Jvc-KDDV-6101-Service-Manual(1) 电路图 维修手册.pdf

《Jvc-KDDV-6101-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-KDDV-6101-Service-Manual(1) 电路图 维修手册.pdf（43页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2005 Victor Company of Japan, Limited No.MA154 2005/2 DVD/CD RECEIVER MA15420052 KD-DV6101,KD-DV6107 TABLE OF CONTENTS 1PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2、-3 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、1-7 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. . . . . 1-29 Area suffix E - Southern Europe EU - Turkey KD-DV6101 Area suffix EE - Russian Federation KD-DV6107 KD-DV6101 KD-DV6107 KD-DV6101KD-DV6107 Steering wheel remote controller FM frequency rangeFM 87.5 MHz to 108.0 MHz FM1/FM2 87.5 MHz to 108.0 MHz FM3 65.00 MHz to 74.00MHz RadioFans.CN 收

5、音机爱 好者资料库 1-2 (No.MA154) SPECIFICATION Design and specifications are subject to change without notice. AUDIO AMPLIFIER SECTION Maximum Power OutputFront50 W per channel Rear50 W per channel Continuous Power Output (RMS) Front19 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 0.8% total har

6、monic distortion. Rear19 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Load Impedance4 (4 to 8 allowance) Equalizer Control RangeFrequencies60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz Level10 dB Signal-to-Noise Ratio70 dB Audio Output LevelAnalog

7、(2nd AUDIO OUT)6 mW (at 16 ) Digital (DIGITAL OUT: Optical)Signal wave length : 660 nm Output level : -21 dBm to -15 dBm Line-Out Level/Impedance5.0 V/20 k load (full scale) Output Impedance1 k Subwoofer-Out Level/Impedance2.0 V/20 k load (full scale) Color SystemPAL Video Output (composite)1 Vp-p/7

8、5 Other TerminalsLINE IN, CD changer TUNER SECTION Frequency RangeFM87.5 MHz to 108.0 MHz FM1/FM2 (only KD-DV6107)87.5 MHz to 108.0 MHz FM3 (only KD-DV6107)65.00 MHz to 74.00 MHz AM(MW) 522 kHz to 1 620 kHz (LW) 144 kHz to 279 kHz FM TunerUsable Sensitivity11.3 dBf (1.0 V/75 ) 50 dB Quieting Sensiti

9、vity16.3 dBf (1.8 V/75 ) Alternate Channel Selectivity (400 kHz) 65 dB Frequency Response40 Hz to 15 000 Hz Stereo Separation35 dB Capture Ratio1.5 dB MW TunerSensitivity20 V Selectivity35 dB LW TunerSensitivity50 V DVD/CD PLAYER SECTION Signal Detection SystemNon-contact optical pickup (semiconduct

10、or laser) Number of Channels2 channels (stereo) Frequency ResponseDVD, fs=48 kHz/96 kHz16 Hz to 22 000 Hz VCD, CD, MP3, WMA16 Hz to 20 000 Hz Dynamic Range96 dB Signal-to-Noise Ratio98 dB Wow and FlutterLess than measurable limit MP3 (MPEG Audio Layer 3)Max. Bit Rate: 320 kbps WMA (Windows Media Aud

11、io)Max. Bit Rate: 192 kbps GENERAL Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance) Grounding SystemNegative ground Allowable Operating Temperature0C to +40C Dimensions (W H D)Installation Size (approx.)182 mm 52 mm 158 mm Panel Size (approx.)188 mm 58 mm 11 mm Mass (approx.)1.7

12、kg (excluding accessories) RadioFans.CN 收音机爱 好者资料库 (No.MA154)1-3 SECTION 1 PRECAUTIONS 1.1Safety Precautions ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. ! Please use enough cautio

13、n not to see the beam directly or touch it in case of an adjustment or operation check. RadioFans.CN 收音机爱 好者资料库 1-4 (No.MA154) 1.2Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser di

14、ode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in

15、the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any sta

16、tic electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer t

17、o the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.3Handling the traverse unit (optical pickup) (1) Before disconnecting the flexible wire from the connector CN101 on the mechanism

18、control board, solder the short-circuit points on the flexible wire. Caution: If you do not follow this instruction, the DVD pickup may be damaged. (2) Disconnect the flexible wire from the connector CN101 on the mechanism control board. (3) Remove the solders from the short-circuit points on the fl

19、exible wire after replacing the DVD pickup. (4) Connect the flexible wire to the connector CN101 on the mechanism control board. 1M (caption) Anti-static wrist strap Conductive material (conductive sheet) or iron plate Mechanism control board CN101 Flexible wire Short-circuit points (No.MA154)1-5 1.

