Jvc-KSAX-6700-Service-Manual(1) 电路图 维修手册.pdf
《Jvc-KSAX-6700-Service-Manual(1) 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Jvc-KSAX-6700-Service-Manual(1) 电路图 维修手册.pdf(25页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL KS-AX6700KS-AX6700 No. 49559 Jun. 2000 KS-AX6700 POWER AMPLIFIER Printed in Japan 200006(S) (No. 49559) Contents Safety Precaution Location of main parts Removal of main parts Adjustment method Wire connection diagram 1-2 1-3 1-5 1-8 1-9 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRO
2、NICS DIVISION PERSONAL & MOBILE NETWORK B.U. 10-1,1Chome,Ohwatari-machi,Maebashi-city,Japan COPYRIGHT 2000 VICTOR COMPANY OF JAPAN, LTD. This service manual is printed on 100% recycled paper. Areas suffix Caution If electricity is connected during disassembly, it must be a no load current. If it is
3、load current, be sure to attach a heat sink to the power-amp IC. This will be damaged if the above precautions are not followed, as it does not have a sub heat sink attached to it. J - Nothem America E - Continental Europe RadioFans.CN 收音机爱 好者资料库 KS-AX6700 1-2 Safety precaution !CAUTION Burrs formed
4、 during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. RadioFans.CN 收音机爱 好者资料库 KS-AX6700 1-3 Location of main parts Volume knob Control panel Switch knob Heat sink Rear panel Input for power Fuse Output t
5、erminal Heat sink Front panel Low input(L) High input connector Heat sink Low input(R) RadioFans.CN 收音机爱 好者资料库 KS-AX6700 1-4 CCFL P.C. board Wire assemby (from Main) Main P.C. board GND wire Heat sink (Bottom view) Sub1 P.C. board Main P.C. board Sub2 P.C. board 2pin connector (to CCFL P.C. board) K
6、S-AX6700 1-5 From the bottom side of the main unit, remove the 4 screws A retaining the bottom cover. Then remove the 6 screws B retaining the bottom cover. Remove the bottom cover. 1. 2. 3. If electricity is connected during disassembly, it must be a no load current. If it is load current, be sure
7、to attach a heat sink to the power-amp IC. This will be damaged if the above precautions are not followed, as it does not have a sub heat sink attached to it. CAUTION: Removal of main parts Removing the bottom cover (see Fig. 1) Remove the bottom cover from the main unit. Loosen and remove the 2 scr
8、ews C retaining the top plate on the main unit. (Stoppers are attached to the backs of the C screws so that they cannot be removed easily.) 1. 2. Remove the 3 volume knobs on top of the control panel. If it cannot be pulled out easily, insert a scale or suitable lever between the base of the volume
9、knob and the control panel so that the volume knob is raised a little above the surface and then remove it. (Be careful when inserting a lever etc. not to scratch the surface of the control panel). Remove the 4 screws D retaining the control panel. Then detach the control panel and the switch knob.
10、3. 4. Removing the main P.C. board (see Fig. 2 to 8) (Side view) Scale or suitable lever D Top plate C Volume knob Control panel Bottom cover B Fig. 1 Fig. 3 Fig. 2 Fig. 4 A D C A B Volume knob Switch knob KS-AX6700 1-6 Remove the 6 screws E retaining the panels on both sides of the main unit. 5. To
11、 remove the wire assy, lift up the main P.C. board a little. 7. Remove the 13 screws F attaching the main P.C. board to the bottom of the main unit. (The GND wire that protrudes from the main P.C.board must be re-installed to its original position during re-assembly.) 6. Fig. 7 Fig. 5 GND wire Main
12、P.C. board Main P.C. board Wire assemby F F Rear panel E Fig. 6 Front panel E Fig. 8 (Side view) KS-AX6700 1-7 Remove the bottom cover. Then remove the Main P.C. board. From the bottom side of the main unit, remove the 4 screws G retaining the CCFL cover. 1. 2. 3. Then remove the insulation sheet on
