Aiwa-NSXSZ52-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXSZ52-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXSZ52-cs-sm 电路图 维修手册.pdf（36页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA NSXSZ50RCZAS01 SYSTEM CD CASSEIVER REMOTE CONTROLLER CXNSZ50 COMPACT DISC/ STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM(HA) BASIC TAPE MECHANISM : 6ZM-3 PR2NM(K/EZ) BASIC CD MECHANISM : AZG-1 YZD8RDM(K) BASIC CD MECHANISM : AZG-1 ZD8RDM(EZ/HA) NSX-SZ50 NSX-SZ52

2、EZ,K,HA EZ S/M Code No. 09-004-424-6R4 REVISION This Service Manual is the Revision Publishing and replaces Simple Manual NSX-SZ50 & NSX-SZ52 (S/M Code No. 09-002-424-6T2). If requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M Code No. 09-001-335-3N6). SPEAKER SXWNSZ50 N

3、SXSZ52CXNSZ52 SXWNSZ52RCZAS01 RadioFans.CN 收音机爱 好者资料库 2 Main unit CX-NSZ50, CX-NSZ52 FM tuner section Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)16.8 dBf 13.2 dBf Antenna terminal75 ohms (unbalanced) AM (MW) tuner section Tuning range531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz

4、(10 kHz step) Usable sensitivity350 V/m AntennaLoop antenna LW tuner section Tuning range144 kHz to 290 kHz Usable sensitivity1400 V/m AntennaLoop antenna Amplifier section Mid-high frequency amplifier Power outputRated: 20 W + 20 W (8 ohms, T.H.D. 1 %, 1 kHz/DIN 45500) Reference : 25 W + 25 W (8 oh

5、ms, T.H.D. 10 %, 1 kHz/DIN 45324) DIN MUSIC POWER: 40 W + 40 W Total harmonic distortion0.1 % (10 W, 1 kHz, 8 ohms, DIN AUDIO) Low frequency amplifier Power outputRated: 60 W + 60 W (6 ohms, T.H.D. 1 %, 130 Hz/DIN 45500) Reference : 75 W + 75 W (6 ohms, T.H.D. 10 %, 130 Hz/DIN 45324) DIN MUSIC POWER

6、: 130 W + 130 W Total harmonic distortion0.1 % (30W, 130 Hz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV MIC: 1.0 mV (10 k ohms) OutputsSPEAKERS HIGH FREQ: accept speakers of 8 ohms or more SPEAKERS LOW FREQ: accept speakers of 6 ohms or more SURROUND SPEAKERS: accept speakers of 8 ohms to 16 ohms PH

7、ONES (stereo jack): accepts headphones of 32 ohms or more SPECIFICATIONS Cassette deck section Track format4 tracks, 2 channels stereo Frequency response50 Hz 15000 Hz Recording systemAC bias HeadsDeck 1: Playback head x 1 Deck 2: Recording/playback head x 1, erase head x 1 Compact disc player secti

8、on LaserSemiconductor laser ( = 780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Wow and flutterUnmeasurable General Power requirements230 V AC, 50 Hz 120 V/220-230 V/240 V AC switchable, 50/60 Hz Power consumption150 W 130 W Power cons

9、umption in standby mode If the power-economizing mode is ECO OFF: 20 W If the power-economizing mode is ECO ON or ECO AUTO: 0.9 W Dimensions of main unit260 x 326 x 345 mm (W x H x D) Weight of main unit9.0 kg Speaker system SX-WNSZ50, SX-WNSZ52 Speaker system3 way, Built-in subwoofer (magnetic shie

10、lded type) Speaker unitsSubwoofer: 160 mm cone type Full range: 100 mm cone type Super tweeter: 20 mm ceramic type Impedance6 ohms/8 ohms Sensitvity87 dB/W/m Dimensions (W x H x D)240 x 324 x 271 mm Weight4.8 kg REF. NOPART NO.KANRIDESCRIPTION NO. ACCESSORIES LIST 1 8A-NF8-902-010 IB,LH(ESP)M 1 8A-N

11、F8-905-010 IB,K(E)E 1 8A-NF8-926-010 IB,EZ(9L)M 1 8A-NF8-936-010 IB,EZ(9L)M- RDS 2 8Z-NF8-702-010 RC UNIT,RC-ZAS01 Design and specifications are subject to change without notice. The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE Sound, Inc. REF. NOPART NO.K

