Pioneer-VSXAX4AViS-avr-sm 电路图 维修手册.pdf

《Pioneer-VSXAX4AViS-avr-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-VSXAX4AViS-avr-sm 电路图 维修手册.pdf（274页珍藏版）》请在收音机爱好者资料库上搜索。

1、 ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01

2、, Singapore 159936 PIONEER CORPORATION 2005 ?STANDBY/ON AUDIO/VIDEO MULTI-CHANNEL RECEIVERVSX-AX4AVi INPUT SELECTOR MASTER VOLUME PHASE CONTROL MCACC POSITION AUTO SURR/ STREAM DIRECT PHASE CONTROL DIGITAL PRECISION PROCESSING HOME THX STANDARD SURROUND ADVANCED SURROUND VSX-AX4AVi-S RRV3261 AUDIO/V

3、IDEO MULTI-CHANNEL RECEIVER VSX-AX4AVi-S VSX-AX2AV-S THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). *:Alter the wiring of the power-supply block at the primary winding of Power transformer referring to the Line Voltage Selection described in this Service Manual (“4.19 TRANS1 and PR

4、IMARY ASSYS”). ModelTypePower Requirement The voltage can be converted by the following method. VSX-AX4AVi-SHYXJAC220-230VAC240V, * VSX-AX2AV-SHYXJAC220-230VAC240V, * For details, refer to Important Check Points for Good Servicing. T-ZZK OCT. 2005 printed in Japan RadioFans.CN 收音机爱 好者资料库 VSX-AX4AVi-

5、S 2 1234 1234 C D F A B E SAFETY INFORMATION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products suc

6、h as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a

7、qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health 1.5mm CABLE HOLDER) (*;1.00mm FFC CONNECTOR) (*;1.00mm FFC) 2.0mm FLA

8、T CABLE (*;1.5mm FLAT CABLE) (*;1.00mm FFC CONNECTOR) 1.25mm FFC CONNECTOR(L) PF*PG-* CABLE WIRE BOARD IN 1.25mm FFC 4/100 J5 D20PDY0410E 3203 D15A08-150-2651 * HEAD PHONE ASSY (AWX8639) CN3551 4 FU1 - FU2, 3 *1.5mm J10 8/150 INPUT SELECT ASSY (AWX8640) * *5 3561 AC CORD MAIN*3 TRANS *6 FU4FU5,6FU7,

9、 8 *5 REK1029 HY (T5AL/250V) REK1028 (T4AL/250V) REK1021 (T800mAL/250V) REK1026 (T2.5AL/250V) HY6327:ADG7062ATS7403- AC CORD *6 3066 G D Y U X V W Z AD AA AE NOTES: When ordering service parts, be sure to refer to “EXPLODED VIEWS and PARTS LIST” or “PCB PARTS LIST”. The mark found on some component

10、parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. : The power supply is shown with the marked box. VSX-AX4AVi-S 30 1234 1234 C D F A B E 3.3 AUDIO use an i.LINK cable of less than 11 feet (3.5 m). Check that the

11、 source components conforms to the i.LINK Audio format. Make sure that all components connected between the receiver and the source are switched on. PQLS OFF or PQLS ON is displayed temporarily on your player and the sound output is discontinued. The program format indicators dont disappear when SAC

12、D playback stops. The program format indicators remain lit until another format source is input. This is not a malfunction. Make sure your i.LINK source components are switched on. Check that i.LINK is assigned correctly. You may need to reset the i.LINK database memory in the receiver (use the fron

13、t panel): With the receiver in standby, press ? STANDBY/ON while holding down RETURN. When you see DB CLEAR? appear in the display, press ENTER, then SETUP again to confirm. When youve reset the i.LINK database memory, DB CLEAR SET shows in the display. If DB ERROR is displayed, step through the pro

14、cedure again. You cant get i.LINK to display when using the SIGNAL SELECT button. After upgrading a component, it is not recognized and cannot be selected using the i.LINK connection. Before Making a Diagnosis The i.LINK indicator does not light up even when an i.LINK- equipped component is selected

15、. i.LINK messages You may see the following messages displayed in the front panel display when using the i.LINK interface. MessageExplanation BUS FULL The i.LINK bus has reached its capacity and cannot transmit any more data. CANNOT LINK 1The connection between the receiver and the selected i.LINK-e

16、quipped component is unstable. If the i.LINK cables appear to be connected properly and both the receiver and i.LINK-equipped component are on, switch both units off, then on again to re-establish the connection between them. CANNOT LINK 2The receiver cant identify the selected i.LINK-equipped compo

17、nent. For example, the receiver may not be able to identify an i.LINK-equipped personal computer. LINK CHECKThe receiver is checking the i.LINK network. It does this when components are added to, or removed from the network. The sound may be interrupted if this happens during playback. LOOP CONNECTT

18、he i.LINK network cannot function because the connected components form a loop. NO NAMEWhen an i.LINK-equipped component has no name, this message is displayed instead of the proper component name. NO SIGNALA component is outputting an i.LINK signal that the receiver cannot reproduce. This receiver

