JVC-RXE100SL-avr-sm 电路图 维修手册.pdf

《JVC-RXE100SL-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JVC-RXE100SL-avr-sm 电路图 维修手册.pdf（88页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL AUDIO/VIDEO CONTROL RECEIVER No.20955 May 2001 COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD. RX-E100SL RX-E100SL Area Suffix Contents Safety precautions -1- 2 Importance administering point on the safety -1- 3 Disassembly method -1- 4 Adjustment method -1- 9 Description of major ICs -1

2、-10 16 J C U.S.A Canada DVDTVVCRCDFMAM RX-E100HOME THEATER RECEIVER TV DILECT DVD MEMORY CONTROL ADJUSTSETTING STANDBY D I G I T A L D I G I T A L SURROUND INPUT ANALOG/DIGITAL INPUT ATT MASTER VOLUME SURROUND ON/OFF DSP MODE ANALOGPRO LOGIC SUBWFR LFE SLEEPSTTUNEDMUTING MHZ KHZ VOL AUTO DGTL AUTO I

3、NPUT ATT DSP LCR LSSRS LPCM DOLBY D DTS POWER 1 1 REMOTE CONTROL SURROUND DSP MODE SOUND 1 5 SUBWOOFER +TESTSLEEP 654 EFFECT CENTER + 5 98 REARL + BASS BOOST 5 REARR + MENU 5 CDAM MUTING TV/VIDEO TVVCR FM TV VOL TV/VCR CH DVD + VOLUME POWER 8 7 RM-SRXE100J HOME THEATER RECEIVER 32 INPUT A/D ENTER +1

4、0010 + + 7 TVVCRAUDIODVD RadioFans.CN 收音机爱 好者资料库 RX-E100SL 1-2 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manuf

5、acturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only. 2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations

6、 or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. 3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are oft

7、en not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electric

8、al components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual ma

9、y create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is

10、 required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard testing) After re-assembling the product, always perform an isolation check on the exposed meta

11、l parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outl

12、et. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the

13、AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground. Measure the AC voltage across the

14、resistor with the AC voltmeter. Move the resistor connection to eachexposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. voltage measured Any mu

15、st not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards. 2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained. 3. Repairs must be made in ac

16、cordance with the relevant safety standards. 4. It is essential that safety critical components are replaced by approved parts. 5. If mains voltage selector is provided, check setting for local voltage. Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/vol

17、ts, or more sensitivity) 1500 10W 0.15 F AC TYPE ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. In regard with component parts appearing on the silk-screen printed side (parts side)

18、of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (Except the JC version

19、) http:/getMANUAL.com RadioFans.CN 收音机爱 好者资料库 RX-E100SL 1-3 Caution: For continued protection against risk of fire, replace only with same type 5A/125V for F201, 2A/125V for F202 and F203. This symbol specifies type of fast operating fuse. Precaution: Pour eviter risques de feux, remplacez le fusibl

20、e de surete de F201 comme le meme type que 5A/125V, et 2A/125V pour F202 et F203. Ce sont des fusibles suretes qui functionnes rapide. Importance administering point on the safety LVA10230-A2 CN207 FW201 R201 FC203 FC205 FW202 FC206 FC204 2A-125V 2A-125V LVA10230-A3 CN217 EP202 FC201 PW103PW102PW101

21、 R205 TA201 TA202 FC202 B410 B411 B413 B412 B414 B415 5A-125V RadioFans.CN 收音机爱 好者资料库 RX-E100SL 1-4 Remove the four screws A attaching the top cover on both sides of the body. Remove the three screws B on the back of the body. Remove the top cover from behind in the direction of the arrow while pull

22、ing both sides outward. 1. 2. 3. Disassembly method Removing the top cover (See Fig.1) Prior to performing the following procedure, remove the top cover. Remove the power cord stopper from the rear panel by moving it in the direction of the arrow. Remove the eleven screws E attaching the each boards

23、 to the rear panel on the back of the body. Remove the four screws F attaching the rear panel on the back of the body. 1. 2. 3. Removing the rear panel (See Fig.4) Prior to performing the following procedure, remove the top cover. Disconnect the card wire from connector CN411 on the audio board and

24、CN204 on the power supply board in the front panel assembly. Cut off the tie band fixing the harness. Remove the three screws C attaching the front panel assembly. Remove the four screws D attaching the front panel assembly on the bottom of the body. Detach the front panel assembly toward the front.