12、ANRIDESCRIPTION NO. 3 87-006-225-010 ANT,LOOP ANT NC2 4 87-043-115-010 FEEDER-ANT,FM 4 87-A90-118-010 ANT,WIRE FM(Z) RadioFans.CN 收音机爱 好者资料库 3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainit- ulla tavalla saattaa altistaa kyt-tjn tu

13、rvallisuusluokan 1 ylit- tvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. Caution: Invisible laser radiation when open and interlocks defeate

14、d avoid expo- sure to beam. Advarsel:Usynling laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ATTENTION Luti

15、lisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL! Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product

16、. The CLASS 1 LASER PRODUCT label is located on the rear exterior. This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMI

17、SSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT Precaution to replace Optical block (KSM-880CAB) 1) After the connection, remove so

18、lder shown in the right figure. Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. solder PICK-UP Assy P.C.B RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage

19、 (V)Discharging Rated power (W)Parts number (C101, 102)resistor ( ) 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schema

20、tic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of t

21、he MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMP

22、UTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 1Turn on the AC main power. 2Confirm that the m

23、ain power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power s

24、upply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur.

25、 In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 1Remove the AC power cord. 2Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 3Contact

26、 the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 4Contact the same end of the discharging resistor as step 3 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 5Check that voltage across C101 and C102 has decreased to 1 V or

27、less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table. MAIN C.B D101 C101C102 34 22 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the mac

28、hine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective an

29、d to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord. 2Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3Connect t

30、he AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schemat

31、ic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor so

32、ldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 18 15 C113 18 15 Short with tweezers. 6 REF. NOPART NO.KANRIDESCRIPTION NO. REF. NOPART NO.KANRIDESCRIPTION NO. ELECTRICAL MAIN PARTS LIST IC 87-020-454-010 IC,DN6851 87-A21-417-010 IC,STK490

33、-310 8A-NF8-625-030 C-IC,LC866548V-* 8A-NF8-611-010 C-IC,LC866560W-5P19 8A-NF8-612-010 C-IC,LC866548V-5P03 87-A21-396-010 IC,STK490-040 87-A21-629-010 IC,SPS-442-1-N 87-A21-482-010 IC,RPM6938-H4 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-577-040 C-IC,M61506FP 87-A21-023-040 C-IC,BA3835F 87-A21-401-04

34、0 C-IC,M61503FP 87-070-289-040 C-IC,BU2092F 87-A21-415-010 IC,LA1843 87-A20-440-040 C-IC,BU1920FS 87-070-127-110 IC,LC72131D TRANSISTOR 87-026-451-080 TR,2SA933S 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370E 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA123

35、5F 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-087-080 C-FET,2SK2158 87-A30-074-080 C-TR,RT1P 141C 87-A30-318-080 TR,CSA952K 87-A30-495-080 TR,2SA1981Y 87-A30-091-080 FET,2SJ460 87-A30-329-080 TR,CD1585BC 87-A30-090-080 FET,

36、2SK2541 87-A30-104-080 C-TR,RT1N 441C 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-073-080 C-TR,RT1N 141C 89-333-317-880 TR,2SC3331(T/U) 87-A30-269-040 C-FET,2SJ461-T1 89-327-143-080 C-TR,2SC2714O 87-A30-489-080 C-TR,KRA107S 87-A30-086-070 C-TR,CSD1306E 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC41

37、15BC DIODE 87-A40-393-090 DIODE,1N5402GW(F20) 87-A40-736-080 DIODE,1N4148M(SEM) 87-A40-547-090 DIODE,D5SBA20 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-776-080 ZENER,UZ27BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-270-080 C-DIODE,MC2838 87-A40-313-080 C-DIODE,MC2840 87-A40-269-

38、080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-020-465-080 DIODE,1SS133 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-802-080 ZENER,UZ5.1BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L MAIN C.B C0003 87-012-368-080 C-CAP,S 0.1-50 Z F C0004 87-012-368-080 C-CAP,S 0.1-50 Z F C0005 87-012-368