19、can only reproduce signals from i.LINK-Audio-equipped components. PQLS OFFThis is displayed on a playback component when PQLS turns off during playback. The sound may be interrupted momentarily when this happens. PQLS ONThis is displayed on a playback component when PQLS turns on during playback. Th

20、e sound may be interrupted momentarily when this happens. UNKNOWNWhen an i.LINK-equipped component name cannot be recognized, this message is displayed instead of the proper component name. VSX-AX4AVi-S 219 5678 56 7 8 C D F A B E Preparations for diagnosis Detach the 1394 Assy with the flexible cab

21、les (FFCs) connected, as shown in the photos below, then make a diagnosis. Procedures 1Remove the bonnet, referring to 7.1.9 DISASSEMBLY. 2Remove the HDMI shield, first removing the three screws. 3Remove the two screws that secure the 1394 connector to the rear panel. 4Remove the rivet that secures

22、the 1394 Assy. 5Remove the 1394 Assy. 6Connect a cable between the 1394 connector and the chassis. 7Connect the source equipment (DVD player), using an iLink cable. 2 5 6 7 2 4 2 HDMI Shield 1394 Assy 1394 Assy 3 2 DVD player iLink cable AF VSX-AX4AVi-S 220 1234 1234 C D F A B E It is assumed that t

23、here is no loose connection or damage in the LCRs. There must not be an abnormality in pattern. The parts marked like are located in the 1394 Assy check points on page 222. Step 2: Power supply Step 1: Connections CN401, CN402 Are the FFCs correctly connected? Connect the FFCs correctly. No , C419 (

24、+ side) C2 (+ side) Is the voltage 5V? NoNo 5V input 3.3V YesYes Do the FFCs work correctly? Is the voltage 3.3V? No Yes Yes CN401, CN402 Is soldering of the connectors OK? No Yes To Step 2 To Step 4 To Step 3 Replace any defective FFC. C Step 3: Operation of the Master Clock Do signals (approx. 0.5

25、 Vp-p) run in all the lines? F G AB ,AB D C428 (+ side)2.5V Is the voltage 2.5V? No E Yes X101Microcomputer clock Is oscillation of 6.14MHz output? No Yes X201Mercury clock Is oscillation of 24.576MHz output? No Yes To Step 5 Step 4: Operation of the Master External I/F H I JA201Connection 1 No Yes

26、Do signals (approx. 0.5 Vp-p) run in all the lines? No Yes JA202Connection 2 1394 Assy Troubleshooting Solder the connectors correctly. Check the INTERFACE Assy . Check the soldering of IC1. If soldering has not been done correctly, replace IC1. Check the soldering of JA202. If soldering has not bee

27、n done correctly, replace JA202. Check the soldering of JA201. If soldering has not been done correctly, replace JA201. Check the soldering of X201. If soldering has not been done correctly, replace X201. Check the soldering of IC401. If soldering has not been done correctly, replace IC401. Check th

28、e soldering of X101 or IC101. If soldering has not been done correctly, replace X101 or IC101. A VSX-AX4AVi-S 221 5678 56 7 8 C D F A B E Check the DIGITAL MOTHER Assy. Step 5: J J IC301 (pin 82) Step 5-1 60958 DVD playback (In a case of no DVD audio output) Is there a data ? No Yes Replace the 1394

29、 Assy. Replace the 1394 Assy. IC301 (pin 2) Is there a data ? No Yes K IC404 (pin 4) Is there a data ? No Yes Check the DIGITAL MOTHER Assy. J J IC301 (pins 98-103) Step 5-2 CLK, DATA DVD-AUDIO playback (In a case of no DVD-AUDIO audio output) Are there clock and data? No Yes Replace the 1394 Assy.

30、IC301 (pins 3-9) Are there clock and data ? No Yes L IC409 (pin 4) Is there a MCK ? No Yes To Steps 5-3-1, 5-3-2 M J X302 (pin 3) Step 5-3 CLK, DATA SACD playback (In a case of no SACD audio output) Is oscillation of 22.5792MHz output? No Yes IC301 (pins 70-72, 75-81) Are there clock and data ? No Y

31、es J IC301 (pins 20, 22-25, 28, 29) Are there clock and data ? No Yes Check the DIGITAL MOTHER Assy. Check the DIGITAL MOTHER Assy. N J IC401 (pins 19-23) Step 5-3-1Normal Are there clock and data ? No Yes O IC405 (pins 12-18) Step 5-3-2SACD DIRECT (Select PURE DIRECT, using the AUTO SURR/STREAM DIR

32、ECT key.) Are there clock and data ? No Yes IC301 (pins 3-9) Are there clock and data ? No Yes Check the soldering of X302. If soldering has not been done correctly, replace X302. Check the soldering of IC301. If soldering has not been done correctly, replace IC301. Check the soldering of IC404. If

