Aiwa-NSXSZ42-cs-sm 电路图 维修手册.pdf

《Aiwa-NSXSZ42-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXSZ42-cs-sm 电路图 维修手册.pdf（27页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL DATA NSXSZ40 RCZAS01 SYSTEM CD CASSEIVER REMOTE CONTROLLER CXNSZ40 COMPACT DISC STEREO SYSTEM BASIC TAPE MECHANISM : 6ZM-3 PR2NM BASIC CD MECHANISM : AZG-1 ZA3RDM NSX-SZ40EZ S/M Code No. 09-004-424-6N6 If requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M

2、Code No. 09-001-335-3NC). SPEAKER SXNSZ51 NSX-SZ42EZ NSXSZ42CXNSZ42SXNSZ53 RadioFans.CN 收音机爱 好者资料库 2 Main unit CX-NSZ40, CX-NSZ42 FM tuner section Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)16.8 dBf Antenna terminal75 ohms (unbalanced) AM (MW) tuner section Tuning range531 kHz to 1602 k

3、Hz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) Usable sensitivity350 V/m AntennaLoop antenna LW tuner section Tuning range144 kHz to 290 kHz Usable sensitivity1400 V/m AntennaLoop antenna Amplifier section Power outputRated: 80 W + 80 W (6 ohms, T.H.D. 1 %, 1 kHz/DIN 45500) Reference: 100 W +100

4、W (6 ohms, T.H.D. 10 %, 1 kHz/DIN 45324) DIN MUSIC POWER: 200 W + 200 W Total harmonic distortion0.1 % (45 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV OutputsSPEAKERS: accept speakers of 6 ohms or more SURROUND SPEAKERS: accept speakers of 8 ohms to 16 ohms PHONES (stereo jack): accepts hea

5、dphones of 32 ohms or more SPECIFICATIONS Cassette deck section Track format4 tracks, 2 channels stereo Frequency response50 Hz 15000 Hz Recording systemAC bias HeadsDeck 1: Playback head x 1 Deck 2: Recording/playback head x 1, erase head x 1 Compact disc player section LaserSemiconductor laser ( =

6、 780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Wow and flutterUnmeasurable General Power requirements230 V AC, 50 Hz Power consumption150 W Power consumption in standby mode If the power-economizing mode is ECO OFF: 20 W If the power

7、-economizing mode is ECO ON or ECO AUTO: 0.9 W Dimensions of main unit260 x 326 x 345 mm (W x H x D) Weight of main unit8.3 kg Speaker system SX-NSZ51, SX-NSZ53 Speaker system3 way, Bass reflex (magnetic shielded type) Speaker unitsWoofer: 140 mm cone type Tweeter: 60 mm cone type Super tweeter: 20

8、mm ceramic type Impedance6 ohms Sensitvity87 dB/W/m Dimensions (W x H x D)240 x 324 x 270 mm Weight4.0 kg Design and specifications are subject to change without notice. The word “BBE” and the “BBE symbol” are trademarks of BBE Sound, Inc. Under license from BBE Sound, Inc. REF. NOPART NO.KANRIDESCR

9、IPTION NO. ACCESSORIES LIST 1 8A-NF8-927-010 IB,EZ(9L)M 42(RDS) 1 8A-NF8-928-010 IB,EZ(9L)M 40 2 8Z-NF8-702-010 RC UNIT,RC-ZAS01 3 87-006-225-010 ANT,LOOP ANT NC2 4 87-A90-118-010 ANT,WIRE FM(Z) RadioFans.CN 收音机爱 好者资料库 3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING VAROITUS! Laiteen K ytt min

10、en muulla kuin t ss k ytt ohjeessa mainit- ulla tavalla saattaa altistaa k yt-t j n turvallisuusluokan 1 ylit- t v lle n kym tt m lle lasers teilylle. VARNING! Om apparaten anv nds p annat s tt n vad som specificeras i denna bruksanvising, kan anv ndaren uts ttas f r osynling laserstr lning, som ver

11、skrider gr nsen f r laserklass 1. Caution: Invisible laser radiation when open and interlocks defeated avoid expo- sure to beam. Advarsel:Usynling laserst ling ved bning, n r sikkerhedsafbrydere er ude af funktion. Undg uds ttelse for str ling. CAUTION Use of controls or adjustments or performance o

