Hitachi-AXF300-mc-sm 电路图 维修手册.pdf

《Hitachi-AXF300-mc-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Hitachi-AXF300-mc-sm 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、 SM0101 AX-F300/HMD-R50AX-F300/HMD-R50AX-F300/HMD-R50AX-F300/HMD-R50AX-F300/HMD-R50 UC, E, E(BS), W, W(UN) CD MECHANISM CDV300DW MD MECHANISM MDM-99X SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT September 2000September 2000September 2000September 2000September 2000 MINI COMPONENT H

2、I-FI SYSTEMMINI COMPONENT HI-FI SYSTEMMINI COMPONENT HI-FI SYSTEMMINI COMPONENT HI-FI SYSTEMMINI COMPONENT HI-FI SYSTEM HITHITHITHITHITA A A A ACHI CONSUMER PRCHI CONSUMER PRCHI CONSUMER PRCHI CONSUMER PRCHI CONSUMER PRODUCTS (S)ODUCTS (S)ODUCTS (S)ODUCTS (S)ODUCTS (S) CONTENTSCONTENTSCONTENTSCONTEN

3、TSCONTENTS SPECIFICATIONS .3 SERVICE POINTS .4 ADJUSTMENTS .10 WIRING DIAGRAMS.11 PRINTED WIRING BOARDS .14 BLOCK DIAGRAM .25 CIRCUIT DIAGRAM .29 EXPLODED VIEW.53 REPLACEMENT PARTS LIST .56 CAUTIONCAUTIONCAUTIONCAUTIONCAUTION DANGERDANGERDANGERDANGERDANGER Invisible laser radiation when open and int

4、erlocks failed or defeated. AVOID DIRECT EXPOSURE TO BEAM.Invisible laser radiation when open and interlocks failed or defeated. AVOID DIRECT EXPOSURE TO BEAM.Invisible laser radiation when open and interlocks failed or defeated. AVOID DIRECT EXPOSURE TO BEAM.Invisible laser radiation when open and

5、interlocks failed or defeated. AVOID DIRECT EXPOSURE TO BEAM.Invisible laser radiation when open and interlocks failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. GEFAHRGEFAHRGEFAHRGEFAHRGEFAHR Unsichtbare Laser-Strahlung wenn Interlock (Blockierung) funktionsuntchtig oder abgeschaltet.Unsichtbare L

6、aser-Strahlung wenn Interlock (Blockierung) funktionsuntchtig oder abgeschaltet.Unsichtbare Laser-Strahlung wenn Interlock (Blockierung) funktionsuntchtig oder abgeschaltet.Unsichtbare Laser-Strahlung wenn Interlock (Blockierung) funktionsuntchtig oder abgeschaltet.Unsichtbare Laser-Strahlung wenn I

7、nterlock (Blockierung) funktionsuntchtig oder abgeschaltet. UNMITTELBAREN KONTAKT MIT DEM STRAHL UNBEDIGT VERMEIDEN.UNMITTELBAREN KONTAKT MIT DEM STRAHL UNBEDIGT VERMEIDEN.UNMITTELBAREN KONTAKT MIT DEM STRAHL UNBEDIGT VERMEIDEN.UNMITTELBAREN KONTAKT MIT DEM STRAHL UNBEDIGT VERMEIDEN.UNMITTELBAREN KO

8、NTAKT MIT DEM STRAHL UNBEDIGT VERMEIDEN. DANGERDANGERDANGERDANGERDANGER Faire trs attention aux radiations mises par le faisceau laser invisible au dfaillance du verrouillage.Faire trs attention aux radiations mises par le faisceau laser invisible au dfaillance du verrouillage.Faire trs attention au

9、x radiations mises par le faisceau laser invisible au dfaillance du verrouillage.Faire trs attention aux radiations mises par le faisceau laser invisible au dfaillance du verrouillage.Faire trs attention aux radiations mises par le faisceau laser invisible au dfaillance du verrouillage. NE JAMAIS SE

10、XPOSER DIRECTEMENT AU FAISCEAU.NE JAMAIS SEXPOSER DIRECTEMENT AU FAISCEAU.NE JAMAIS SEXPOSER DIRECTEMENT AU FAISCEAU.NE JAMAIS SEXPOSER DIRECTEMENT AU FAISCEAU.NE JAMAIS SEXPOSER DIRECTEMENT AU FAISCEAU. VARNINGVARNINGVARNINGVARNINGVARNING Nr apparaten ppnats och skyddsanordningen felar eller satts