25、 1. 2. 3. 4. Removing the front panel assembly (See Fig.2 and 3) Fig.1 Fig.2 Fig.3 Fig.4 A 2 A 2 B Top cover C Power supply board Audio board CN411 Main board Tie band D E E F E F F Cord stopper C Front panel assembly Front panel assembly D Rear panel CN204 F E RX-E100SL 1-5 Prior to performing the

26、following procedure, remove the top cover and the rear panel. Cut off the tie band fixing the harness. Disconnect the tuner board and DSP board from connector CN111 and CN681 on the each Relay board. Disconnect the Relay board from connector CN503 and CN501 on the audio board. Disconnect the card wi

27、re connected to connector CN522 on the Input board. 1. 2. 3. 4. Removing each board connected to the rear side of the audio board (See Fig.5 to 7) Fig.5 Fig.6 Fig.7 DSP board Input board Tuner board DSP board CN111 CN681 CN522 CN503 CN522 Relay board CN501 Relay board Tuner board CN681 CN111 Input b

28、oard RX-E100SL 1-6 Prior to performing the following procedure, remove the top cover , the rear panel and the each board. Removing the audio board (See Fig.8) Remove the ten screws K and four screws L attaching the heat sink. Remove the two screws J attaching the heat sink from the rear side of main

29、 board. 1. 2. Removing the Heat sink (See Fig.10 to 11) Prior to performing the following procedure, remove the top cover, the rear panel and audio board. Remove the harness band fixing the harness. Disconnect the harness from connector CN707 on the power supply board . Disconnect the harness from c

30、onnector CN202 and CN206 on the main board . Remove the five screws H and the two screws I attaching the main board. 1. 2. 3. 4. Removing the main board (See Fig.9) Disconnect the card wire from connector CN411 on the audio board. Disconnect the harness from connector CN205 on the audio board. Disco

31、nnect the harness from connector CN515, CN516, and CN517on the main board. Remove the harness band fixing the harness. Remove the three screws G attaching the audio board assembly. 1. 2. 3. 4. 5. Fig.8 Fig.9 Fig.11 Fig.10 power supply board Power / Fuse board CN411 Audio board Main board rear side M

32、ain board Heat sink CN206 CN205 G CN516 Power transformer CN707 H H H H I I L L KKK J J CN515 CN517 CN202 Harness band Harness band Main board RX-E100SL 1-7 Prior to performing the following procedure, remove the top cover and the rear panel. Disconnect the harness connected to connector CN217 on th

33、e power / fuse board (If necessary, cut off the band fixing the harness on the side of the base chassis). Unsolder the power cord and other harnesses connected to the power / fuse board. Remove the screw O attaching the power / fuse board. 1. 2. 3. Removing the power / fuse board (See Fig.13) Prior

34、to performing the following procedures, remove the top cover. Disconnect the harness from connector CN217 on the power / fuse board (If necessary, cut off the tie band fixing the harness). Disconnect the harness from connector CN201 and CN202 on the power supply board and main board. Remove the four

35、 screws M attaching the power transformer. 1. 2. 3. Removing the power transformer (See Fig.12 and 13) Prior to performing the following procedure, remove the top cover. Disconnect the card wire from connector CN204 on the power supply board. Disconnect the harness connected to connector CN201 and C

36、N707 on the power supply board (If necessary, cut off the band fixing the harness on the side of the base chassis). Disconnect the harness connected to connector CN206 on the main board Remove the three screws N attaching the power supply board. Unsolder the three harnesses connected to the power su