20、4Important for laser products 1.CLASS 1 LASER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit

21、if it malfunctions. 4.CAUTION : The CD,MD and DVD player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : I

22、f safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS ! Please use enough caution not to see the beam direc

23、tly or touch it in case of an adjustment or operation check. WARNING LABEL CAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e) VARNING : Synlig och osynling laserstrlning nr den ppnas och sprren r urkopplad. Betrakta ej strle

24、n. (s) VARO : Avattaessa ja suojalukitus ohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmlle lasersteilylle. Vlt steen kohdistumista suoraan itseesi. (f) ADVARSEL : Synlig og usynlig laserstrling nr maskinen er ben eller interlocken fejeler. Undg direkte eksponering til strling. (d) CLASS

25、1 LASER PRODUCT 1-6 (No.MA154) SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. (No.MA154)1-7 SECTION 3 DISASSEMBLY 3.1Main body section 3.1.1Removing the front panel assembly (See Fig.1) Push the detach button in the lower left part of the

26、 front panel as- sembly and remove the front panel assembly. Fig.1 3.1.2Removing the bottom cover (See Fig.2) Reference: Remove the front panel assembly as required. (1) Release the two joints a, two joints b and joint c. (2) Remove the bottom cover from the main body. Caution: Do not damage the mai

27、n board when releasing the joints using a screwdriver or a similar tool. Fig.2 Front panel assembly Detach button Bottom cover b b a a c 1-8 (No.MA154) 3.1.3Removing the front chassis assembly (See Figs.3 and 4) Remove the front panel assembly and bottom cover. (1) From the front side of the main bo

28、dy, remove the two screws A attaching the front chassis assembly. (See Fig.3.) (2) From the both sides of the main body, remove the two screws B attaching the front chassis assembly. (See Fig.4.) (3) Release the two joints d and two joints e. (See Fig.4.) Fig.3 Fig.4 3.1.4Removing the side heat sink

29、 (See Fig.5) Reference: Remove the front panel and front chassis assemblies as re- quired. From the left side of the main body, remove the two screws C and three screws D attaching the side heat sink. Fig.5 A Front chassis assembly d d Front chassis assembly B e e B C D Side heat sink (No.MA154)1-9

30、3.1.5Removing the rear bracket (See Fig.6) Remove the bottom cover. (1) From the back side of the main body, remove the two screws E, two screws E, screw E, screw F, two screws G and three screws H attaching the rear bracket. Reference: Screw E is used for KD-DV6101 only. (2) Remove the LINE IN, SUB

31、WOOFER and AUDIO OUT ca- bles from the rear bracket in the direction of the arrow. Reference: When attaching the LINE IN and SUBWOOFER cables, in- sert them in the slots of the rear bracket and hang them on a wire holder. When attaching the screws E and screw E , attach the ca- ble holders with them

32、. 3.1.6Removing the main board (See Figs.6 and 7) Remove the front panel assembly, bottom cover, front chassis assembly and side heat sink. Reference: Remove the rear bracket as required. (1) From the back side of the main body, remove the three screws H attaching the main board. (See Fig.6.) (2) Fr

33、om the bottom side of the main body, remove the three screws J attaching the main board. (See Fig.7.) (3) Disconnect the connector CN961 on the main board from the DVD mechanism assembly and take out the main board from the main body. (See Fig.7.) Fig.6 Fig.7 3.1.7Removing the DVD mechanism assembly

34、 (See Fig.8) Remove the front panel assembly, bottom cover, front chassis assembly, side heat sink and main board. (1) From the inside of the top chassis, remove the three screws K attaching the DVD mechanism assembly. (2) Take out the DVD mechanism assembly from the top chas- sis. Fig.8 Rear bracke

35、t G H E Cable holders F H H E E Cable holder Wire holder Slot LINE IN cable Rear bracket E SUBWOOFER cable AUDIO OUT cable Slot E CN961 J J Main board J K K K DVD mechanism assembly Top chassis 1-10 (No.MA154) 3.1.8Removing the main sub board (See Figs.9 to 11) Remove the front panel assembly, botto

