Kenwood-KDCX-589-Service-Manual(2) 电路图 维修手册.pdf
《Kenwood-KDCX-589-Service-Manual(2) 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Kenwood-KDCX-589-Service-Manual(2) 电路图 维修手册.pdf(44页珍藏版)》请在收音机爱好者资料库上搜索。
1、 2005-2 PRINTED IN JAPAN B53-0240-00 (N) 1708 CD RECEIVER KDC-W6531/W6531Y /X589/X7529 SERVICE MANUAL This product uses Lead Free solder. Plastic cabinet assy (A02-2732-03) Lever (D10-4589-04) x2 Screw set KDC-X589: (N09-6212-05) KDC-X7529/W6531 /W6531Y: (N09-6280-05) DC cord (E30-6412-05) Screw set
2、 KDC-X589: (N99-1723-05) KDC-X7529: (N99-1758-05) Mounting hardware assy (J21-9716-03) Remote controller assy (A70-2067-05) MODELTDF PANEL No.TDF NAME KDC-X589Y33-2180-60TDF-55DX KDC-X7529Y33-2180-65TDF-X7529 KDC-W6531/W6531YY33-2180-63TDF-W6531 TDF PANEL INFORMATION Size AA battery (Not suplied) DC
3、 cord (E30-6408-05) Compact disc KDC-X589/X7529: (W01-1643-15) KDC-W6531/W6531Y: (W01-1647-15) Antenna adaptor (T90-0523-05) KDC-X589 KDC-X7529 KDC-W6531 KDC-W6531Y Panel assy (A64-3498-12) Panel assy (A64-3503-12) Panel assy (A64-3511-12) Escutcheon (B07-3125-01) Escutcheon (B07-3125-01) Escutcheon
4、 (B07-3125-01) Depends on the model. Refer to the parts list. CD MECHANISM EXTENSION CORD (24P) : W05-0934-00 A unique identification number (Unique ID) is given to each unit, which is imprinted on the CD mechanism assembly. If and when the mechanism assembly or Flash ROM (IC17) on the mechanism boa
5、rd is replaced, it is necessary to write the Unique ID. For details, refer to “How to Write the Unique ID” on Page 15. RC-527 RadioFans.CN 收音机爱 好者资料库 2 KDC-W6531/W6531Y /X589/X7529 BLOCK DIAGRAM F/E A8V AM+B SW5 RDSSW5 LX-BUS BU AUX E-VOL IC2 CD MECHA SERVO+B A8V BU5V CD5V 3.3VREF. PRE+B A8V A8V 4VP
6、RE-REF. AM+B IC9 IC11 Q300 A8V AM+B SYSTEM u-COM OPELDISP MARINEDISP BU PW-IC PW-IC SVR SP-OUT MUTE PRE-OUT IC10 EEPROM SW5 Q400-405 PRE-OUT(2V/4V) IC902 3.3VREF. SVR/ SVR+B A8VPW-IC SVR 3.3VREF. Q107 EXT-AMP PHONE ACC-DET Q112 DIMMER Q108 SURGE Q109 PAN/ PANEL Q7 BU5V IC12 PCON-SW Q1 Q103 BU-DET Q1
7、11 4V ILL+B Q15 IC5 SVR+B Q9 SW14V Q4 SW5V Q3 ANT-SW Q101 CD SERVO Q9 PAN Q18 A8V Q5 PAN5V Q13 DC-CN BU5PAN5V ILL+B A8V PRE+B SVR+B SERVO+B CD5V BU5 SW5 P-M+B ILL+B M+B PRE+B CD5V DET TYPE-SW OEM TYPE-SW MUTE BU5 BU5 DC-CN etc GUIDE ILL DSI/ BU5 EEP-DET MECHA SLIDE DET MOTOR DRIVER P-M+B RST IC7 IC8
8、 BU5 PAN5 ILL+B CN/FPC MECHA SLIDE CN-DET RESET ENCODER ROTARY REMOSW5V SW SWF+/F- DISP BLACK FL DRIVER ILL KEY-ILLUMI SWILLUMI KEY MATRIX KEY FL IC2-6 IC1 MOTOR+B SW5 Q1 IC1 Q6 PAN5 PAN5 Q2 F+/F- FL+B OUT SW Q4,5 IC4 IC2 FST DXM6580W DXM6800W 3 8 2 8 2 4321043 5 R/R R/L F/R F/L 2 FRONT REAR SUB-WOO
9、FER P ON PON ILL P ON PON PAN CD P ON ANT CONP CON BU EXT-CONT ACC ILLUMI PHONE P-ANT P-CON B.U. MUTEDC-DET PON PAN (PWR OFF ONLY) DET EXT CONT PHONE ACC DET DIMMER 2 3 2 PW-ICE-VOL RST BU DET EXT CONT/PHONE DIMMER/ACC DET P CON/PON BU DET/ANT CON PON PAN CD/PON ILL PON PAN 11 52 SW FUNCTION 55 9 P
10、ON ELECTRIC UNIT (X34-342x-xx/3762-70) (X16- ) RadioFans.CN 收音机爱 好者资料库 KDC-W6531/W6531Y /X589/X7529 3 BLOCK DIAGRAM TR COIL FO COIL C F AB E PD LD SERVO DSP MOTOR DRIVER SP MOTOR LOADING T-99 : Unique ID writing in progress. T-11 : Unique ID Writing complete (success) T-22 : Unique ID Writing comple
11、te (failure) Procedure 5. Changing Unique ID write contents Using Track Up/Down Key, Unique ID contents is changed (In this unit, CONTROL Key is pushed to the left or right.) Using FF/FR Key, Unique ID digit to be worked upon is changed. (In this unit, the CONTROL Key is pushed 1 sec- ond or more to
12、 the left or right) Procedure 6. Final write contents is determined and written to the mechanism. Using Pause key, the ID is written. (In this unit, the center section of the CONTROL Key is to be pressed.) Procedure 7. 63pin of the mechanism microcomputer (TMP91CU27) is set back to Low. (Connection