37、pply board. 1. 2. 3. 4. 5. Removing the power supply board (See Fig.12) Fig.12 Fig.13 Power supply board CN707 Power transformer M Solder M Solder N Power / fuse board Power cord Power transformer board PW201 PW203 CN204 PW202 N N CN201 O CN217 Hook CN206 CN202 Tie band Tie band RX-E100SL 1-8 Prior

38、to performing the following procedure, remove the top cover and the front panel assembly. Remove the two screws P attaching the power switch board. Remove the seven screws Q attaching the system control board. 1. 2. Removing the system control board / power switch board (See Fig.14) Fig.14 System co

39、ntrol board Power switch board QPQ RX-E100SL 1-9 Adjustment method 1. Prior to turning the power ON, fully turn the adjusting resistor (VR301(Lch),VR302(Rch) counterclockwise direction and connect the DC voltmeter to the measuring terminal(B451-B452(Lch) , B453-B454(Rch). 2. Set the surround mode OF

40、F. 3. Adjust the resistor so that the measured value becomes 2mV immediately after turning the power ON. 4. When the idling current has been stable (about 30 minutes after the power is turned ON), confirm that the measured value falls within 1.0mV 10mV(2.3mV). Power amplifier section B453-B454 (Rch)

41、 VR301 (Lch) VR302 (Rch) Heat sink Adjustment of idling current Measurement terminalB451-B452(Lch) , B453-B454(Rch) Adjustment volumeVR301(Lch) , VR302(Rch) Attention This adjustment does not obtain a correct adjustment value immediately after the amplifier is used (state that an internal temperatur

42、e has risen). Please adjust immediately after using the amplifier after turning off the power supply of the amplifier and falling an internal temperature. * It is not abnormal though the idling current might not become 0mA even if it is finished to turn variable resistance (VR301VR302) in the direct

43、ion of counterclockwise. B451-B452 (Lch) RX-E100SL 1-10 1 2 3 4 5 6 7 8 9 10 11 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 SDOS I2C SMUTE BICK LRCK SDTI1 SDTI2 SDTI3 SDTO DAUX DFS DZF2/OVF RIN+ RIN- LIN+ LIN- ROUT1 LOUT1 ROUT2 LOUT2 ROUT3 LOUT3

44、 NC DZFE TVDD DVDD DVSS PDN TST NC ADIF CAD1 CAD0 LOOP1 LOOP0/SDA/CDTI DIF1/SCL/CCLK DIF0/CSN P/S MCLK DZF1 AVSS AVDD VREFH VCOM 1.Pin layout AK4527B (IC601) : A/D,D/A Converter Description of major ICs AK4527BVQ Top View No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Pin name SDOS I2C SMUTE BICK

45、LRCK SDTI1 SDTI2 SDTI3 SDTO DAUX DFS NC DZEF TVDD DVDD DVSS PDN TST SDTO Source Select Pin (Note 1) L : Internal ADC output, H : DAUX input Control Mode Select Pin L : 3-wire Serial, H : I2C Bus Soft Mute Pin (Note 1) When this pin goes to H, soft mute cycle is initialized. When returning to L, the

46、output mute releases. Audio Serial Data Clock Pin Input Channel Clock Pin DAC1 Audio Serial Data Input Pin DAC2 Audio Serial Data Input Pin DAC3 Audio Serial Data Input Pin Audio Serial Data Output Pin Sub Audio Serial Data Input Pin Double Speed Sampling Mode Pin (Note 1) L : Normal Speed, H : Doub

47、le Speed No Connect No internal bonding. Zero Input Detect Enable Pin L : mode 7 (disable) at parallel mode, zero detect mode is selectable by DZFM2-0 bits at serial mode. H : mode 0 (DZF is AND of all six channels) Output Buffer Power supply Pin, 2.7V5.5V Digital Power Supply Pin, 4.5V5.5V De-empha

48、sis Pin, 0V Power-Down poser lappareil sur une surface plate. Veiller galement ce que lair circule le mieux possible comme illustr. Front Avant RX-E100SL Spacing 15 cm or more Dgagement de 15 cm ou plus Wall or obstructions Mur, ou obstruction Floor Plancher Stand height 15 cm or more Hauteur du socle: 15 cm ou plus For U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfe