Jvc-KSFX-921-Service-Manual(1) 电路图 维修手册.pdf

《Jvc-KSFX-921-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-KSFX-921-Service-Manual(1) 电路图 维修手册.pdf（41页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LIMITED No.49846 2003/5 CASSETTE RECEIVER 4984620036 KS-FX921 TABLE OF CONTENTS 1Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2、 2Disassembly method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 3Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、. . . . . . . . 1-19 4Description of major ICs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23 SOUND VOLVOL SOURCERF U D ATT Area Suffix U - Other Areas RadioFans.CN 收音机爱 好者资料库 1-2 (No.49846) SPECIFICATION Design and s

4、pecifications are subject to change without notice. AUDIO AMPLIFIER SECTION Maximum Power OutputFront50 W per channel Rear50 W per channel Continuous Power Output (RMS) Front19 W per channel into 4 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear19 W per channel into 4 40 Hz t

5、o 20 000 Hz at no more than 0.8% total harmonic distortion. Load Impedance4 (4 to 8 allowance) Tone Control RangeBass10 dB at 100 Hz Treble9 dB at 10 kHz Frequency Response40 Hz to 20 000 Hz Signal-to-Noise Ratio70 dB Line-Out Level/Impedance2.0 V/20 k load (250 nWb/m) TUNER SECTIONFrequency RangeFM

6、87.5 MHz to 108.0 MHz AM531 kHz to 1 602 kHz FM TunerUsable Sensitivity11.3 dBf (1.0 V/75 ) 50 dB Quieting Sensitivity16.3 dBf (1.8 V/75 ) Alternate Channel Selectivity (400 kHz) 65 dB Frequency Response40 Hz to 15 000 Hz Stereo Separation35 dB Capture Ratio1.5 dB AM TunerSensitivity20 V Selectivity

7、35 dB CASSETTE DECK SECTION Wow & Flutter0.11% (WRMS) Fast-Wind Time100 sec. (C-60) Frequency Response (Dolby B NR OFF)30 Hz to 16 000 Hz (Normal tape) Signal-to-Noise Ratio56 dB (Normal tape) (Dolby B NR ON)65 dB (Dolby B NR OFF)56 dB Stereo Separation40 dB GENERALPower RequirementOperating Voltage

8、DC 14.4 V(11 V to 16 V allowance) Grounding SystemNegative ground Allowable Operating Temperature0C to +40C Dimensions (W H D)Installation Size (approx.)182 mm 52 mm 150 mm Panel Size (approx.)188 mm 58 mm 12 mm Mass (approx.)1.5 kg (excluding accessories) RadioFans.CN 收音机爱 好者资料库 (No.49846)1-3 SECTI

9、ON 1 Precaution 1.1Safety Precautions ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. RadioFans.CN 收音机爱 好者资料库 1-4 (No.49846) SECTION 2 Disassembly method 2.1Main body 2.1.1Removing th

10、e front panel assembly (See Fig.1) (1) Press the release button and remove the front panel as- sembly. Fig.1 2.1.2Removing the bottom cover (See Fig.2) Prior to performing the following procedures, remove the front panel assembly. (1) Turn the main body upside down. (2) Insert a screwdriver under th

11、e joints to release the two joints a on the left side, two joints b on the right side and joint c on the back side of the main body, then remove the bottom cover from the main body. CAUTION: When releasing the joints using a screwdriver, do not damage the main board. Fig.2 2.1.3Removing the front ch

12、assis assembly (See Figs.3 and 4) Prior to performing the following procedures, remove the front panel assembly and bottom cover. (1) Remove the two screws A on the both sides of the main body. (See Fig.3.) (2) Remove the two screws B on the front side of the main body. (See Fig.4.) (3) Release the

13、two joints d and two joints e on the both sides of the main body, then remove the front chassis assembly toward the front. (See Fig.3.) Fig.3 Fig.4 Release button Front panel assembly Bottom cover Joint b Joint b Joint c Joint a Joint a Joint d Joint e Front chassis Joint d A Joint e B Front chassis