36、m cover, front chassis assembly, side heat sink, main board and DVD mechanism as- sembly. (1) From the top side of the DVD mechanism assembly, re- move the two screws L attaching the dust cover. (See Fig.9.) (2) Remove the dust cover from the DVD mechanism assem- bly. (See Fig.9.) Reference: When at

37、taching the dust cover, align the joints f in the holes of the dust cover before attaching the screws L. (See Fig.9.) (3) Release the lock of the connector CN962 on the main sub board and disconnect the card wire. (See Fig.10.) (4) Bend the joint g in the direction of the arrow. (See Fig.10.) (5) Re

38、move the two screws M attaching the main sub board and remove the main sub board from the DVD mechanism assembly. (See Fig.10.) Reference: When attaching the main sub board, align the joints h in the holes of the main sub board before attaching the screws M. (See Fig.10.) When the resolution of DVD

39、mechanism assembly is done sequentially, remove the two screws N attaching the support bracket. (See Fig.11.) Remove the card wire from the connector CN401 as re- quired. (See Fig.11.) Fig.9 Fig.10 Fig.11 L L DVD mechanism assembly Dust cover f f Card wire g M h h CN962 Lock Main sub board DVD mecha

40、nism assembly Card wire N Support bracket CN401 (No.MA154)1-11 3.1.9Removing the switch board (See Figs. 12 to 14) Remove the front panel assembly. (1) From the back side of the front panel assembly, remove the five screws P attaching the rear cover. (See Fig.12.) (2) Release the ten joints i attach

41、ing the rear cover to the front panel assembly. (See Fig.13.) (3) Take out the switch board while lifting the switch board from the front panel assembly little by little. (See Fig.14.) Reference: Remove the volume knob from the front side of the front panel assembly at the same time. Note: Do not lo

42、se the compression springs when removing the switch board. (See Fig.14.) Fig.12 Fig.13 Fig.14 P P Rear cover Front panel assembly P i i Rear cover i i Switch board Front panel assembly Compression spring Compression spring 1-12 (No.MA154) 3.2DVD mechanism assembly 3.2.1Removing the mechanism control

43、 board (See Fig.1) Caution: Before disconnecting the flexible wire extending from the DVD pickup, solder the short-circuit point on the flexible wire using a grounding soldering iron. If you do not follow this instruction, the DVD pickup may be damaged. (1) Turn over the body, and solder the short-c

44、ircuit points on the flexible wire extending from the DVD pickup. (2) Disconnect the flexible wire from connector CN101 on the mechanism control board. (3) Disconnect the card wire from connector CN201 on the mechanism control board. (4) Disconnect the flexible wire from connector CN202 on the mecha

45、nism control board. (5) Unsolder two soldered points a on the mechanism control board and remove the wire extending from the feed motor. (6) Remove the screw A attaching the lug wire. (7) Remove the two screws B and screw C attaching the mechanism control board. Caution: As the flexible wire to be c

46、onnected to CN101, make sure to attach it to the mechanism control board using a double tape. After reassembling, unsolder the short-circuit points. Fig.1 Double tape Feed motor Mechanism control board CN202 CN101 B a C B CN201 Flexible wire Short-circuit points A Lug wire (No.MA154)1-13 3.2.2Removi

47、ng the top cover (See Fig.2) (1) Remove the two screws D attaching the top cover on the back of the body. (2) Remove the top cover upward. Reference: When reassembling, set part b of the top cover under the bending part c of the chassis frame. 3.2.3Removing the mechanism section (See Fig.2 to 4) Rem

48、ove the top cover. (1) From the bottom of the body, remove the screw E attaching the lug wire. (See Fig.2.) (2) Remove the two screws F attaching the right and left stop- pers on the front side. (See Fig.2.) (3) Remove the two floating springs on the bottom of the body. (See Fig.3.) (4) Move the mec

49、hanism section upward and remove from the chassis frame. The three damper springs come off from the dampers. (See Fig.4.) Caution: When reassembling, reattach the damper spring to the damper respectively and insert the three shafts on the bot- tom of the mechanism to the dampers. Before inserting the shaft to the dampers, apply IPA to the hole of damper. Fig.2 Fig.3 Fig.4 D Top cover Stopper Stopper F F b c E Lug wire D Floating spring Mechanism section Damper