Jvc-KDR-467-EE-Service-Manual(1) 电路图 维修手册.pdf

《Jvc-KDR-467-EE-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-KDR-467-EE-Service-Manual(1) 电路图 维修手册.pdf（93页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2015 JVC KENWOOD Corporation No.MA596 2015/7 CD RECEIVER MA59620157 SERVICE MANUAL KD-R460J, KD-R461DA9, KD-R461E, KD-R461EN, KD-R461EY, KD-R461MA9, KD-R461U, KD-R461UT, KD-R462E, KD-R462EN, KD-R462EY, KD-R463EU, KD-R464E, KD-R464EN, KD-R466U, KD-R467EE, KD-R469E, KD-R469EY,

2、 KD-R469UR, KD-R660J, KD-R661E, KD-R661EN, KD-R661EY, KD-R661MA9, KD-R661U, KD-R661UT, KD-SR41J, KD-SR61J COPYRIGHT 2015 JVC KENWOOD Corporation Lead free solder used in the board (material: Sn-Ag-Cu, melting point: 219 Centigrade) Lead free solder used in the board (material: Sn-Cu, melting point:

3、230 Centigrade) DETACHABLE PANEL Mounting sleeve (GE20362-002A) DC cord (QAM1329-001) DC cord (QAM1345-003) (QAM1378-001) Trim plate (GE20363-00 xA) Escutcheon (B0H-0021-00) Remote control unit (RM-RK52M) Carrying case (GE40521-001A) ModelParts number KD-R460J KD-R461DA9 KD-R461E KD-R461EN KD-R461EY

4、 KD-R461MA9 KD-R461U KD-R461UT KD-R462E KD-R462EN KD-R462EY KD-R463EU KD-R464E KD-R464EN KD-R466U KD-R467EE KD-R469E KD-R469EY KD-R469UR KD-R660J KD-R661E KD-R661EN KD-R661EY KD-R661MA9 KD-R661U KD-R661UT KD-SR41J KD-SR61J CP-R460JD - CP-R461ED CP-R461ED CP-R461ED - CP-R461UD CP-R461UD CP-R462ED CP-

5、R462ED CP-R462ED CP-R463EU CP-R464ED CP-R464ED CP-R466UD CP-R467EED CP-R469ED CP-R469ED - CP-R660JD CP-R661ED CP-R661ED CP-R661ED - CP-R661UD CP-R661UD CP-SR41JD CP-SR61JD Hook (GE40685-001A) x2 DC cord assy (E3A-0181-00) DC cord assy (E3A-0218-00) Screw (M5x8) (QYSDSP5008ZA) x4 Screw (M5x10) (QYSDS

6、P5010ZA) x4 RadioFans.CN 收音机爱 好者资料库 (No.MA596)2/28 SPECIFICATION For US Subject to change without notice. TUNER FMFrequency Range87.9 MHz to 107.9 MHz (200 kHz step) 87.5 MHz to 108.0 MHz (50 kHz step) Channel Space Selection50 kHz/200 kHz Usable Sensitivity (S/N = 26 dB)8.2 dBf (0.71 V/75 ) Quietin

7、g Sensitivity(DIN S/N = 46 dB)17.2 dBf (2.0 V/75 ) Frequency Response (3 dB)30 Hz to 15 kHz Signal-to-Noise Ratio (MONO)64 dB Stereo Separation (1 kHz)40 dB AMFrequency Range530 kHz to 1 700 kHz (10 kHz step) 531 kHz to 1 611 kHz (9 kHz step) Channel Space Selection9 kHz/10 kHz Usable Sensitivity (S

8、/N = 20 dB)29 dB (28.2 V) CD player Laser DiodeGaAIAs Digital Filter (D/A)8 times over sampling Spindle Speed500 rpm - 200 rpm (CLV) Wow & FlutterBelow measurable limit Frequency Response (1 dB)20 Hz - 20 kHz Total Harmonic Distortion (1 kHz)0.01% Signal-to-Noise Ratio (1 kHz)105 dB Dynamic Range90

9、dB Channel Separation85 dB MP3 DecodeCompliant with MPEG-1/2 Audio Layer-3 WMA DecodeCompliant with Windows Media Audio USB USB StandardUSB 1.1, USB 2.0 (Full speed) Compatible DevicesMass storage class File SystemFAT12/ 16/ 32 Maximum Supply CurrentDC 5 V 1 A MP3 DecodeCompliant with MPEG-1/2 Audio

