SMG C20 87-A10-627-000 CAP,E 2200-50 SMG C21 87-A10-520-000 CAP,E 3300-35 M SMG C22 87-A10-520-000 CAP,E 3300-35 M SMG C25 87-010-385-

35、080 CAP, ELECT 220-25V C26 87-010-247-080 CAP, ELECT 100-50V C30 87-010-430-080 CAP, ELECT 100-63 C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01-25 K B C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-380-080 CAP, ELECT 47-16V M 11L C36 87-010-381-080 CAP, ELECT 330-16V C38

36、87-010-197-080 CAP, CHIP 0.01-25 K B C60 87-010-403-080 CAP, ELECT 3.3-50V C61 87-010-260-080 CAP, ELECT 47-25V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C99 87-010-196-080 CHIP CAPACITOR,0.1-25 C101 87-010-185-080 C-CAP,S 3900P-50 B C102 87-010-185-080 C-CAP,S 3900P-50 B C103 87-010-545-080 CAP, ELE

37、CT 0.22-50V SME C104 87-010-545-080 CAP, ELECT 0.22-50V SME C105 87-010-187-080 CHIP CAP 5600P-50 K B C106 87-010-187-080 CHIP CAP 5600P-50 K B C107 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C109 87-010-179-080 C-CAP,S 1200P-50 KB C110 87-010-179-080 C-CAP,S 1200P-50 K

38、B C111 87-010-391-080 CAP,E 10-35 SME C112 87-010-391-080 CAP,E 10-35 SME C113 87-010-405-080 CAP, ELECT 10-50V C114 87-010-405-080 CAP, ELECT 10-50V C119 87-010-197-080 C-CAP,S 0.01-25 K B C120 87-010-197-080 C-CAP,S 0.01-25 K B C123 87-010-176-080 C-CAP,S 680P-50 J SL C124 87-010-176-080 C-CAP,S 6

39、80P-50 J SL C125 87-012-368-080 C-CAP,S 0.1-50 F C126 87-012-368-080 C-CAP,S 0.1-50 F C127 87-012-368-080 C-CAP,S 0.1-50 F C128 87-012-368-080 C-CAP,S 0.1-50 F C129 87-010-191-080 C-CAP,S 0.015-50 F C130 87-010-191-080 C-CAP,S 0.015-50 F C131 87-010-197-080 CAP, CHIP 0.01-25 K B C132 87-010-197-080

40、CAP, CHIP 0.01-25 K B C133 87-010-186-080 CAP,CHIP 4700P-50 K C140 87-010-182-080 C-CAP,S 2200P-50 B C141 87-010-196-080 CHIP CAPACITOR,0.1-25 C183 87-010-387-080 CAP, ELECT 470-25 M C184 87-010-403-080 CAP, ELECT 3.3-50 M C185 87-A11-148-080 CAP, TC U 0.1-50 ZF C239 87-010-196-080 CHIP CAPACITOR,0.

41、1-25 C301 87-010-178-080 C-CAP,S 1000-50 K B C302 87-010-178-080 C-CAP,S 1000-50 K B C303 87-010-178-080 C-CAP,S 1000-50 K B C304 87-010-178-080 C-CAP,S 1000-50 K B C307 87-010-263-080 CAP, ELECT 100-10V C308 87-010-263-080 CAP, ELECT 100-10V C309 87-010-318-080 C-CAP,S 47P-50 CH C310 87-010-318-080

42、 C-CAP,S 47P-50 CH C313 87-010-188-080 CAP,CHIP 6800P-50 K C314 87-010-188-080 CAP,CHIP 6800P-50 K C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V C326 87-010-198-080 CAP, CHIP 0.022-25 K C327 87-012-368-080 C-CAP,S 0.1-50 F C360

43、 87-010-401-080 CAP, ELECT 1-50V C399 87-012-140-080 C-CAP,S 470P-50 J C401 87-010-544-080 CAP, ELECT 0.1-50V C402 87-010-544-080 CAP, ELECT 0.1-50V C403 87-010-321-080 CHIP CAPACITOR,82P(J) C404 87-010-321-080 CHIP CAPACITOR,82P(J) C405 87-010-197-080 CAP, CHIP 0.01-25 K B C406 87-010-197-080 CAP,

44、CHIP 0.01-25 K B C407 87-010-197-080 CAP, CHIP 0.01-25 K B C408 87-010-197-080 CAP, CHIP 0.01-25 K B C409 87-010-182-080 C-CAP,S 2200P-50 B C410 87-010-182-080 C-CAP,S 2200P-50 B C411 87-010-405-080 CAP, ELECT 10-50V C412 87-010-405-080 CAP, ELECT 10-50V 7 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRI

45、PTIONREF. NO.KANRI NO. PART NO. C452 87-010-382-080 CAP, ELECT 22-25V C453 87-010-183-080 C-CAP,S 2700P-50 B C454 87-010-183-080 C-CAP,S 2700P-50 B C455 87-010-183-080 C-CAP,S 2700P-50 B C456 87-010-197-080 CAP, CHIP 0.01-25 K B C460 87-010-196-080 CHIP CAPACITOR,0.1-25 C461 87-012-158-080 C-CAP,S 3

46、90P-50 CH C462 87-012-158-080 C-CAP,S 390P-50 CH C458 87-010-178-080 C-CAP,S 1000-50 K B C459 87-010-175-080 C-CAP,S 560P-50 J SL C605 87-010-179-080 CAP,CHIP S 1200P-50 K C606 87-010-179-080 CAP,CHIP S 1200P-50 K C609 87-010-213-080 C-CAP,S 0.015-50 B C610 87-010-213-080 C-CAP,S 0.015-50 B C611 87-

47、010-545-080 CAP, ELECT 0.22-50V C612 87-010-545-080 CAP, ELECT 0.22-50V C613 87-010-545-080 CAP, ELECT 0.22-50V C614 87-010-545-080 CAP, ELECT 0.22-50V C615 87-010-154-080 CAP CHIP 10P-50 CH C616 87-010-221-080 CAP, ELECT 470-10V SME C617 87-010-221-080 CAP, ELECT 470-10V SME C618 87-010-405-080 CAP, ELECT 10-50V C630 87-016-669-080 C-CAP,S 0.1-25 K B C631 87-010-185-080 C-CAP,S 3900P-50 B C632 87-010-185-080 C-CAP,S 3900P-50 B C633 87-016-369-080 C-CAP,S 0.033-25 K B C634 87-016-369-080 C-CAP,S 0.033-25 K B C669 87-010-322-080 C-CA