12、f procedures other than those specified herein may result in hazardous radiation exposure. ATTENTION Lutilisation de commandes, r glages ou proc dures autres que ceux sp cifi s peut entra ner une dangereuse exposition aux radiations. ADVARSEL! Usynlig laserst ling ved bning, n r sikkerhedsafbryderee

13、r ude af funktion. Undg uds ttelse for str ling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SER

14、VICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER PRODUCT LASER PRO

15、DUKT LASER LAITE LASER APPARAT Precaution to replace Optical block 1) After the connection, remove solder shown in the figure below. Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode

16、. Solder ZA8/ZD8 MODEL ZA3/ZA4 (KSS-213F) MODEL RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic ca

17、pacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Excha

18、nge the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot

19、 be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets

20、the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 1Turn on the AC main power. 2Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to b

21、e working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors

22、 (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 1Remove the AC power cord. 2Connect a discharging resist

23、or at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 3Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 4Contact the same end of the discharging resistor as step 3 to the negative (-)

24、 side (-VH) of C102 in the same way. (For two seconds) 5Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table. MAIN C.B D101 C101C102 34 22 5 In such a case, check also if the POWER A

25、MPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is perfo

26、rmed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord. 2Sh

27、ort both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110)

28、 and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above descr

29、ibed procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 18 15 C113 18 15 Short with tweezers. 6 REF. NOPART NO.KANRIDESCRIPTION

30、 NO. REF. NOPART NO.KANRIDESCRIPTION NO. ELECTRICAL MAIN PARTS LIST IC 87-020-454-010 IC,DN6851 87-A21-355-010 IC,STK490-140 8A-NF8-620-010 C-IC,LC866548V-5R49 8A-NF8-621-010 C-IC,LC866560W-5R50 87-A21-629-010 IC,SPS-442-1-N 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-577-040 C-IC,M61506FP 87-070-289-

31、040 C-IC,BU2092F 87-A21-401-040 C-IC,M61503FP 87-A21-560-010 IC,LA1844L-A 87-A20-440-040 C-IC,BU1920FS 87-070-127-110 IC,LC72131D TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370E 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-026-245-080 TR,

32、DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-087-080 C-FET,2SK2158 87-A30-074-080 C-TR,RT1P 141C 87-A30-318-080 TR,CSA952K 87-A30-091-080 FET,2SJ460 87-A30-329-080 TR,CD1585BC 87-A30-090-080 FET,2SK2541 87-A30-104-080 C-TR,RT1N 441C 87-A30-468

33、-080 C-TR,KRC102S-RTK 87-A30-484-080 C-TR,KRA102S 89-333-317-880 TR,2SC3331(T/U) 89-327-143-080 C-TR,2SC2714O 87-A30-489-080 C-TR,KRA107S 87-A30-086-070 C-TR,CSD1306E 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC4115BC DIODE 87-A40-393-090 DIODE,1N5402GW(F20) 87-020-465-080 DIODE,1SS133 87-A40-

34、547-090 DIODE,D5SBA20 87-A40-553-080 DIODE,1N4003 LES 87-A40-776-080 ZENER,UZ27BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-270-080 C-DIODE,MC2838 87-A40-313-080 C-DIODE,MC2840 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-802-080 ZENER,UZ5.1BSC 87-A40-73

35、9-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L MAIN C.B C0003 87-012-368-080 C-CAP,S 0.1-50 Z F C0004 87-012-368-080 C-CAP,S 0.1-50 Z F C0005 87-012-368-080 C-CAP,S 0.1-50 Z F C0006 87-012-368-080 C-CAP,S 0.1-50 Z F C0015 87-012-368-080 C-CAP,S 0.1-50 Z F C0016 87-012-368-080 C-CAP,S 0.1-50 Z F C

36、0017 87-012-368-080 C-CAP,S 0.1-50 Z F C0018 87-012-368-080 C-CAP,S 0.1-50 Z F C0019 87-016-520-000 CAP,E 3300-65 M SMG C0020 87-016-520-000 CAP,E 3300-65 M SMG C0023 87-016-658-000 CAP,E 4700-35 M SMG C0024 87-016-658-000 CAP,E 4700-35 M SMG C0025 87-010-408-080 CAP,E 47-50 M 11L SME C0026 87-010-2

