Pioneer-SP101-sp-sch电路图 维修手册.pdf

《Pioneer-SP101-sp-sch电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-SP101-sp-sch电路图 维修手册.pdf（6页珍藏版）》请在收音机爱好者资料库上搜索。

1、5. CIRCUIT DESCRIPTIONS The SP-101 is a synthesized surround processor that produces four effects based on the surround data included in surround encoded Laser discs and ordinary stereo broadcasts to give the listener the impression of being in different listening environments. It also has a super b

2、ass synthesizer section to allow the listener to really feel the music. 5. 1 SUPER BASS SYNTHESIZER CIRCUIT This circuit increases the feeling of volume by synthesizing lower harmonics of low range signals to add extra power and depth to low frequency sounds. These lower harmonics are produced by di

3、viding the frequency of the input signal in half. The input signal is first routed through a 150Hz lowpass filter and then four band-pass filters with poles at 63Hz, 80Hz, lOOHz and 125Hz re- spectively. The output of each band-pass filter is split into two routes, one to a level detector circuit an

4、d the other to a limiter circuit. The level detector circuit is an absolute value detector circuit using an operation amp that converts the signal level into a DC voltage. The limiter circuit changes the signal into a square wave by causing the operation amp to operate at saturation. The frequency o

5、f the limiter circuit output signal is divided in half by the T flip-flop and sent to VGA (an amp in which gain can be changed with a control voltage). The gain of each VGA is con- trolled by the output voltage of the corresponding level detector circuit so that the signal level (of the square wave

6、obtained after dividing the input signal frequency in half) is always proportional to the level of the original input signal. All four VGA output signals are mixed and .the upper harmonics of the square wave are removed by a low-pass filter so that the signal contains only lower harmonics. After the

7、 level of this signal is adjusted by the SYNTHE. LEVEL control (a double volume), it is routed through a low-pass filter amp before being mixed with the FRONT L/R and SURROUND L/R signals. Input to the 63Hz and 80Hz circuits can be shut out with the front panel 30Hz and 40Hz CUT switches (the front

8、panel frequency indication rounds off the halved frequencies to the nearest ten). These two switches are provided to allow the user to reduce the super bass effect when desired to avoid the unpleasant effect that can result when too much bass is added to some kinds of music. The output of each level

9、 detector circuit causes each front panel frequency indicator LED to light. Fig. 5-1 The Super Bass Synthesizer Circuit RadioFans.CN 收音机爱 好者资料库 5.2 8URRGUMD PROCESSOR CIRCUIT (Fig. 5-3) This circuit synthesizes signals for two more channels by processing the original L and R channel signals to produ

10、ce the desired feeling of ambience. The signals of the two additional channels are created by making different combinations of the positive and reverse phases of the L and R channel input signals and the two delay ICs, each having a different delay time. This allows the circuit to produce four diffe

11、rent effects. The delay circuit is composed of a 4096-stage BBD IC (MN3005) and a 2048-stage BBD IC (MN3Q08). Both ICs are driven by a 33 kHz 2- phase clock singal. To minimize the degradation of the S/N ratio caused by the use of BBDs, compander ICs (NE571) are used to compress the dynamic range of

12、 the signal on the input side of the delay circuits. The dynamic range is then re- turned to its original width on the output side by an expander, thereby reducing noise. Simulated Stereo Mode The SURROUND L output signal is the L channle signal that has passed through the 4096- stage BBD delay circ

13、uit. The SURROUND R out- put signal is obtained by reversing the phase of the original R channel signal and then passing that signal through the 2048-stage BBD delay circuit. When listening to bilingual and monaural sources, this mode gives sound a feeling that re- sembles stereo reproduction. Studi

14、o Mode The SURROUND L and R output signals are used to produce L and R channel differential signals (L-R, mono). Theater Mode The SURROUND L output signal is the L and R channel differential signal (L-R) that has passed through the 4096-stage BBD delay circuit. The SURROUND R output signal is the di

15、fferential signal (L-R) that has passed through the 2048- stage BBD delay circuit. Stadium Mode The SURROUND L output signal is the L and R channel differential signal (L-R) that has passed through the 4096-stage BBD delay circuit. The SURROUND R output signal is the differential signal (L-R) without any delay added. Both of these signals are output at a higher level than in the other three modes. Fig. 5-2 Signal Processing in the Four Surround Decoder Modes RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 6. BLOCK DIAGRAM