11、ur funktion frekommer osynlig laserstrlning.Nr apparaten ppnats och skyddsanordningen felar eller satts ur funktion frekommer osynlig laserstrlning.Nr apparaten ppnats och skyddsanordningen felar eller satts ur funktion frekommer osynlig laserstrlning.Nr apparaten ppnats och skyddsanordningen felar

12、eller satts ur funktion frekommer osynlig laserstrlning.Nr apparaten ppnats och skyddsanordningen felar eller satts ur funktion frekommer osynlig laserstrlning. UNDVIK DIREKT BESTRLNING.UNDVIK DIREKT BESTRLNING.UNDVIK DIREKT BESTRLNING.UNDVIK DIREKT BESTRLNING.UNDVIK DIREKT BESTRLNING. ADVARSELADVAR

13、SELADVARSELADVARSELADVARSEL r apparatet bnes og beskyttelsesanordningen ikke virker eller sttes un af funktion, forekommer der usynlig laserstrling.r apparatet bnes og beskyttelsesanordningen ikke virker eller sttes un af funktion, forekommer der usynlig laserstrling.r apparatet bnes og beskyttelses

14、anordningen ikke virker eller sttes un af funktion, forekommer der usynlig laserstrling.r apparatet bnes og beskyttelsesanordningen ikke virker eller sttes un af funktion, forekommer der usynlig laserstrling.r apparatet bnes og beskyttelsesanordningen ikke virker eller sttes un af funktion, forekomm

15、er der usynlig laserstrling. UNDG DIREKTE BESTRLING.UNDG DIREKTE BESTRLING.UNDG DIREKTE BESTRLING.UNDG DIREKTE BESTRLING.UNDG DIREKTE BESTRLING. ADVARSELADVARSELADVARSELADVARSELADVARSEL Nr denne delen er apen som flge av at lsen er utkoplet eller ikke fungerer, eksisterer det usynlig laserstrling.Nr

16、 denne delen er apen som flge av at lsen er utkoplet eller ikke fungerer, eksisterer det usynlig laserstrling.Nr denne delen er apen som flge av at lsen er utkoplet eller ikke fungerer, eksisterer det usynlig laserstrling.Nr denne delen er apen som flge av at lsen er utkoplet eller ikke fungerer, ek

17、sisterer det usynlig laserstrling.Nr denne delen er apen som flge av at lsen er utkoplet eller ikke fungerer, eksisterer det usynlig laserstrling. UNNG BLI UTSATT FOR DIREKTE BESTRLING!UNNG BLI UTSATT FOR DIREKTE BESTRLING!UNNG BLI UTSATT FOR DIREKTE BESTRLING!UNNG BLI UTSATT FOR DIREKTE BESTRLING!U

18、NNG BLI UTSATT FOR DIREKTE BESTRLING! VARIOITSVARIOITSVARIOITSVARIOITSVARIOITS Laite lhett nkymtnt lasersteily, kun se avataan ja kun sisiset turvalukot eivt toimi.Laite lhett nkymtnt lasersteily, kun se avataan ja kun sisiset turvalukot eivt toimi.Laite lhett nkymtnt lasersteily, kun se avataan ja

19、kun sisiset turvalukot eivt toimi.Laite lhett nkymtnt lasersteily, kun se avataan ja kun sisiset turvalukot eivt toimi.Laite lhett nkymtnt lasersteily, kun se avataan ja kun sisiset turvalukot eivt toimi. VARO JOUTUMASTA ALTTIIKSI STEILYLLE.VARO JOUTUMASTA ALTTIIKSI STEILYLLE.VARO JOUTUMASTA ALTTIIK

20、SI STEILYLLE.VARO JOUTUMASTA ALTTIIKSI STEILYLLE.VARO JOUTUMASTA ALTTIIKSI STEILYLLE. RadioFans.CN 收音机爱 好者资料库 2 AX-F300 Check that exposed parts are acceptably insulated from the supply circuit before returning the repaired instrument to the customer. Checking methodChecking methodChecking methodChe

21、cking methodChecking method Measure the resistance value between the both poles of attachment cup (Power supply plug) and the exposed parts (Parts such as Knob, Cover, etc. where the cus- tomer is easy to touch.) and check that the resistance value is 500 kohms or more. INSTRUMENT (Exposed part) Ins

22、ulation tester (DC 500V) SAFETY PRECAUTIONSSAFETY PRECAUTIONSSAFETY PRECAUTIONSSAFETY PRECAUTIONSSAFETY PRECAUTIONS The following precautions should be observed when servicing. 1. Since many parts in the unit have special safety-related characteristics, always use genuine Hitachis replacement parts.