10、 Layer-3 WMA DecodeCompliant with Windows Media Audio WAV DecodeLinear-PCM Auxiliary Frequency Response (3 dB)20 Hz - 20 kHz Input Maximum Voltage1 000 mV Input Impedance30 k Audio Maximum Output Power50 W 4 or 50 W 2 + 50 W 1 (Subwoofer = 4 ) Full Bandwidth Power(at less than 1 % THD)22 W 4 Speaker

11、 Impedance4 to 8 Preout Level/Load (CD/USB)2 500 mV/10 k Preout Impedance 600 General Operating Voltage (10.5 V - 16 V allowable)14.4 V Maximum Current Consumption10A Operating Temperature Range0C to + 40C Installation Size (W H D)182 mm 53 mm 158 mm (7-3/16 2-1/8 6-1/4) Weight1.2 kg (2.65 lbs) Radi

12、oFans.CN 收音机爱 好者资料库 (No.MA596)3/28 SPECIFICATION For Europe Subject to change without notice. TUNER FMFrequency Range Except KD-R46787.5 MHz to 108.0 MHz (50 kHz step) Frequency Range KD-R467FM: 87.5 MHz to 108.0 MHz (50 kHz step) FM-Lo: 65.0 MHz to 74.0 MHz (30 kHz step) Usable Sensitivity (S/N = 2

13、6 dB)0.71 V/75 Quieting Sensitivity(DIN S/N = 46 dB)2.0 V/75 Frequency Response (3 dB)30 Hz to 15 kHz Signal-to-Noise Ratio (MONO)64 dB Stereo Separation (1 kHz)40 dB AMFrequency RangeMW : 531 kHz to 1 611 kHz (9 kHz step) LW : 153 kHz to 279 kHz (9 kHz step) Usable Sensitivity (S/N = 20 dB)MW : 28.

14、2 V LW : 50 V CD player Laser DiodeGaAIAs Digital Filter8 times over sampling Spindle Speed500 rpm - 200 rpm (CLV) Wow & FlutterBelow measurable limit Frequency Response (1 dB)20 Hz - 20 kHz Total Harmonic Distortion (1 kHz)0.01% Signal-to-Noise Ratio (1 kHz)105 dB Dynamic Range90 dB Channel Separat

15、ion85 dB MP3 DecodeCompliant with MPEG-1/2 Audio Layer-3 WMA DecodeCompliant with Windows Media Audio USB USB StandardUSB 1.1, USB 2.0 (Full speed) Compatible DevicesMass storage class File SystemFAT12/ 16/ 32 Maximum Supply CurrentDC 5 V 1 A MP3 DecodeCompliant with MPEG-1/2 Audio Layer-3 WMA Decod

16、eCompliant with Windows Media Audio WAV DecodeLinear-PCM Auxiliary Frequency Response (3 dB)20 Hz - 20 kHz Input Maximum Voltage1 000 mV Input Impedance30 k Audio Maximum Output Power50 W 4 or 50 W 2 + 50 W 1 (Subwoofer = 4 ) Full Bandwidth Power(at less than 1 % THD)22 W 4 Speaker Impedance4 to 8 P

17、reout Level/Load (CD/USB)2 500 mV/10 k load (full scale) Preout Impedance 600 General Operating Voltage14.4 V (10.5 V - 16 V allowable) Maximum Current Consumption10A Operating Temperature Range0C to + 40C Installation Size (W H D)182 mm 53 mm 158 mm Weight1.2 kg RadioFans.CN 收音机爱 好者资料库 (No.MA596)4/

18、28 For ASIA Subject to change without notice. TUNER FMFrequency Range87.5 MHz to 108.0 MHz (50 kHz step) Usable Sensitivity (S/N = 26 dB)8.2 dBf (0.71 V/75 ) Quieting Sensitivity(DIN S/N = 46 dB)17.2 dBf (2.0 V/75 ) Frequency Response (3 dB)30 Hz to 15 kHz Signal-to-Noise Ratio (MONO)64 dB Stereo Se

19、paration (1 kHz)40 dB AMFrequency RangeBand 1 (MW): 531 kHz to 1 611 kHz (9 kHz step) Band 2 (SW1): 2 940 kHz to 7 735 kHz (5 kHz step) Band 3 (SW2): 9 500 kHz to 10 135 kHz (5 kHz step) / 11 580 kHz to 18 135 kHz (5 kHz step) Channel Space SelectionBand 1: 9 kHz Band 2/3: 5 kHz Usable Sensitivity (