39、-080 C-CAP,S 0.1-50 Z F C0006 87-012-368-080 C-CAP,S 0.1-50 Z F C0009 87-012-368-080 C-CAP,S 0.1-50 Z F C0010 87-012-368-080 C-CAP,S 0.1-50 Z F C0011 87-012-368-080 C-CAP,S 0.1-50 Z F C0012 87-012-368-080 C-CAP,S 0.1-50 Z F C0015 87-012-368-080 C-CAP,S 0.1-50 Z F C0016 87-012-368-080 C-CAP,S 0.1-50

40、Z F C0017 87-012-368-080 C-CAP,S 0.1-50 Z F C0018 87-012-368-080 C-CAP,S 0.1-50 Z F C0019 87-016-520-000 CAP,E 3300-65 M SMG C0020 87-016-520-000 CAP,E 3300-65 M SMG C0021 87-016-051-000 CAP,E 2200-35 M SMG C0022 87-016-051-000 CAP,E 2200-35 M SMG C0023 87-016-658-000 CAP,E 4700-35 M SMG C0024 87-01

41、6-658-000 CAP,E 4700-35 M SMG C0025 87-010-408-080 CAP,E 47-50 M 11L SME C0026 87-010-247-080 CAP,E 100-50 M SME C0030 87-010-430-080 CAP,E 100-63 C0031 87-010-263-080 CAP,E 100-10 M 11L SME C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0034 87-010-260-080 CAP,E 47-25 M 11L SME C0035 87-010-380-08

42、0 CAP,E 47-16 M 11L SME C0036 87-010-381-080 CAP,E 330-16 M SME C0038 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME C0061 87-010-260-080 CAP,E 47-25 M 11L SME C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0103 87-0

43、10-545-080 CAP,E 0.22-50 M 11L SME C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME C0107 87-010-405-080 CAP,E 10-50 M 11L SME C0108 87-010-405-080 CAP,E 10-50 M 11L SME C0111 87-010-405-080 CAP,E 10-50 M 11L SME C0112 87-010-405-080 CAP,E 10-50 M 11L SME C0113 87-010-866-080 CAP,E 10-63 M VX C0114 87-0

44、10-866-080 CAP,E 10-63 M VX C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0123 87-010-176-080 C-CAP,S 680P-50 J C0124 87-010-176-080 C-CAP,S 680P-50 J C0125 87-012-368-080 C-CAP,S 0.1-50 Z F C0126 87-012-368-080 C-CAP,S 0.1-50 Z F C0127 87-012-368-080

45、 C-CAP,S 0.1-50 Z F C0128 87-012-368-080 C-CAP,S 0.1-50 Z F C0129 87-010-191-080 C-CAP,S 0.015-50 C0130 87-010-191-080 C-CAP,S 0.015-50 C0131 87-010-197-080 C-CAP,S 0.01-25 K C0132 87-010-197-080 C-CAP,S 0.01-25 K C0133 87-010-186-080 C-CAP,S 4700P-50 K B C2012 C0140 87-010-182-080 C-CAP,S 2200P-50

46、K B C2012 C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0203 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0204 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0205 87-012-140-080 C-CAP,S 470P-50 J CH C0206 87-012-140-080 C-CAP,S 470P-50 J CH C0209 87-010-402-080 CAP,E 2.2-50 M 11L SME C0210 87-010-402-080

47、 CAP,E 2.2-50 M 11L SME C0211 87-010-184-080 C-CAP,S 3300P-50 K B C2012 C0212 87-010-184-080 C-CAP,S 3300P-50 K B C2012 C0213 87-010-402-080 CAP,E 2.2-50 M 11L SME C0214 87-010-402-080 CAP,E 2.2-50 M 11L SME C0217 87-010-405-080 CAP,E 10-50 M 11L SME C0218 87-010-405-080 CAP,E 10-50 M 11L SME C0220

48、87-010-405-080 CAP,E 10-50 M 11L SME C0223 87-010-190-080 C-CAP,S 0.01-50 Z F C2012 C0224 87-010-190-080 C-CAP,S 0.01-50 Z F C2012 C0228 87-010-405-080 CAP,E 10-50 M 11L SME 7 REF. NOPART NO.KANRIDESCRIPTION NO. REF. NOPART NO.KANRIDESCRIPTION NO. C0229 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0230 87-010-196-080 C-CAP,S 0