23、 Especially critical parts in the power circuit block should not be replaced with other makers. Critical parts are marked with in the circuit diagram and printed wiring board. 2. Before returning a repaired unit to the customer, the service technician must thoroughly test the unit to ascertain that

24、it is completely safe to operate without danger of electrical shock. RadioFans.CN 收音机爱 好者资料库 3 AX-F300 ? ? ? ? ? Reception frequency band:? (FM:87.5108.0MHz(100kHz step) AM:5201710kHz(10kHz step) ? (FM:87.50108.00MHz(50kHz step) MW:5221611kHz(9kHz step) LW:153281kHz(1kHz step) ? (FM:87.50108.00MHz(5

25、0kHz step) AM:5221611kHz(9kHz step) 5201710kHz(10kHz step) ? (FM:76.00108.00MHz(50kHz step) AM:5221629kHz(9kHz step) 5201710kHz(10kHz step) Rated output power:40 W + 40 W (6W/ohms, 1kHz, T.H.D. 10%) Audio input / output jacks:CD input jacks, TAPE input/output jacks, AUX input jacks, MD input/output

26、jacks, PRE OUT (MONO) jack, headphones jack Power supply:E,EBS: AC 230 V, 50 Hz UC: AC 120 V, 60 Hz W,WUN : AC 110127 V, 50/60 Hz AC 220240 V, 50/60 Hz Power consumption:74 W (ECO-ON mode : 0.8 W) Maximum external dimensions: 210 (W) 96.5 (H) 350 (D) mm (including feet, controls and terminals) Weigh

27、t:4.5 kg ? ? ? ? Sampling frequency:44.1kHz Optical source:Semiconductor Power supply:E,EBS: AC 230 V, 50 Hz UC: AC 120 V, 60 Hz W,WUN : AC 110127 V, 50/60 Hz AC 220240 V, 50/60 Hz Power consumption:12 W Maximum external dimensions: 210 (W) 96.5 (H) 340 (D) mm (including feet, controls and terminals

28、) Weight:3.2 kg ? ? ? System:2 way BASS Reflex Speaker System Woofer:10 cm 1 Tweeter:5 cm 1 Impedance:6 ohms Maximum external dimensions: 150 (W) 275 (H) 227 (D) mm Weight:3.0 kg (1 speaker) ? ? System:Digital Quartz Clock Display Format:12-hour cycle (UC DEST) 24-hour cycle (other DEST) Timer Accur

29、acy:Within 60 seconds at monthly rate ? ? Remote control system:Infrared pulse Power supply:Two DC 1.5V R6P/AA batteries Maximum external dimensions: 54 (W) 27 (H) 172.5 (D) mm Weight:145g (including batteries) ? ? ? ? ? Type:MiniDisc digital audio system Wow & flutter:Below measurable limits (0.001

30、% W. peak or less) Sampling frequency:44.1 kHz Recording method:Magnetic modulation overwriting Light source:Semiconductor Laser Power supply:E,EBS: AC 230 V, 50 Hz UC: AC 120 V, 60 Hz W,WUN : AC 110127 V, 50/60 Hz AC 220240 V, 50/60 Hz Power consumption:14 W Maximum external dimensions: 210 (width)

31、 96.5 (height) 320 (depth) mm (including feet, controls and terminals) Weight:2.6 kg Specifications are subject to change or performance improvement without notice. RadioFans.CN 收音机爱 好者资料库 4 AX-F300 ? ? ? ? ? ? ? ? ? (1) Remove 2 screws from both sides. (2) Remove 5 screws from the rear plate. ? ? ?

