Jvc-KDS-587-Service-Manual(1) 电路图 维修手册.pdf

《Jvc-KDS-587-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-KDS-587-Service-Manual(1) 电路图 维修手册.pdf（49页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL CD RECEIVER No.49741 Apr. 2002 COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD. KD-S587 KD-S587 Contents Safety precaution Preventing static electricity Disassembly method Adjustment method 1-2 1-3 1-4 1-11 Flow of functional operation unit TOC read Maintenance of laser pickup Replacement

2、 of laser pickup Description of major ICs 1-12 1-14 1-14 1-1528 Area Suffix UR - Brazil LOUD SEL DISP DIRECT TRACK ACCESS 7 RadioFans.CN 收音机爱 好者资料库 KD-S587 1-2 ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preformin

3、g repair of this system. Safety precaution ! Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check. RadioFans.CN 收音机爱 好者资料库 KD-S587 1-3 Front bracket CD mechanism control board Damper bracket CD mechanism assy FD screw Feed motor assy FD gear

4、Pickup unit Preventing static electricity 1.Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent th

5、is when performing repairs. 2.About the earth processing for the destruction prevention by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being perform

6、ed. 2-1 Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. 2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3

7、. Handling the optical pickup 1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) 2. Do not use a tester to

8、 check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 4.Handling the traverse unit (optical pickup) 1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the

9、 shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3.

10、 Handle the flexible cable carefully as it may break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it Conductive material (conductive sheet) or iron plate (caption) Anti-static wrist strap Soldering Attention when tr

11、averse unit is decomposed 1.Solder is put up before the card wire is removed from connector on the CD substrate as shown in Figure. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.) 2.Please remove solder after connecting the card wire with when you install

12、 picking up in the substrate. *Please refer to Disassembly method in the text for pick-up and how to detach the substrate. RadioFans.CN 收音机爱 好者资料库 KD-S587 1-4 Press the eject button in the lower right part of the front panel. Remove the front panel assembly from the body. 1. Removing the front panel

13、 assembly (See Fig.1) Prior to performing the following procedure, remove the front panel assembly. Release the four joint tabs a on both sides of the front chassis assembly and remove the front chassis assembly toward the front. 1. Removing the front chassis assembly (See Fig.2 and 3) Disassembly m

14、ethod Fig.1 Fig.2 Fig.3 Front panel assembly Eject button Tab a Tab a Front chassis assembly Front chassis assembly Heat sinkTab a Tab a KD-S587 1-5 Remove the three screws A on the left side of the body. 1. Removing the heat sink (See Fig.4) Prior to performing the following procedure, remove the f

15、ront panel assembly, the front chassis assembly and the heat sink. Turn over the body and unjoint the five joints b with the bottom cover and the body using a screwdriver. 1. Removing the bottom cover (See Fig.5 and 6) Fig.4 Fig.5 Fig.6 Heat sink AA Joints b Joints b Joint b Joints b Joints b Joint

16、b Bottom cover Bottom cover Rear panel Rear panel KD-S587 1-6 Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly, the heat sink and the bottom cover. Remove the screw B, the four screws C and the three screws D attaching the rear bracket on the b

17、ack of the body. Remove the rear panel. Remove the two screws E attaching the main board on the bottom of the body. Disconnect connector CN501 on the main board in the direction of the arrow. 1. 2. Removing the main board (See Fig.7 and 8) Prior to performing the following procedure, remove the fron

18、t panel assembly, the front chassis assembly, the heat sink, the bottom cover and the main board. Remove the three screws F attaching the cassette mechanism section on the back of the top chassis. 1. Removing the CD mechanism section (See Fig.9) Fig.7 Fig.8 Fig.9 Rear panel B D D D C Main board E E

19、CN501 CD mechanism section F F F Top chassis CC KD-S587 1-7 Prior to performing the following procedure, remove the front panel assembly. Remove the four screws G attaching the rear cover on the back of the front panel assembly. Unjoint the nine joints c with the front panel and the rear cover. Remo

20、ve the control switch board on the back of the front panel. 1. 2. 3. Removing the control switch board (See Fig.10 to 12) Fig.10 Fig.11 Fig.12 G GG G Rear cover Joints c Joints c Front panel Rear cover Front panel Control switch board Joints c Joints c KD-S587 1-8 Unsolder the part f and g on the CD

21、 mechanism control board. Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part). Remove the screw F attaching the CD mechanism control board. Remove the CD mechanism control board in the direction of the arrow while re

22、leasing it from the two damper bracket slots i and the front bracket slot j. Disconnect the flexible wire from connector on the pickup unit. Removing the CD mechanism control board(See Fig.1 and 2) Turn the FD gear in the direction of the arrow to move the entire pickup unit to the appropriate posit

23、ion where the flexible wire of the CD mechanism unit can be disconnected easily (Refer to Fig.2). ATTENTION: Fig.1 Fig.2 Fig.3 Fig.4 Front bracket CD mechanism control board Shift the lock Flexible wire Pickup unit FD gear CD mechanism control board Loading motor Front bracket Front bracket Pull out

24、ward Pull outward Flame Damper bracket m m h i g f II I CD mechanism assy F j k G k G KD-S587 1-9 Prior to performing the following procedure, remove the CD mechanism control board. Remove the two springs k attaching the CD mechanism assy and the front bracket. Remove the two screws G and the front

25、bracket while pulling the flame outward. Remove the belt and the screw H from the loading motor. Removing the loading motor (See Fig.3 to 5) Prior to performing the following procedure, remove the CD mechanism control PWB and the front bracket (loading motor). Remove the three screws I and the dampe

26、r bracket. Raise the both sides fix arms and move the fix plates in the direction of the arrow to place the four shafts l as shown in Fig.8 and 9. Remove the CD mechanism assy and the two springs m attaching the flame. Remove the two screws J and both sides rear damper brackets from the dampers. Det

27、ach the CD mechanism assy from the left side to the right side. 1. 2. 3. 4. Removing the CD mechanism assy (See Fig.1, 6 to 9) The CD mechanism assy can be removed if only the rear damper bracket on the left side is removed. ATTENTION: Fig.5 Fig.6 Fig.7 Fig.8 Fig.9 Rear damper bracket Fix arm (R) Da

28、mper H II Loading motor Belt Damper bracket CD mechanism assy Flame m m I I Fix plate (L) l l Rear damper bracket Fix arm (L) Damper J Fix plate(R) J l l KD-S587 1-10 Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor) and the CD mech

29、anism assy. Remove the two screws K and the feed motor assy.1. Removing the feed motor assy (See Fig.10) *Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism assy and the feed motor assy. Detach the FD gear part of t

30、he pickup unit upward. Then remove the pickup unit while pulling out the part n of the FD screw. 1. Remove the screw L attaching the nut push spring plate and the pickup mount nut from the pickup unit. Pull out the FD screw. 2. Removing the pickup unit (See Fig.10 and 11) When reattaching the pickua

31、p unit, reattach the part o of the pickup unit, then the part n of the FD screw. ATTENTION: Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism assy and the feed motor assy. Turn up the CD mechanism assy and remove t

32、he two springs p on both sides of the clamper arms. Open the clamper arm upward. Turn the turn table, and remove the two screws M and the spindle motor. 1. 2. Removing the spindle motor (See Fig.12 and 13) Fig.10 Fig.11 Fig.12 Fig.13 Spindle motor pp Pickup unit Part n FD screw Feed motor assy FD ge

33、arPickup unit Part O K Nut push spring plate Pickup mount nut Pickup unit FD screw L M M KD-S587 1-11 Adjustment method Test instruments required for adjustment 1. Digital oscilloscope (100MHz) 2. AM Standard signal generator 3. FM Standard signal generator 4. Stereo modulator 5. Electric voltmeter

34、6. Digital tester 7. Tracking offset meter 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Standard measuring conditions Power supply voltage DC14.4V(10.516V) Load impedance 4 (2 Speakers connection) Line out load impedance 20k Output Level Line out 2.0V (Vol. MAX) How to conn

35、ect the extension cable for adjusting Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since direct reading of figures are applied in this working standard. Standard volu

36、me position Balance and Bass Digital: 0) RF signal Flow of functional operation until TOC read When the pickup correctly moves to the inner area of the disc TERMINAL Microprocessor commands FMO TC9462 53 FEED MOTOR +TERMINAL IC581 5 REST SW When the disc correctly rotates Tracking Servo Loop ON Serv

37、o CLV Rough Servo AccelerationAccelerationAcceleration Microprocessor commands Spindle motor (-) IC581 7 0.5 Sec 0.5 Sec KD-S587 1-13 Feed Section Focus Section Tracking Section Spindle Section Is the voltage output at IC521 pin 53 5V or 0V? Check the feed motor. Is 4V present at both sides of the f

38、eed motor? Is the wiring for IC521 (90) (100) correct? Check IC581. Is 6V or 2V present at IC581 5 and 6? Is 5V present at IC581 pin 11? Check the feed motor connection wiring. Check the vicinity of IC521. Check CD 9V and 5V. YES YES YES NONO NO NO NO YES YES When the lens is moving: Check the circu

39、its in the vicinity of IC581 pins 15 18. Check the pickup and its connections. NO YES YES YES Does the S-search waveform appear at IC581 pins 17 and 18? Is the disk rotated? Does the RF signal appear at TP1? Is 4V present at IC581 pins 7 and 8 ? Check the spindle motor and its wiring. Is 4V present

40、at IC521 pin 55 ? Check the vicinity of IC581. Check IC501 and IC521. YES NO NO NO NONO YES YES YES Check the circuits in the vicinity of IC501 19 24 or the pickup Is the RF waveform at TP1 distorted? Proceed to the Tracking section When the disc is rotated at first: Check the circuit in the vicinit

41、y of IC501 pins 2 12. Check IC521. Check the pickup and its connections. YESYES YES Is the tracking error signal output at IC501 12? Approx. 1.2 V 4V KD-S587 1-14 Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soa

42、ked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear. (1) The level of RF output (EFM output:ampli tude of eye pattern) will be low. Replacement of laser pickup Is RF output 1.0 0.35Vp-p? Replace it. NO YES O.K (3) Semi-fixed r

43、esistor on the APC PC board The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the laser power.Since this adjustment should be performed to match the characteristics of the whole optical block, do not touch the semi-fixed resistor. If the laser

44、 power is lower than the specified value,the laser diode is almost worn out, and the laser pickup should be replaced. If the semi-fixed resistor is adjusted while the pickup is functioning normally,the laser pickup may be damaged due to excessive current. Turn off the power switch and,disconnect the

45、 power cord from the ac outlet. Replace the pickup with a normal one.(Refer to Pickup Removal on the previous page) Plug the power cord in,and turn the power on. At this time,check that the laser emits for about 3seconds and the objective lens moves up and down. Note: Do not observe the laser beam d

46、irectly. Play a disc. Check the eye-pattern at TP1. Finish. KD-S587 1-15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 S48 S47 S46 S45 S44 S43 S42 S41 S40 S

47、39 S38 S37 S36 S35 S34 S33 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 S17 S18 S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 S29 S30 S31 S32 DI CL CE OSC Vss VDD2 VDD1 INH VDD COM3 COM2 COM1 S52 S51 S50 S49 LC75823W (IC601) : LCD driver 1. Pin Layout & Symbol 2. Pin Function Pin No. 1 to 52 53 to 55 5

48、6 57 58 59 60 61 62 63 64 I/O O O - I I I - I/O I Segment output pins used to display data transferred by serial data input. Common driver output pins. The frame frequency is given by : t0=(fosc/384)Hz. Power supply connection. Provide a voltage of between 4.5 and 6.0V. Display turning off input pin

49、. INT=L (Vss) - off (S1 to S52, COM1 to COM3=L INT=H (VDD)- on Serial data can be transferred in display off mode. Used for applying the LCD drive 2/3 bias voltage externally. Must be connected to VDD2 when a 1/2 bias drive scheme is used. Used for applying the LCD drive 1/3 bias voltage externally. Must be connected to VDD1 when a 1/2 bias drive scheme is used. Power supply connection. Connect to