14、 assembly (No.49846)1-5 2.1.4Removing the heat sink (See Fig.5) Prior to performing the following procedure, remove the front panel assembly. (1) Remove the two screws C and screw D attaching the heat sink on the left side of the main body, and remove the heat sink. Fig.5 2.1.5Removing the rear pane

15、l (See Fig.6) Prior to performing the following procedure, remove the front panel assembly and bottom cover. (1) Remove the two screws E, three screws F and three screws G attaching the rear panel on the back side of the main body. Fig.6 2.1.6Removing the main board (See Fig.7) Prior to performing t

16、he following procedures, remove the front panel assembly, bottom cover, front chassis assembly, heat sink and rear panel. (1) Remove the two screws H attaching the main board on the top chassis. (2) Disconnect the connector CP701 on the main board from the cassette mechanism assembly. Fig.7 C D Heat

17、 sink G EEF Rear bracket F H Main board CP701 H 1-6 (No.49846) 2.1.7Removing the cassette mechanism assembly (See Fig.8) Prior to performing the following procedures, remove the front panel assembly, bottom cover, front chassis assembly, heat sink, rear panel and main board. (1) Disconnect the wire

18、from the connector CN402 on the mecha board. (2) Disconnect the card wire from the connector CN403 on the mecha board. (3) Remove the four screws J attaching the cassette mecha- nism assembly to the top chassis, take out the cassette mechanism assembly. Fig.8 2.1.8Removing the mecha board (See Fig.9

19、) Prior to performing the following procedures, remove the front panel assembly, bottom cover, front chassis assembly, heat sink, rear panel and main board. (1) Disconnect the wire from the connector CN402 on the mecha board. (2) Disconnect the card wire from the connector CN403 on the mecha board.

20、(3) Remove the screw K attaching the mecha board. (4) Bend the hook f in the direction of the arrow 1 and move the mecha board in the direction of the arrow 2. (5) Remove the mecha board from the mecha bracket (L) of the top chassis. Fig.9 H H HHTop chassis Cassette mechanism assembly J CN402 CN401C

21、N403 Mecha board (No.49846)1-7 2.1.9Removing the front board (See Figs.10 to 12) Prior to performing the following procedures, remove the front panel assembly. (1) Remove the four screws L attaching the rear cover on the back side of the front panel assembly. (See Fig.10.) (2) Release the nine joint

22、s g, the front panel assembly and rear cover become separate. (See Fig.11.) (3) Remove the front board from the front panel assembly. (See Fig.12.) Fig.10 Fig.11 Fig.12 L LL Rear cover Joints g Joints g nt g Joint g ar cover Front panel assem Front board Front panel assembly 1-8 (No.49846) 2.2Casset

23、te mechanism assembly REFERENCE: Prior to performing the following procedures, turn the mode gear on the bottom of the body until the respective part comes to the EJECT position (Refer to Fig.1). Fig.1 2.2.1Removing the cassette guide (See Fig.2) (1) Turn the mode gear to set to RVS play or subseque

24、nt mode. (2) Remove the cassette guide from the main chassis while re- leasing each two joint tabs a in the direction of the arrow. Fig.2 2.2.2Removing the load arm (See Fig.3) (1) Remove the E-washer attaching the load arm. (2) Move the load arm in the direction of the arrow and release the joint b

25、 on the cassette catch. Fig.3 Mode gear Cassette guide Tab a Tab a Load arm E-washer Joint b (No.49846)1-9 2.2.3Removing the cassette hanger assembly / cassette holder (See Fig.4 to 7) (1) Check the mode is set to EJECT. Push down the front part of the cassette holder and move in the direction of th