33、soldering has not been done correctly, replace IC404. Check the soldering of IC409. If soldering has not been done correctly, replace IC409. Check the soldering of IC301 and IC302. If soldering has not been done correctly, replace IC301 and IC302. Check the soldering of IC301 and IC302. If soldering

34、 has not been done correctly, replace IC301 and IC302. Check the soldering of IC401. If soldering has not been done correctly, replace IC401. Check the soldering of IC301. If soldering has not been done correctly, replace IC301. Check the soldering of IC405. If soldering has not been done correctly,

35、 replace IC405. VSX-AX4AVi-S 222 1234 1234 C D F A B E 1394 Assy Check Points MC GO DBA ENF KLJ I H SIDE A SIDE B 1394 ASSY AF 1394 ASSY AF VSX-AX4AVi-S 223 5678 56 7 8 C D F A B E 7.1.6 iPod INFORMATION iPod players supported by this unit This unit supports iPod, iPod mini, and iPod Photo players o

36、f the third or subsequent generation that have adopted the iPod Dock connector. The iPod cable is available as parts (Part No.: ADE7119). MONITOR OUT screen FL display Cause There is a problem with the signal path from the iPod to the receiver. Measures Switch off the receiver and reconnect the iPod

37、 to the receiver. If this doesnt seem to work, try resetting your iPod. Error Messages i P o d T o p E r r o r I 1 MONITOR OUT screen i P o d T o p E r r o r I 2 MONITOR OUT screen i P o d T o p N o T r a c k ErrorI1 FL display Cause The software version being used with the iPod needs to be updated.

38、 Measures Update the software being used with the iPod (software versions prior to iPod update 2004-10-20 are not supported). Cause There are no playable songs currently stored in the iPod. Measures Input some music files compatible with iPod playback. ErrorI2 FL display NoaTrck VSX-AX4AVi-S 224 123

39、4 1234 C D F A B E Operation check of iPod functions Check the power line (Pin 4, 5) of the iPod connector (CN2804). Note: The equalizer (EQ) function of an iPod player cannot be switched from this unit. * The DIGITAL PRECISION PROCESSING indicator on the front panel light off when switching AUTO SU

40、RR/STREAM DIRECT button to PURE DIRECT or listening through the multichannel analogue inputs. Connect an iPod player to this unit, using an iPod cable. Has charging started? (If charging starts, it means the power line is OK.) No Yes Check Pins 42, 43 of the main microcomputer (IC101). Operation is

41、OK. No Yes No Is a signal output from the SP connector when a digital signal (through a coaxial or optical cable) is input? Diagnose the path between the analog audio line AUDIO L (Pin10,12), AUDIO R (Pin11,13) of the iPod connector and the DSP block. Diagnose the analog audio line (input AMP block

42、SP output connector). NoYes No Diagnose the path between the audio line AVDIOL (Pin10, 12), AVDIOR (Pin11, 13) of the iPod connector and the input function IC (IC6201). Yes Yes Is Pioneer displayed on the iPod player? (If it is displayed, microcomputer control is OK.) When audio data are played back

43、, is a signal output from the Speaker? (If a signal is output, the audio line is OK.) (The audio lines are analog input signals. ) Is a signal output from the SP connector when a signal is input to the MULTI CH IN connector?* VSX-AX4AVi-S 225 5678 56 7 8 C D F A B E 7.1.7 HOW TO UPDATE THE DSP FLASH

44、 ROM BY PLAYING BACK A CD 1. Reset the receiver. Note: Note that all the data the receiver retains will be cleared. Resetting the system Use this procedure to reset all the receivers settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While

45、 holding down the front panel AV PARAMETER button, press and hold STANDBY/ON for about three seconds. The display shows RESET?. 3 Press the front panel ENTER button. The display shows RESET OK?. 4 Press SETUP to confirm. OK appears in the display to indicate that the receiver has been reset to the f

46、actory default settings. Note that all settings will be saved, even if the receiver is unplugged. Procedures Connections Connect this unit and a player, as shown in the figure below. Preparations Burn the provided DSP program to a CD-R, using commercially available software for writing. It is necess

47、ary to select the writing format, For music player, not for PC data format . Note: Depending on the writing format of the commercially available software to be used, data on a CD-R may not be used for DSP program rewriting. If the HDMI indicator does not flash when the disc is played back in the way

48、 indicated in Step 5 below, data burned on the CD-R are not appropriate. To know whether the writing software is OK or not, play back the WMA9Pro stream stored on the last track of the disc. (Refer to Troubleshooting on next section.) If audio data are normally played back, the disc and the player c

49、an be used for updating. If audio data are not correctly played back (with noise, etc.), that writing software is not appropriate. Burn the DSP program on a CD-R disc, using other writing software. Please use DVD plaer based on MTK system (DV-270, 370, 373, 575K, 280, 380, 383, etc. ) ,Mitsubishi system (DV-59AVi, 868AVi, S969AVi, 668AVi, etc. ) or Fujitsu system (DV-343, 444, 545, etc.) DO NOT use DVD player based on ST system (DV- 353, 454, 250, 400, 555K, 2