37、47-080 CAP,E 100-50 M SME C0030 87-010-430-080 CAP,E 100-63 C0031 87-010-263-080 CAP,E 100-10 M 11L SME C0032 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0034 87-010-260-080 CAP,E 47-25 M 11L SME C0035 87-010-380-080 CAP,E 47-16 M 11L SME C0036 87-010-381-080 CAP,E 330-16 M SME C0038 87-010-197-080 C-

38、CAP,S 0.01-25 K B C2012 C0060 87-010-403-080 CAP,E 3.3-50 M 11L SME C0061 87-010-260-080 CAP,E 47-25 M 11L SME C0101 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0102 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0103 87-010-545-080 CAP,E 0.22-50 M 11L SME C0104 87-010-545-080 CAP,E 0.22-50 M 11L SME C0107 8

39、7-010-405-080 CAP,E 10-50 M 11L SME C0108 87-010-405-080 CAP,E 10-50 M 11L SME C0109 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0110 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0111 87-010-405-080 CAP,E 10-50 M 11L SME C0112 87-010-405-080 CAP,E 10-50 M 11L SME C0113 87-A12-180-080 CAP,E 10-63 M 105 KME

40、C0114 87-A12-180-080 CAP,E 10-63 M 105 KME C0119 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0120 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0123 87-010-176-080 C-CAP,S 680P-50 J SL C0124 87-010-176-080 C-CAP,S 680P-50 J SL C0125 87-012-368-080 C-CAP,S 0.1-50 Z F C0126 87-012-368-080 C-CAP,S 0.1-50 Z F

41、 C0127 87-012-368-080 C-CAP,S 0.1-50 Z F C0128 87-012-368-080 C-CAP,S 0.1-50 Z F C0129 87-010-191-080 C-CAP,S 0.015-50 Z F GRM C0130 87-010-191-080 C-CAP,S 0.015-50 Z F GRM C0131 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0132 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0133 87-010-186-080 C-CAP,S 4700

42、P-50 K B C2012 C0134 87-010-379-080 CAP,E 22-16 M 11L SME C0140 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0141 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0237 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0238 87-010-322-080 C-CAP,S 100P-50 J CH GRM C0301 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0302 87

43、-010-178-080 C-CAP,S 1000P-50 K B C2012 C0303 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0304 87-010-179-080 C-CAP,S 1200P-50 K B GRM C0307 87-010-263-080 CAP,E 100-10 M 11L SME C0308 87-010-263-080 CAP,E 100-10 M 11L SME C0309 87-010-318-080 C-CAP,S 47P-50 J CH GRM C0310 87-010-318-080 C-CAP,S 47P-50

44、 J CH GRM C0313 87-010-188-080 C-CAP,S 6800P-50 K B C2012 C0314 87-010-188-080 C-CAP,S 6800P-50 K B C2012 C0315 87-010-263-080 CAP,E 100-10 M 11L SME C0317 87-010-546-080 CAP,E 0.33-50 M 11L SME C0318 87-010-546-080 CAP,E 0.33-50 M 11L SME C0326 87-010-198-080 C-CAP,S 0.022-25 K B C2012 C0327 87-012

45、-368-080 C-CAP,S 0.1-50 Z F C0360 87-010-401-080 CAP,E 1-50 M 11L SME C0365 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0399 87-012-140-080 C-CAP,S 470P-50 J CH C0401 87-010-544-080 CAP,E 0.1-50 M 11L SME C0402 87-010-544-080 CAP,E 0.1-50 M 11L SME C0403 87-010-321-080 C-CAP,S 82P-50 J CH C0404 87-010

46、-321-080 C-CAP,S 82P-50 J CH C0405 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0406 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0407 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0408 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0409 87-010-182-080 C-CAP,S 2200P-50 K B C2012 7 REF. NOPART NO.KANRIDESCRIPTION N

47、O. REF. NOPART NO.KANRIDESCRIPTION NO. C0410 87-010-182-080 C-CAP,S 2200P-50 K B C2012 C0411 87-010-405-080 CAP,E 10-50 M 11L SME C0412 87-010-405-080 CAP,E 10-50 M 11L SME C0452 87-010-382-080 CAP,E 22-25 M 11L SME C0453 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0454 87-010-183-080 C-CAP,S 2700P-50

48、K B GRM C0455 87-010-183-080 C-CAP,S 2700P-50 K B GRM C0456 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C0458 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C0459 87-010-175-080 C-CAP,S 560P-50 J SL C0460 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C0461 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0462 87-012-158-080 C-CAP,S 390P-50 J CH GRM C0521 87-010-546-080 CAP,