26、e ar- row to release the joint c. (2) Move the rear part of the cassette hanger assembly in the direction of the arrow to release it from the two joint bosses d. (3) Release the holder stabilizer spring from the hooks e and f, then pull out from the cassette hanger assembly. (4) Bring up the rear si

27、de of the cassette hanger assembly to release the joint g and h. (5) Pull out the cassette catch from the cassette hanger as- sembly. Fig.4 Fig.5 Fig.6 Fig.7 Cassette holder assembly Side bracket Joints c Cassette holder assembly Cassette hanger assembly Boss d Boss d Cassette hanger assembly Casset

28、te stabilizer spring Hook f Hook e Cassette hanger assembly Hook h Hook g Cassette holder assembly Cassette holder assembly Cassette hanger assembly Cassette catch 1-10 (No.49846) 2.2.4Removing the side bracket assembly (See Fig.8 to 10) (1) Remove the screw A attaching the side bracket assembly. (2

29、) Detach the front side of the side bracket assembly upward and pull out forward to release the joint i and j in the rear. CAUTION: When reassembling, make sure that the boss k of the main chassis is set in the notch of the load rack under the side bracket assembly. Do not reattach the load rack on

30、the boss k. CAUTION: After reattaching the side bracket assembly, confirm op- eration. Fig.8 Fig.9 Fig.10 A Side bracket assembly Side bracket assembly Joint i Joint j Joint i Joint j Side bracket assembly Boss k Load rack Boss k Load rack (No.49846)1-11 2.2.5Removing the pinch arm (F) assembly (See

31、 Fig.11 and 12) (1) Remove the polywasher and pull out the pinch arm (F) as- sembly. (2) Remove the compulsion spring. 2.2.6Removing the pinch arm (R) assembly (See Fig.11 and 12) (1) Remove the polywasher and pull out the pinch arm (R) as- sembly. 2.2.7Removing the slide chassis assembly (See Fig.1

32、3 and 14) REFERENCE: It is not necessary to remove the head and the tape guide. (1) Move the slide chassis assembly in the direction of the ar- row to release the two joints l and remove from the main chassis. (2) Remove the rack link. CAUTION: When reassembling, first reattach the rack link, and ne

33、xt fit the boss m and hook n of the slide chassis assembly to the hole of the main chassis, and engage the two joints l. Fig.11 Fig.12 Fig.13 Fig.14 Polywasher Polywasher Pinch arm (F) assembly Pinch arm (R) assembly Polywasher Pinch arm (F) assembly Compulsion spring Pinch arm (R) assembly Polywash

34、er Slide chassis assembly Joint l Joint l Boss m Hook n Rack link Head Tape guide 1-12 (No.49846) 2.2.8 Removing the head / tape guide (See Fig.16 and 17) REFERENCE: It is not necessary to remove the slide chassis assembly. (1) Remove the band attaching the wire to the head. (2) Remove the two screw

35、s B, the head and the head support spring. (3) Remove the pinch arm spring from the tape guide. (4) Remove the tape guide and the pinch spring arm. CAUTION: When reattaching the pinch arm spring, set both end of it to the pinch spring arm (remarked o). CAUTION: When reattaching the head, set the wir

36、es into the groove of the tape guide (Fig.16). 2.2.9Removing the flywheel assembly (F) & (R) (See Fig.18 and 19) REFERENCE: It is not necessary to remove the slide chassis assembly. (1) Remove the belt at the bottom. (2) Remove the two polywashers on the upper side. (3) Pull out each flywheel assemb

37、ly downward. Fig.15 Fig.16 Fig.17 Fig.18 B Slide chassis assembly Head Tape guide B Pinch arm spring Head Head support spring Tape guide Pinch spring arm Slid chassis assembly o o Flywheel assembly (F) Flywheel assembly (R) Belt Polywasher Polywasher Flywheel assembly (F) Flywheel assembly (R) (No.4