32、 (1) Remove 4 screws from the bottom side of the front panel. (2) Remove 2 screws from both sides. (3) Remove screw to remove the ground wire. (E DEST ONLY). (4) Remove the connectors , , and . (5) Remove the Front Panel by releasing the pawl on both sides. ?!? ?!? ?#?$?%? 5 AX-F300 &? ? (1) Remove

33、9 screws from the rear panel. (2) Remove the connector . ? ? ?(?)?* (1) Remove 2 screws and then the tone P . W. board. (2) Remove the volume knob assy, remove the nut and remove the volume P. W. board. (3) Remove 9 screws . +? ?,?(?)?* (1) Lift up the TU P . W. board and remove it from the main P.

34、W. board. (2) Remove 2 screws from the top side of the main P. W. board. (3) Remove 4 screws from the bottom side of the chassis. (4) Remove the 4 P . W. board holders from the chassis via the bottom side of the chassis. ?(?-?* ? ? ?. 6 AX-F300 ? ? ?/? ? ? ? ? (1) Remove 2 screws from both sides. (2

35、) Remove 3 screws from the rear panel. ? ? ? (1) Remove 2 screws from both sides. (2) Remove 3 screws from the bottom side of the front panel. (3) Remove the Front Panel by releasing the pawl on both sides. (4) Remove the flat cable from the main P . W. board. &? ? (1) Remove 7 screws from the rear

36、panel. ?!? ?!? 7 AX-F300 ? ?01?,0?, ?22?-?34?,?(?)?*?*? ?(?)?* (1) Remove one each of screws and from the main P. W. board on the side. (2) Remove 2 screws from the top side of the mechanical unit. (3) Remove 2 screws from the bottom side of the chassis. (4) Remove the connectors , , and of the main

37、 P . W. board. (5) Remove the connector of the P . T. P . W. board. (6) Remove 1 screw from the top side of the P . T. cover and detach the power transformer from the chassis. (7) Remove 1 screw of the ground wire. (8) Remove the connectors , and of the motor P. W. board from the main P. W. board. (

38、9) Remove 2 screws from the motor P . W. board. (10)Remove the solder from the four places of the soldering section of the motor. (11)Remove the connectors PG402 and 403 of the motor P . W. board. ?/? ?/?& 8 AX-F300 ? ? ?#? ?$? ?+? ? ? ? (1) Remove 2 screws from both sides. (2) Remove 6 screws from

39、the rear panel. ? ? ? (1) Remove 2 screws from both sides. (2) Remove 4 screws from the bottom side of the front panel. (3) Remove the Front Panel by releasing the pawl on both sides. (4) Remove the flat cable from the main P . W. board. &? ? (1) Remove 7 screws from the rear panel. ? ?)? ?!? ?!? 9

40、AX-F300 ? ?01?,0?, ?22?-?3 (1) Remove 4 screws . (2) Remove the flat cable from the main P . W. board. +? ?,?(?)?* (1) Lift up the I/O P . W. board and remove if from the main P. W. board. (2) Remove 6 screws . ? ?)? ?5$?(?)?* 10 AX-F300 ? ? ? ? ? ? DC voltmeter Screwdrivers for adjustments ? !#$% N

41、ote: Making adjustments without performing the following setting may result in damage of power transistors. (1) Power switch: OFF (2) Volume knob: MIN (3) Function switch: AUX (4) Speaker: Open (5) VR502L/R: Minimum % ? &? ? (1) Connect the DC voltmeter to PG502. (Refer to the connection diagram.) (

42、2) Turn on the power and adjust VR502L (on the left) and VR502R (on the right) so that the measured value of the voltme- ter can be within the range of 2 0.5 mV. PRE AMP PWB PG502 DC VoltmeterDC Voltmeter + VR502RVR502L 11 AX-F300 ? ? ? W004(ORG) W006 (BRN) W007 (BRK) W002(GRY) W010(YEL) P2B PG001 P

43、3A CN504 SPEAKER PWB VOLTAGE SELECTOR P.W.B (W/WUN ONLY) *10A *P9A *P8B CN505 *P4A/P6A CN505 P2A PG003PG002 MAIN PWB PG504 CN502ACN501A CN101B PG402 CN103B CN104B PG301 *P4B/ P7A *P5AP3B CN002CN003 P10BP9BP8B P5BP6BP7B PT PWB CN104ACN103A W415 W001 DISP PWB CN101A TU PWB CN502BCN501B PG503 CN503 CN401 CN402 VOLUME PWB PG