13、 top of the CCFL P.C. board. 4. Remove the 4 screws H retaining the CCFL P.C. board. 5. Remove the CCFL P.C. board by sliding it a little towards the arrow mark. 6. Removing the CCFL board (see Fig. 9 to 12) Fig. 9 Fig. 10 CCFL cover G GG H CCFL P.C. board Insulation sheet Fig. 11 CCFL P.C. board H
14、Fig. 12 This section is cought by the portion. KS-AX6700 1-8 Adjustment method 1. . Check the voltage and frequency of the secondary toroidal coil. 2.Measure the secondary toroidal coil, if the standard frequency value of 24.35 kHz 10 Hz is not attained, measure the R760 terminal, then adjust the VR
15、701 so that the R760 terminal becomes 24.25 kHz 10Hz. Note: TEST SET FREQUENCY COUNTER MAIN PCB (+) (-) POWER SUPPLY 14.4V R760 Measuring Points 88Vp-p 2.5V DC/DC CONVERTER SECOND GENERATOR SWITCHING TEST ITEM VOLTAGE TEST FREQUENCY CHECK 88Vp-p2.5V 24.350KHz10Hz OSCILLOSCOPE VOLT/DIV: 10 TIME/DIV:
16、10mcec VARIABLE: MINIMUM SPECIFICATIONCONDITION FREQUENCY:24.35kHz 10Hz VOLTAGE VALUE:55Vp-p When measuring, adjust and apply power with no signal or load on each board. KS-AX6700 1-9 Wire connection diagram HIGH INPUT connector WHITE WHITE/BLACK GRAY GRAY/BLACK GND+12V CCFL PCB MAIN PCB CCFL L R RE
17、D BLACK SERVICE MANUAL KS-AX6700KS-AX6700 No. 49559 Jun. 2000 KS-AX6700 POWER AMPLIFIER Printed in Japan 200006(S) (No. 49559) Contents Safety Precaution Location of main parts Removal of main parts Adjustment method Wire connection diagram 1-2 1-3 1-5 1-8 1-9 VICTOR COMPANY OF JAPAN, LIMITED MOBILE
18、 ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK B.U. 10-1,1Chome,Ohwatari-machi,Maebashi-city,Japan COPYRIGHT 2000 VICTOR COMPANY OF JAPAN, LTD. This service manual is printed on 100% recycled paper. Areas suffix Caution If electricity is connected during disassembly, it must be a no load current. I
19、f it is load current, be sure to attach a heat sink to the power-amp IC. This will be damaged if the above precautions are not followed, as it does not have a sub heat sink attached to it. J - Nothem America E - Continental Europe KS-AX6700 2-1 Block diagram R-IN L-IN R L HI-INPUT INPUT AMP U101 -A
20、U101 -B U102 -A U102 -B U106 -A U206 -A VR103A VR103B U103 -A U103 -B U104 -A U104 -B VR102A VR102B U105 -A U105 -B SW101A SW101B LPF HPF OFF LPF HPF OFF Q142-Q146 Q148,Q149 Q152 Q161-Q166 R-OUT L-OUT POWER INPUT +12V D.C. REM F01,F02 Q701 Q702 U701 POWER CONTROL Q730,Q731 Q745-Q747 Q755-Q757 POWER
21、REGULATOR T1 U703 U704 TRANS & REGULATOR +/-15V VCC VEE Q150 Q250 MUTE CONTROL Q705 -708 Q171-Q176 Q272 PROTECT VR101B VR101A VR102C VR102D 7 6 22 11 6 7 POWER AMP Q790 CCFL+12V INVERTER LOAD CCFL board Q780 VR701 Q242-Q246 Q248,Q249 Q252 Q261-Q266 BOOST 0-12dBCROSSOVER 31 3 1 3 1 6 7 3 157 3 1 2 1
22、2 1 5 7 6 7 6 7 VARIABLE/INV.CIRCUIT(Gain1)/Amplifier 50-250Hz 12dB/OCT VARIABLE 6 5 4 3 2 1 BCDEFGHIJA 7 KS-AX6700 2-2 Caution If electricity is connected during disassembly, it must be a no load current. If it is load current, be sure to attach a heat sink to the power-amp IC. This will be damaged
23、 if the above precautions are not followed, as it does not have a sub heat sink attached to it. Indicates main signal Standard schematic diagrams Main board and sub 1/2 /sub2 board circuit diagram SUB2 PCB SUB1 PCB 6 5 4 3 2 1 BCDEFGHIJA 7 KS-AX6700 2-3 Caution If electricity is connected during dis
24、assembly, it must be a no load current. If it is load current, be sure to attach a heat sink to the power-amp IC. This will be damaged if the above precautions are not followed, as it does not have a sub heat sink attached to it. Main board 2/2 and CCFL board circuit diagram CCFL PCB Parts are safet
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Jvc-KSAX-6700-Service-Manual1 电路图 维修手册 Jvc KSAX 6700 Service Manual 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