13、lead is removed.) Procedure 8. Reset the mechanism microcomputer, and start it up. (Resetting the mechanism microcomputer and booting it up again can be achieved by cutting off ACC and Back Up power supply once and then re-starting the unit.) Procedure 9. Insert a Compact Disc (CD) and select CD as
14、the source. This determines the type of media to be played. Then, select from the MENU of the unit “ACD Unique ID.” This is done to confirm on the write content of the Unique ID. When re-doing the procedure, start from Procedure 1 again. 3.2. How to change the Unique ID write content: Explana- tion
15、on the Procedures 5-6. When shifting to the Unique ID Write mode, the display will be as shown in Figure 1. This is the beginning of writing. At this point, as has been indicated above, the digit for 10s in the T- xx is the Unique ID digit which is subject for change and its contents is shown in the
16、 minutes section of the time code. Then, actual change procedure is as follows : The table below shows the keys to be used. Track Up key Push theUnique ID contents+1 of CONTROL Keydigit which is currently to leftsubject to change. Track DownPush theUnique ID contents -1 of keyCONTROL Keydigit which
17、is currently to rightsubject to change. FF keyPush theDigit subject to change +1 CONTROL Key to left for more than 1 second. FR keyPush theDigit subject to change -1 CONTROL Key to right for more than 1 second Pause keyPush theWriting Unique ID CONTROL Key at center Table1. Key to be used in Unique
18、ID Writing mode 3.3. Example of the case of ID to be written is “94850ED2” (Example1). Subject digit of the Unique ID to be changed +1 The subject digit is 3, 3 digit Unique ID is 08 (hexadecimal : 8), the value +1 is 09 (hexadecimal : 9). HOW TO WRITE THE UNIQUE ID KDC-W6531/W6531Y /X589/X7529 17 (
19、Example2). Subject digit of the Unique ID to be changed -1 The subject digit is 7, 7 digit Unique ID is 13 (hexadecimal : D), the value -1 is 12 (hexadecimal : C). (Example3). Digit subject to change +1 The current digit subject to change is 7, digit subject to change +1 is 8. (Example4). Digit subj
20、ect to change -1 The current digit subject to change is 3, digit subject to change -1 is 2. (Example5). Determination of Unique ID (Writing) HOW TO WRITE THE UNIQUE ID T-23 4:08T-34 8:05 FR key T-12 9:04 Pause key T-99 9:04T-11 9:04 Writing complete Display of writing in progress. 4.Note : When in t
21、he Unique ID Write mode, the written Unique ID is not displayed. The terminal of the mechanism microcom- puter must be put back to what it was before (63pin to Low). Then, reset the microcomputer and re-boot it for confirming the newly written Unique ID is correct. How to view the Unique ID q Boot i
22、n normal mode (Not the Write mode) w Insert a CD and set the CD as the source e When reading CD is complete and the media is deter- mined, select “ACD ID” from the unit MENU. After writing the Unique ID on the current mechanism, trans- fer the ID number seal from the old mechanism. In order to start
23、 the special mode (Unique ID Write mode), the 63pin must be changed to High for mode change. When doing this, BU3.3V should be connected as the power sup- ply. In the special mode, when reset, the setting must be changed to High. Unless this is done, the mode does not work. Therefore, the setting mu
24、st be completed as indicated. T-34 9:05T-34 8:05 Track Up key T-78 12:02T-78 13:02 Track Down key T-81 2:09T-78 13:02 FF key 18 KDC-W6531/W6531Y /X589/X7529 ABCDE 1 2 3 4 5 6 7 PC BOARD (COMPONENT SIDE VIEW) R953 C7 R7 C958 W127 TH1 R273 C410 R928 R936 R R316 R317 R318 R319R332 R274 R275 C C435 C436
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Kenwood-KDCX-589-Service-Manual2 电路图 维修手册 Kenwood KDCX 589 Service Manual 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