20、S/N = 20 dB)29 dB (28.2 V) SW: 30 dB (32 V) CD player Laser DiodeGaAIAs Digital Filter (D/A)8 times over sampling Spindle Speed500 rpm - 200 rpm (CLV) Wow & FlutterBelow measurable limit Frequency Response (1 dB)20 Hz - 20 kHz Total Harmonic Distortion (1 kHz)0.01% Signal-to-Noise Ratio (1 kHz)105 d

21、B Dynamic Range90 dB Channel Separation85 dB MP3 DecodeCompliant with MPEG-1/2 Audio Layer-3 WMA DecodeCompliant with Windows Media Audio USB USB StandardUSB 1.1, USB 2.0 (Full speed) Compatible DevicesMass storage class File SystemFAT12/ 16/ 32 Maximum Supply CurrentDC 5 V 1 A MP3 DecodeCompliant w

22、ith MPEG-1/2 Audio Layer-3 WMA DecodeCompliant with Windows Media Audio WAV DecodeLinear-PCM Auxiliary Frequency Response (3 dB)20 Hz - 20 kHz Input Maximum Voltage1 000 mV Input Impedance30 k Audio Maximum Output Power50 W 4 or 50 W 2 + 50 W 1 (Subwoofer = 4 ) Full Bandwidth Power(at less than 1 %

23、THD)22 W 4 Speaker Impedance4 to 8 Preout Level/Load (CD)2 500 mV/10 k load Preout Impedance 600 General Operating Voltage (10.5 V - 16 V allowable)14.4 V Maximum Current Consumption10A Operating Temperature Range0C to + 40C Installation Size (W H D)182 mm 53 mm 158 mm Weight1.2 kg (No.MA596)5/28 SE

24、CTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacemen

25、t parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions wi

26、ll void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not eviden

27、t from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical comp

28、onents having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may cre

29、ate shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is req

30、uired, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the r

31、epairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3

32、Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB d

33、iagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except t

34、he J and C version) 1.5Remote control The Lithium battery is in danger of explosion if replaced incor- rectly. Replace it only with the same or equivalent type. 1.6Preventing static electricity Electrostatic discharge (ESD), which occurs when static electric- ity stored in the body, fabric, etc. is

35、discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to pre- vent this when performing repairs. 1.6.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser produc

36、ts. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before plac- ing the traverse unit (optical pickup) on it. (2) Ground yourself Use a

37、n anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replace- ment optical pickup are shorted. After replacement, re- turn the sho

38、rted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser di- ode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1M Conductive material (conductive sheet) or iron plate (caption) Anti-static wris

39、t strap (No.MA596)6/28 1.7Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific de

40、tails, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connec- tor. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not poss

41、ible to adjust the semi-fixed resistor that ad- justs the laser power. Do not turn it. 1.8Attention when traverse unit is decomposed *Please refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connector on

42、 the servo board. (If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the card wire. 1.9Important for laser products SOLDER 1.CLASS 1 LASER PRODUCT 2.CAU

43、TION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation when open and inter lock

44、failed or defeated. Avoid direct exposure to beam. 4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to d

45、efeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. ! Please use enough caution not to see the beam d

46、irectly or touch it in case of an adjustment or operation check. (No.MA596)7/28 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS 2.1How to repair a fuse pattern 2.1.1Purpose of fuse pattern In order to prevent serious damage on the circuit, fuse pattern is prepared on the GND line of RCA Terminal. This damag

47、e may take due to improper part replacement with a external equipment via RCA line. 2.1.2Repair Procedure (1) Check the shorted circuit at the meltdown point. Need to clean up if the shorted circuit or carbonization happen at the fuse pattern. (2) Add following part on the fuse pattern. (3) Check ou

48、tput level. 2.1.3After finished repair Due to improper part replacement, this meltdown occurs. Thus please notice following information when the unit is returned to your customer. Things to be checked before installing the unit. (1) Check the GND line of external amplifier or other equipment which m

49、ust connect properly. (2) Check whether the GND line is not short-circuited with the battery terminal. (do not short-circuit these lines) 2.2How to identify the CD mechanism ASSY Identification number of the 14 characters are printed on the CD mechanism ASSY upper surface. Part NumberPart NameSPEC F53-0513-08PATTERN FUSE4A Meltdown point Production siteMade at JEINMade at JKEM CD mechanism ASSYFC2-2A00NXNX92-6820-01 PWB ASSYLVA20106-01AX32-6680-00 PW BOARDLVB20106-001BJ76-0898-12 Id