Aiwa-NS-ZSZ10E-Service-Manual(1) 电路图 维修手册.pdf

《Aiwa-NS-ZSZ10E-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NS-ZSZ10E-Service-Manual(1) 电路图 维修手册.pdf（12页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL NSX-AJ10 SPEAKER SYSTEM CD CASSEIVER REMOTE CONTROLLER NSX-SZ10 CX-NAJ10SX-NAJ12 CX-NSZ10SX-NSZ15RC-ZAS02 COMPACT DISC STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : ZZM-2 PR1NM / PR1NC BASIC CD MECHANISM : AZG-1 NSX-AJ10 NSX-SZ10 NSZ-SZ10E U LH HA S/M Code No. 09-003-424-8R1 REVISIO

2、N If requiring information about the CD mechanism, see Service Manual of AZG-1 ZD8RNDM, (S/M Code No. 09-001-335-3N6) and AZG-1 ZD8RNDC, (S/M Code No. 09-001-335-3NA). This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-AJ10(U)/NSX-SZ10(LH), (S/M Code No. 09-99C-424-8T1

3、). NSX-SZ10ECX-NSZ10ESX-NSZ15 CD MECHANISM ZD8RNDC ZD8RNDC ZD8RNDM DATA RadioFans.CN 收音机爱 好者资料库 Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350

4、V/m AntennaLoop antenna Power outputRated 28 W + 28 W (1 kHz, T.H.D. 1 %, 6 ohms) Reference 35 W + 35 W (1 kHz, T.H.D. 10 %, 6 ohms) Total harmonic distortion 0.1 % (14 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV OutputsSPEAKERS: accept speakers of 6 ohms or more PHONES (stereo jack): accep

5、ts headphones of 32 ohms or more Track format4 tracks, 2 channels stereo Frequency response50 Hz 8000 Hz Recording systemAC bias HeadsDeck 1 : Recording/playback head x 1, erase head x 1 Deck 2 : Playback head x 1 SPECIFICATIONS LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-n

6、oise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm cone type Tweeter: 20mm ceramic type Impedance6 ohms Sensitivity86 dB/W/m Dimensions (W x H x D)220 x 324 x 204 mm Weight2.0 kg Power requiremen

7、ts120 V/220-230 V/240 V AC (switchable), 50/60 Hz Power consumption55 W Power consumptionWith power-economizing in standby modemode off : 12 W With power-economizing mode on : 0.9 W Dimensions of main unit260 x 324 x 346 mm (W x H x D) Weight of main unit5.7 kg Design and specifications are subject

8、to change without notice. Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)13.2 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350 V/m AntennaLoop antenna Power outputRated 10 W + 10 W (50 Hz to 20 kHz

9、, T.H.D. 1 %, 6 ohms) Reference 15 W + 15 W (1 kHz, T.H.D. 10 %, 6 ohms) Total harmonic distortion 0.1 % (6 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV OutputsSPEAKERS: accept speakers of 6 ohms or more PHONES (stereo jack): accepts headphones of 32 ohms or more Track format4 tracks, 2 chan

10、nels stereo Frequency response50 Hz 8000 Hz Recording systemAC bias HeadsDeck 1 : Recording/playback head x 1, erase head x 1 Deck 2 : Playback head x 1 SPECIFICATIONS LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kH

11、z, 0 dB) Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm cone type Tweeter: 20mm ceramic type Impedance6 ohms Sensitivity86 dB/W/m Dimensions (W x H x D)220 x 324 x 235 mm Weight2.0 kg Power requirements120 V AC, 60 Hz Power consumption38 W Power consumptionWith

12、 power-economizing in standby modemode off : 8.0 W With power-economizing mode on : 0.9 W Dimensions of main unit260 x 324 x 346 mm (W x H x D) Weight of main unit5.7 kg Design and specifications are subject to change without notice. 2 RadioFans.CN 收音机爱 好者资料库 PICK-UP Assy P.C.B PROTECTION OF EYES FR

13、OM LASER BEAM DURING SERVICING VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainit- ulla tavalla saattaa altistaa kyt-tjn turvallisuusluokan 1 ylit- tvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksanvising, kan anvndaren utstt

14、as fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. Caution: Invisible laser radiation when open and interlocks defeated avoid expo- sure to beam. Advarsel:Usynling laserstling ved bning, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. CAUTION Use of controls

15、or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ATTENTION Lutilisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL! Usynlig laserstling ved bning,

16、 nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. This set employs laser. Therefore, be sure to follow carefully the instructions below when servic

17、ing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 L

18、ASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT Precaution to replace Optical block (KSM-880CAB) 1) After the connection, remove solder shown in the right figure. Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care

19、 the clothes do not touch the diode. solder 3 RadioFans.CN 收音机爱 好者资料库 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C101, C102) of the electrolytic capaci

20、tors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange

21、the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be

22、turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the

23、HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 1Turn on the AC main power. 22Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 3When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be w

24、orking correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C

25、101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11Remove the AC power cord. 22Connect a discharging resisto

26、r at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44Contact the same end of the discharging resistor as step 3 to the negative (-

27、) side (-VH) of C102 in the same way. (For two seconds) 55Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-1 MAIN C.B D101 C101C102 22 34 4 In such a case, check also if the

28、POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) i

29、s performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1Remove the AC power cor

30、d. 2Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor

31、(Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above

32、 described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B VSS VDD C113 * % C113 18 15 Short with tweezers. 5 ELECTRICAL MAIN PARTS LIST

33、DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8A-MA6-651-010 C-IC,M38B59MFH-E250FP 8A-NFA-615-010 C-IC,M38B57MCH-E236FP 87-A21-397-010 IC,STK490-070 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-443-040 C-IC,M62495AFP 87-A21-415-010 IC,LA1843 87-070-127-110 IC,LC72131 D 8