38、9846)1-13 2.2.10 Disassembling the flywheel assembly (F) (See Fig.19 and 20) (1) Push and turn counterclockwise the spring holder (F) to re- lease the three joints p on the bottom of the flywheel. (2) The spring holder (F), the TU spring and the friction gear play come off. (3) Remove the polywasher

39、 and felt. 2.2.11 Disassembling the flywheel assembly (R) (See Fig.19 and 20) (1) Push and turn clockwise the spring holder (R) to release the three joints q on the bottom of the flywheel. (2) The spring holder (R), the FF spring and the friction gear FF come off. (3) Remove the polywasher and the f

40、elt. 2.2.12 Removing the reel board (See Fig.21 and 22) (1) Remove the two screws C attaching the reel board. (2) Move the reel board in the direction of the arrow to release the joint r. (3) Unsolder the wires if necessary. CAUTION: When reattaching, confirm operation of the MODE switch and the ST-

41、BY switch.The mode position be- tween EJECT and ST-BY is optimum for reattach- ing.Connect the card wire extending from the reel board to the FFC pad before reattaching the reel board. Fig.19 Fig.20 Fig.21 Fig.22 Flywheel assembly (F) Flywheel assembly (R) Joints p Joint p Joints q Joint q Polywashe

42、r Spring holder (F) TU spring Polywasher Spring holder (R) FF spring Friction gear play Friction gear FF Flywheel assembly (F) Flywheel assembly (R) Felt Felt FFC pad Joint r Reel board C C FFC pad CT-1 switch ST-BY switch Soldering MODE switch 1-14 (No.49846) 2.2.13 Removing the gear base arm / gea

43、r base link assembly (See Fig.23 to 25) (1) Move the gear base arm in the direction of the arrow. (2) Insert a slotted screwdriver to the gear base spring under the gear base arm, and release the gear base arm upward from the boss on the gear base assembly. (3) Remove the gear base arm from the main

44、 chassis while re- leasing the two joints s. (4) Move the gear base link assemby in the direction of the ar- row to release the two joints t. REFERENCE: When reattaching the gear base arm, make sure that the boss on the gear base assembly is inside the gear base spring. 2.2.14 Removing the FFC pad (

45、See Fig.25 and 27) (1) Push each joint hook u of the FFC pad and remove toward the bottom. Fig.23 Fig.24 Fig.25 Gear base link assembly Gear base arm FFC pad Joint t Joint t Joints s Hook u Hook u Gear base arm Screwdriver Gear base spring FFC pad Gear base link assembly Gear base arm (No.49846)1-15

46、 2.2.15 Removing the mode gear (See Fig.26 and 29) (1) Remove the polywasher on the bottom and pull out the mode gear. 2.2.16 Removing the mode switch actuator (See Fig.26, 27 and 29) (1) Pull out the mode switch actuator at the bottom. REFERENCE: When reattaching the mode switch actuator to the mai

47、n chassis, make sure to set on the shaft and insert v into the slot w. 2.2.17 Removing the direction link / direction plate (See Fig.27 to 29) (1) Remove the polywasher attaching the direction link. (2) Bring up the direction link to release the three joints x, y and z at a time. (3) Move the direct

48、ion plate in the direction of the arrow to re- lease the two joints a. REFERENCE: When reattaching the direction plate, engage the two joints a and move in the direction of the arrow (Refer to Fig.28). REFERENCE: When reattaching the direction link, move the direction plate in the direction of the a

49、rrow and engage the three joint x, y and z at a time (Refer to Fig.29). 2.2.18 Removing the mode rack assembly (See Fig.27 and 28) (1) Move the mode rack assembly in the direction of the arrow to release the two joints b and the joint c. REFERENCE: When reattaching, set the two b on the bottom of the mode rack assembly into the slots of the main chassis and move in the direction of the arrow (See Fig.28). Fig.26 Fig.27 Fig.28 Fig.29 Polywasher Mode switch actuator Mode gear Direction plate Direction link Mode rack assembly Slot w Direc