34、7-A21-482-010 IC,RPM6938-H4 TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-255-010 C-TR,2SB1342 87-A30-256-010 TR,2SD1933 87-A30-190-080 TR,CC5551 87-026-245-080 TR,DTC114ES 87-A30-1

35、98-080 TR,KTC3199GR 87-A30-090-080 FET,2SK2541 87-A30-484-080 C-TR,KRA102S 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-107-070 C-TR,CMBT5401 87-A30-106-040 C-TR,CMBT5551 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-318-080 TR,CSA952K 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-234-080 TR,CSC4

36、115BC 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-TR,KRA107S DIODE 87-A40-736-080 DIODE,1N4148M (SEM) 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-774-080 ZENER,UZ24BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A4

37、0-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-A40-535-080 DIODE,1N5393-GOODARK MAIN C.B C3 87-010-196-080 CHIP CAPACITOR,0.1-25 C4 87-010-196-080 CHIP CAPACITOR,0.1-25 C5

38、 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-196-080 CHIP CAPACITOR,0.1-25 C9 87-010-196-080 CHIP CAPACITOR,0.1-25 C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A10-627-000 CAP,E 2200-50 M SMG C20 87-A10-627-000 C

39、AP,E 2200-50 M SMG C21 87-016-495-000 CAP,E 3300-25 M SMG C22 87-016-495-000 CAP,E 3300-25 M SMG C22 87-A10-011-090 CAP,E 2200-25 SMG C25 87-010-385-080 CAP, ELECT 220-25V C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME C26 87-010-247-080 CAP, ELECT 100-50V C26 87-010-406-080 CAP, ELECT 22-50 C30 87-0

40、10-247-080 CAP, ELECT 100-50V C30 87-010-384-080 CAP, ELECT 100-25 M 11L SME C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-263-080 CAP, ELECT 100-10V C34 87-010-247-080 CAP, ELECT 100-50V C35 87-010-406-080 CAP, ELECT 22-50 C36 87-010-381-080 CAP, ELECT 330-16

41、V C38 87-A11-567-080 C-CAP,S 0.01-50 K B C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME C60 87-010-403-080 CAP, ELECT 3.3-50V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C100 87-018-127-080 CAP TC-U 470P C101 87-010-183-080 C-CAP,S 2700P-50 B C101 87-010-185-080 C-CAP,S 3900P-50 KB C102 87-010-183-080

42、C-CAP,S 2700P-50 B C102 87-010-185-080 C-CAP,S 3900P-50 KB C103 87-010-545-080 CAP, ELECT 0.22-50V C104 87-010-545-080 CAP, ELECT 0.22-50V C105 87-010-178-080 CHIP CAP 1000P C105 87-010-186-080 CAP,CHIP 4700P C106 87-010-178-080 CHIP CAP 1000P C106 87-010-186-080 CAP,CHIP 4700P C107 87-010-404-080 C

43、AP, ELECT 4.7-50V C107 87-010-403-080 CAP, ELECT 3.3-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-403-080 CAP, ELECT 3.3-50V C111 87-010-391-080 CAP,E 10-35 SME C111 87-010-406-080 CAP, ELECT 22-50 C112 87-010-391-080 CAP,E 10-35 SME C112 87-010-406-080 CAP, ELECT 22-50 C113 87-010-405-080

44、 CAP, ELECT 10-50V C113 87-012-156-080 C-CAP, S 220P-50 J CH C114 87-010-405-080 CAP, ELECT 10-50V C114 87-012-156-080 C-CAP, S 220P-50 J CH C119 87-010-197-080 CAP, CHIP 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C125 87-012-368-080 C-CAP,S 0.1-50 F C125 87-010-196-080 CHIP CAPACITOR,0.1-25 C126

45、 87-012-368-080 C-CAP,S 0.1-50 F C126 87-010-196-080 CHIP CAPACITOR,0.1-25 C127 87-012-368-080 C-CAP,S 0.1-50 F C127 87-010-196-080 CHIP CAPACITOR,0.1-25 C128 87-012-368-080 C-CAP,S 0.1-50 F C128 87-010-196-080 CHIP CAPACITOR,0.1-25 C129 87-A10-592-080 C-CAP,S 0.015-50 K B C130 87-A10-592-080 C-CAP,

46、S 0.015-50 K B C131 87-010-197-080 CAP, CHIP 0.01 DM C132 87-010-197-080 CAP, CHIP 0.01 DM C133 87-010-186-080 CAP,CHIP 4700P C140 87-010-182-080 C-CAP,S 2200P-50 B C183 87-010-387-080 CAP,E 470-25 SME C184 87-010-403-080 CAP, ELECT 3.3-50V C200 87-018-195-080 CAP TC-U 1200P C300 87-018-195-080 CAP

47、TC-U 1200P C301 87-010-179-080 CAP,CHIP S B1200P C302 87-010-179-080 CAP,CHIP S B1200P C303 87-010-178-080 CHIP CAP 1000P C304 87-010-178-080 CHIP CAP 1000P C305 87-010-198-080 CAP, CHIP 0.022 C307 87-010-263-080 CAP, ELECT 100-10V C308 87-010-263-080 CAP, ELECT 100-10V C311 87-010-598-080 C-CAP,S 0

48、.068-16VRK C312 87-010-598-080 C-CAP,S 0.068-16VRK C313 87-010-188-080 CAP,CHIP 6800P C314 87-010-188-080 CAP,CHIP 6800P C315 87-010-263-080 CAP, ELECT 100-10V C317 87-010-546-080 CAP, ELECT 0.33-50V C318 87-010-546-080 CAP, ELECT 0.33-50V 6 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO.